Toro 12" x 3' Soil Chain Kit, Dingo Compact Utility Loader Installation guide

Brand: Toro

Model: 12" x 3' Soil Chain Kit, Dingo Compact Utility Loader

Type: Installation guide

Form No. 3353-226 Rev -

12in x 3ft Soil Chain Kit

For Dingo® Compact Utility Loaders

Model No. 108–5540

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Remove the spoils auger.

Left soil tooth

Right soil tooth

8 inch spacer

10 inch spacer

12 inch spacer

Bolt (3/8 x 2-1/2 inches)

Bolt (3/8 x 3-1/2 inches)

Bolt (3/8 x 4-1/2 inches)

Locknut (3/8 inch)

Install the teeth.

No parts required

–

Install the spoils auger.

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Step

Removing the Spoils Auger

No Parts Required

Procedure

1. Lo w er the loader ar ms , stop the engine , and

remo v e the k ey .

2. R emo v e the bolt and n ut securing the spoils

aug er to the trenc her ( Figure 16 ).

3. Star t the engine and raise the loader ar ms

slightly (2 to 3 inc hes).

4. Stop the engine and remo v e the k ey .

5. R emo v e the aug er and retain the bolt and n ut.

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Step

Installing the Teeth

Parts needed for this step:

Left soil tooth

Right soil tooth

8 inch spacer

10 inch spacer

12 inch spacer

Bolt (3/8 x 2-1/2 inches)

Bolt (3/8 x 3-1/2 inches)

Bolt (3/8 x 4-1/2 inches)

Locknut (3/8 inch)

Procedure

T he c hain on y our trenc her comes from the

factor y with teeth designed to dig a 6 inc h trenc h

in soil. T his kit contains the par ts y ou need to

con v er t the c hain into an 12 inc h cutting width

c hain. T he c hain has 32 links , and eac h link can

ha v e dig ging teeth fastened to it and is refer red

to as a tooth position. F or the 12 inc h soil c hain,

the a teeth are fastened onto ev er y other link, for

a total of 16 teeth. At eac h tooth position, the

teeth are fastened in v arious conﬁgurations with

spacers and tubes to v ar y the width of cut. T he

tooth conﬁgurations are ar rang ed along the c hain

to maximize dig ging efﬁciency .

T he teeth are cupped differently de pending on the

side of the c hain to whic h they are fastened (left

or right). T he teeth are fastened to the c hain links

with bolts , n uts , tubes , and spacers of v ar ying sizes .

1. Lo w er the loader ar ms .

Note: Y ou do not need to tur n the engine

on to lo w er the ar ms .

2. R emo v e all of the teeth and other hardw are

from the top span of the c hain.

Important: W hen r emo ving teeth, k eep

the components of each tooth set to gether

so that y ou can assemble them later . Some

of the teeth y ou r emo v e will be r equir ed

later in this pr ocedur e.

3. Star t the engine , raise the trenc her slightly off

the g round using the loader ar ms , and slo wly

r un the c hain forw ard to mo v e the other 16

links to the top .

4. Lo w er the loader ar ms , stop the engine , and

remo v e the k ey .

5. R emo v e the remaining teeth and other

hardw are from the c hain.

6. On an empty c hain link in the front of the

trenc her , install a right soil tooth on the left

side of the c hain as illustrated in Figure 1 .

Important: Ensur e that the teeth point

f orw ard, a w ay fr om the tr encher body .

Figure 1

1. Chain link

4. Bolt (3/8 x 7/8 inch)

2. Right soil tooth 5. Tube

3. Bolt (3/8 x 2-1/2 inches) 6. Locknut (3/8 inch)

7. T w o c hain links behind the ﬁrst tooth y ou

installed, to w ard the body of the trenc her ,

install a right soil tooth on the right side of the

c hain as illustrated in Figure 2 .

Figure 2

1. Chain link

4. Bolt (3/8 x 7/8 inch)

2. Right soil tooth 5. Tube

3. Bolt (3/8 x 2-1/2 inches) 6. Locknut (3/8 inch)

8. T w o c hain links bac k, install a left soil tooth

on the left side of the c hain as illustrated in

Figure 3 .

Figure 3

1. Chain link

4. Bolt (3/8 x 7/8 inch)

2. Left soil tooth 5. Tube

3. Bolt (3/8 x 2-1/2 inches) 6. Locknut (3/8 inch)

9. T w o c hain links bac k, install right and left soil

teeth on both sides of the c hain as illustrated

in Figure 4 .

Figure 4

1. Chain link

5. Bolt (3/8 x 1-1/4 inches)

2. Left soil tooth 6. Tube

3. Right soil tooth

7. Locknut (3/8 inch)

4. Bolt (3/8 x 4 inches)

8. Spacer

10. T w o c hain links bac k, install right and left soil

teeth on both sides of the c hain as illustrated

in Figure 5 .

Figure 5

1. Chain link

4. Bolt (3/8 x 2-1/2 inches)

2. Left soil tooth 5. 8 inch spacer

3. Right soil tooth

6. Locknut (3/8 inch)

11. T w o c hain links bac k, install right and left soil

teeth on both sides of the c hain as illustrated

in Figure 6 .

Figure 6

1. Chain link

4. Bolt (3/8 x 3-1/2 inches)

2. Left soil tooth 5. 10 inch spacer

3. Right soil tooth

6. Locknut (3/8 inch)

12. T w o c hain links bac k, install right and left soil

teeth on both sides of the c hain as illustrated

in Figure 7 .

Figure 7

1. Chain link

4. Bolt (3/8 x 4-1/2 inches)

2. Left soil tooth 5. 12 inch spacer

3. Right soil tooth

6. Locknut (3/8 inch)

13. T w o c hain links bac k, install a left soil tooth

on the right side of the c hain as illustrated in

Figure 8 .

Figure 8

1. Chain link

4. Bolt (3/8 x 7/8 inch)

2. Left soil tooth 5. Tube

3. Bolt (3/8 x 2-1/2 inches) 6. Locknut (3/8 inch)

14. T or que all bolts and n uts y ou installed

previously to 27 to 33 ft-lb (37 to 45 N ⋅ m).

15. Star t the engine , raise the trenc her slightly off

the g round using the loader ar ms , and slo wly

r un the c hain forw ard to mo v e the other 16

links to the top .

16. Lo w er the loader ar ms , stop the engine , and

remo v e the k ey .

17. T w o c hain links bac k from the last tooth y ou

installed, install a left soil tooth on the left side

of the c hain as illustrated in Figure 9 .

Figure 9

1. Chain link

4. Bolt (3/8 x 7/8 inch)

2. Left soil tooth 5. Tube

3. Bolt (3/8 x 2-1/2 inches) 6. Locknut (3/8 inch)

18. T w o c hain links bac k, install a right soil tooth

on the right side of the c hain as illustrated in

Figure 10 .

Figure 10

1. Chain link

4. Bolt (3/8 x 7/8 inch)

2. Right soil tooth 5. Tube

3. Bolt (3/8 x 2-1/2 inches) 6. Locknut (3/8 inch)

19. T w o c hain links bac k, install right and left soil

teeth on both sides of the c hain as illustrated

in Figure 11 .

Figure 11

1. Chain link

5. Bolt (3/8 x 1-1/4 inches)

2. Left soil tooth 6. Tube

3. Right soil tooth

7. Locknut (3/8 inch)

4. Bolt (3/8 x 4 inches)

8. Spacer

20. T w o c hain links bac k, install right and left soil

teeth on both sides of the c hain as illustrated

in Figure 12 .

Figure 12

1. Chain link

4. Bolt (3/8 x 2-1/2 inches)

2. Left soil tooth 5. 8 inch spacer

3. Right soil tooth

6. Locknut (3/8 inch)

21. T w o c hain links bac k, install right and left soil

teeth on both sides of the c hain as illustrated

in Figure 13 .

Figure 13

1. Chain link

4. Bolt (3/8 x 3-1/2 inches)

2. Left soil tooth 5. 10 inch spacer

3. Right soil tooth

6. Locknut (3/8 inch)

22. T w o c hain links bac k, install right and left soil

teeth on both sides of the c hain as illustrated

in Figure 14 .

Figure 14

1. Chain link

4. Bolt (3/8 x 4-1/2 inches)

2. Left soil tooth 5. 12 inch spacer

3. Right soil tooth

6. Locknut (3/8 inch)

23. T w o c hain links bac k, install a right soil tooth

on the left side of the c hain as illustrated in

Figure 15 .

Figure 15

1. Chain link

4. Bolt (3/8 x 7/8 inch)

2. Right soil tooth 5. Tube

3. Bolt (3/8 x 2-1/2 inches) 6. Locknut (3/8 inch)

24. T w o c hain links bac k, install a right soil tooth

on the left side of the c hain as illustrated in

Figure 15 .

25. T or que all bolts and n uts y ou installed

previously to 27 to 33 ft-lb (37 to 45 N ⋅ m).

Step

Installing the Spoils Auger

No Parts Required

Procedure

Important: F ailing to position the spoils

auger cor r ectl y may dama ge the tr encher .

1. Star t the engine and raise the loader ar ms

slightly (2 to 3 inc hes).

2. Stop the engine and remo v e the k ey .

3. Using the bolt and n ut y ou remo v ed previously ,

connect the spoils aug er to the aug er shaft.

P air the hole far thest from the aug er blade , in

the end of the aug er with 1 hole , with the inner

hole on the shaft ( Figure 16 ).

Figure 16

1. Spoils auger

2. Hole position for a 4 inch chain.

3. Hole position for a 6 inch chain.

4. Hole position for a 8 inch chain.

5. Hole position for a 12 inch chain.

4. T or que the bolt and n ut to 75 ft-lb (101 N ⋅ m).

5. Lo w er the loader ar ms .

Toro 12" x 3' Soil Chain Kit, Dingo Compact Utility Loader Installation guide

Toro 12" x 3' Soil Chain Kit, Dingo Compact Utility Loader Installation guide

Toro 12" x 3' Soil Chain Kit, Dingo Compact Utility Loader Installation guide

Related papers

Other documents