Channel Plus DMT-24 is a telephone distribution module designed for residential and commercial use. It features 24 telephone outputs, each with individual surge protection. The module also has a built-in disconnect jumper to isolate the telephone service from the system. Ideal for structured wire grid systems, it supports various telephone configurations, including single-line, dual-line, and three-line telephones.
Channel Plus DMT-24 is a telephone distribution module designed for residential and commercial use. It features 24 telephone outputs, each with individual surge protection. The module also has a built-in disconnect jumper to isolate the telephone service from the system. Ideal for structured wire grid systems, it supports various telephone configurations, including single-line, dual-line, and three-line telephones.
Residential Gateway model 8157
by
TM
Telephone Distribution Module
Model DMT-24
Designed for
ChannelPlus and OpenHouse
structured wire grid systems.
Telephone Distribution Module DMT-24
Surge Warning
In ----- Disconnect ------ Out RJ31X
Telephone Outputs
Expansion
®
®
Line Ringing
Warranty
600-236 REV B
Copyright © 2005 Linear LLC
B) Never install telephone jacks in a wet location.
A) Never install telephone wiring during a lightning storm.
D) Use caution when installing or modifying telephone lines.
C) Never touch uninsulated telephone wires or terminals
unless the telephone line has been disconnected at the
network interface.
SAFETY INFORMATION:
IMPORTANT INSTRUCTIONS:
When you use your telephone equipment, basic precautions should always
be followed to reduce the risk of fire, electric shock and injury to persons,
including the following:
1. Read and understand instructions.
2. Do not use this product near water, for example, near a bathtub, wash
bowl, kitchen sink, or laundry tub, in a wet basement, or near a swim-
ming pool.
3. Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltages.
4. Use on UL listed cabinets like the H218A, H236A, H318 and H336.
SAVE THESE INSTRUCTIONS
Linear LLC warrants this product to be free from defects in material and workmanship for 5 years. The time period will be
measured using the date code labeled on the product. Linear LLC is not responsible for damage to the product resulting from the
buyer's improper handling, stocking or warehousing of the product. Any implied warranty arising from the sale of the product
including implied warranties of merchantability and fitness for purpose are limited. Linear LLC shall not be responsible for any
losses, damages or expenses, whether direct, consequential, or incidental arising from the use or the inability to use the product.
Some states and countries do not allow limitations or how long an implied warranty lasts or the exclusion or limitation or
incidental or consequential damages, so the above exclusions may not apply. The Linear LLC warranty gives specific legal rights
in addition to other rights, which may exist and vary from state to state and country to country.
The warranty is limited to repair or replacement of products returned, freight prepaid, to Linear LLC, there is NO PROVISION
FOR LABOR COST OR OTHER REIMBURSEMENTS OF ANY KIND.
1. Failures due to product abuse, such as negligence, improper use, and electrical surge including damage from lightning,
water damage or other damage due to natural disasters are not covered by the warranty. The most common form of product
abuse is surge damage caused by lightning.
2. The warranty shall also be voided by any tampering with the date code, labels or other markings on the product.
3. Products that are damaged in transit to Linear LLC due to improper packaging or by the carrier (shipping company) will not
be covered under the warranty. If the product was damaged or lost by the carrier, it is the sender's responsibility to create a claim
against the carrier.
4. The user is responsible for all labor costs associated with removing, reinstalling and returning the product to Linear LLC.
Linear LLC, at its option, will repair or replace the defective product. Replacements will be made from B-Stock, if an exact
replacement is not available, Linear LLC, at its option, will select the nearest equivalent product. The user is responsible for
freight charges to Linear LLC. Linear LLC will return warranted repaired or replacements by UPS Ground or an equivalent
service. A customer may pay the additional costs for second-day or next-day service.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical
Services at 1-800-999-5225 for an RPA# and other important details.
PRINTER'S INSTRUCTIONS:
MANUAL,DMT-24 - LINEAR P/N: 600-236 B - INK: PROCESS COLOR - MATERIAL: 20 LB. MEAD BOND - SIZE: FLAT 11.000" X 8.500" FINISHED 5.500" X 8.500" - FOLDING: 1-FOLD VERTICAL - SCALE: 1-1- SIDE 1 OF 2
Expansion Jumper
(included)
Install this jumper for normal
operation. Remove to
disconnect telephone
service from the system.
Each line is individually surge protected to 50
Joules and 4000 Amps. Some surges contain
sufficient energy that although your system
has been protected, the surge circuit will be
unable to provide additional protection. When
this happens, the red light for that line will turn
on and the module needs to be returned for
service.
From telephone
company 4 Lines
4 Lines to 24
telephone wall
plates.
Security system connection
(RJ-31X)
Telephone Distribution Module DMT-24
Active Line Indicators
Typical Installation
Label Card: Separate and slide labels into extrusion, or flip the label over for a
blank surface.
Front
Rear
Example
2
Included: (1) Expansion Jumper 24”. (2) Flat Surface Mounting Ears.
(1) Disconnect Jumper (66) Labels
Bedroom
Guest
House 2
Guest
House 2
Bedroom
4
Bedroom
4
Master
Suite 2
Master
Suite 2
Dining
Room
Dining
Room
Office
3
Office
3
Back
Door
Back
Door
Basement
Basement
Family
Room
Family
Room
Bedroom
5
Bedroom
5
Patio
Patio
Master
Suite 3
Master
Suite 3
Guest
Room
Guest
Room
Bathroom
Bathroom
FAX
FAX
Bedroom
6
Bedroom
6
Play
Room
Play
Room
Master
Suite 4
Master
Suite 4
Guest
Room 1
Guest
Room 1
Bathroom
1
Bathroom
1
FAX
2
FAX
2
Bedroom
7
Bedroom
7
Pool
House
Pool
House
Media
Center
Media
Center
Guest
Room 2
Guest
Room 2
Bathroom
2
Bathroom
2
Bathroom
Fitness
Center
Fitness
Center
Children’s
Room
Children’s
Room
PVR
Media
Center 1
Hall
Bathroom
3
Front
Door
Children’s
Room 1
PVR
1
Media
Center 2
Hall
2
Game
Room
Children’s
Room 2
Satellite
Modem
Kitchen
Bat
Phone
Garage
Children’s
Room 3
Satellite
1
Modem
2
Laundry
Room
Garage
Children’s
Room 3
Satellite
1
Modem
2
Laundry
Room
Bedroom
1
Garage
2
Children’s
Room 4
Satellite
2
Office
Living
Room
Bedroom
2
Guest
House
Den
Satellite
3
Office
1
Master
Suite
Master
Suite
Bedroom
3
Guest
House 1
Den
2
Satellite
4
Office
2
Master
Suite 1
Master
Suite 4
Telephone Distribution Module DMT-24
Surge Warning
In ----- Disconnect ------ Out RJ31X
Telephone Outputs
Line Ringing
3
Black
Green
Yellow
Red
Pairs 1 & 2
Pairs 3 & 4
Option: old style wall plate
Pairs 3 & 4
Pairs 1 & 2
RJ-14
Voice Grade Jacks
Cable Color Pin # Connector Color
Pin 1
White/Orange Pin 2 White/Orange
Blue Pin 3 Blue
White/Blue Pin 4 White/Blue
Orange Pin 5 Orange
Pin 6
N/C
N/C
Cable Color Pin # Connector Color
Pin 1
White/Brown Pin 2 White/Orange
Green Pin 3 Blue
White/Green Pin 4 White/Blue
Brown Pin 5 Orange
Pin 6
N/C
N/C
8 position connectors
TRTRT TRR
12345 768
PR2
PR1
PR3
PR4
RJ-11
Single line
telephones,
RJ-14
Dual line
telephones &
RJ-25
Rare
3 line KSU
RJ-45 (wired to TIA
T568A standard)
Ethernet (both 10BaseT
and 100BaseT)
Structured wiring of
phones and data lines
Follow color code for T568A jacks.
Position first pair to channel closest
to end of jack. (Do not untwist
conductor pairs more than 0.5"
from the termination point.)
Keep sheath
close to jack.
1
Using a 110 punch-down tool,
push wires into channels
Repeat for subsequent pairs.
and
trim.
110 punch-
down tool
110 punch-
down tool
2
When all conductor pairs are
terminated, snap on strain relief
caps.
3
Wiring a Cat-5 jack
Keep sheath close to connector
Untwist .5” max.
110 punch down tool
Note order of colors
Wiring a telephone wall plate
Black
Green
Yellow
Red
Wiring a 110 connector
green
black
white
red
yellow
blue
TIP
TIP
TIP
TIP
RING
RING
RING
RING
Cat5
4 pair UTP
blue/white
blue
orange/white
orange
green/white
green
brown/white
brown
pair 1
pair 2
pair 3
pair 4
pair 1
pair 2
pair 3
Solid Color
Twisted-Pair
Wire
Modular connectors
6 position connectors
T
T
T
R
R
R
T
T
T
R
RR
1
1
1
2
2
2
3
3
3
4
4
4
5
5
5
6
6
6
PR2
PR1
PR3
PR2
PR1
PR1
Wire Color Codes
The 110 is a sophisticated
insulation displacement
connection system. To push the
wires between the contact blades,
use only a 110 punch down tool.
Using a screwdriver may not seat
the wire properly and can damage
the contacts.
PRINTER'S INSTRUCTIONS:
MANUAL,DMT-24 - LINEAR P/N: 600-236 B - INK: PROCESS COLOR - MATERIAL: 20 LB. MEAD BOND - SIZE: FLAT 11.000" X 8.500" FINISHED 5.500" X 8.500" - FOLDING: 1-FOLD VERTICAL - SCALE: 1-1- SIDE 2 OF 2
-
1
-
2
Channel Plus DMT-24 is a telephone distribution module designed for residential and commercial use. It features 24 telephone outputs, each with individual surge protection. The module also has a built-in disconnect jumper to isolate the telephone service from the system. Ideal for structured wire grid systems, it supports various telephone configurations, including single-line, dual-line, and three-line telephones.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Channel Plus 2181 Supplementary Manual
-
-
-
-
-
-
-
Nortek Contol CHANNEL PLUS 5445 User manual
-
-
Other documents
-
Open House H618 ChannelPlus Installation guide
-
Channel Vision C-0478 Datasheet
-
Commercial Electric 5023-WH Operating instructions
-
ChannelPlus 5525 5545 User manual
-
Commercial Electric 5025-LA Operating instructions
-
StarTech.com C6KEY110SWH Owner's manual
-
Commercial Electric 5016-BL-5PK Operating instructions
-
Commercial Electric 5016-BL Operating instructions
-
CE TECH 5016-WH-10 Operating instructions
-
Aegis CZ20250 User manual
