WaterWay PD11506 Operating instructions

Brand
WaterWay
Model
PD11506
Type
Operating instructions

This manual is also suitable for

48-FRAME CENTER AND SIDE
DISCHARGE PUMPS
IMPORTANT SAFETY INSTRUCTIONS
When installing this electrical equipment, basic safety
precautions should always be followed, including the
following.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS:
WARNING: Risk of electrical shock. Connect only to a
Ground-Type Receptacle protected by a Ground-Fault Circuit
Interrupter (GFCI). Potential risk of fire, electric shock or
injury to person if misused. Do not install within an outer
enclosure or beneath the skirt of the spa unless so marked.
WARNING: To reduce the risk of injury, do not permit
children to use the product unless they are closely
supervised at all times.
CAUTION: This pump is for use with permanently
installed pools and may also be used with hot tubs and spas
if so marked. Do not use with storable pools. Storable pools
are constructed so that they may be readily disassembled
for storage and reassembled to their original integrity.
SAVE THESE INSTRUCTIONS!
INSTALLATION
Location:
Place pump on level surface. Pump must be installed below
water level. Shut-off valves should be installed on both
the inlet and outlet of the pump for future maintenance.
Installation area should have adequate floor drainage.
Pump should be protected from excessive moisture.
Allow access area large enough to service both pump and
plumbing.
Pump Connections:
The inlet and outlet have Waterway male union threads.
Use Waterway tailpiece assemblies for best connections.
These unions allow the pump to be removed for service
without disturbing the plumbing.
HAND TIGHTEN UNIONS ONLY!
DO NOT use a wrench or any adhesives or solvents!
DO NOT use pipe sealant. Use only Teflon or other sealing
compounds approved for use with plastic. Some pipe
sealants are not approved for use with plastics and will
cause stress cracking of plastic parts. New Installations
often require plumbing inspections. This inspection is
usually conducted using city water pressure. This test should
not exceed 40 PSI during the pressure test. When the filter
and pump are under pressure, insure that all air is removed
from the system. Extreme care must be taken during the
pressure test. Failure to follow test instructions explicitly
can result in personal injury and warranties will be voided.
Motor Wiring:
1. Turn power off before working on any electrical
connections.
2. All wiring must conform to local or national codes.
3. All wiring must conform to the wiring diagram on the
motor nameplate or on the back of the terminal cover.
4. Incoming line voltage must be within 10% of the
nameplate voltage.
5. A solid copper bonding conductor no smaller than No. 8
AWG should be connected from the wire connector on the
motor to all metal parts of the spa or hot tub structure,
and, to all electrical equipment, metal conduit, and metal
piping within five feet of the inside walls of a swimming
pool, spa or hot tub when the motor is installed within
five feet of the inside walls of the spa or hot tub.
6. DO NOT ground to a gas supply line.
7. Ground motor prior to connecting to electrical power.
8. Improper grounding can cause serious injury and damage
to the motor, voiding the warranty.
TROUBLESHOOTING
WARRANTY
For product registration visit: www.waterwayplastics.com.
For Warranty questions or claims please contact point of purchase.
810-0003.0117
©2017 Waterway Plastics
2200 East Sturgis Road, Oxnard CA 93030 • Phone 805.981.0262 • Fax 805.981.9403
www.waterwayplastics.com • waterway@waterwayplastics.com
Designed,
Engineered &
Manufactured
in the USA.
C HEC K VO LTAG E AT TE RMINALS
WITH VO LTM ETE R.
MOTOR
WON'T
S TART:
IF LOW VO LTS :
IF PROPE R VO LTAGE :
IF 0 VO LTS :
FUS E/ B REAKER
TR IPPED GFI
DE FEC T IVE EXT ERNAL S WITC H
C ALL E LEC TR IC IAN
INC OR REC T OR LO OS E
C ONNE C TIONS
THE RMAL PR OTE C TOR T RIPPE D
WINDIN G S WITC H OR
C APAC ITO R FAIL URE
MOTOR
HUMS
WON'T
S TART:
C HEC K VO LTAG E
AT T ER MINAL
WITH VO LTM ETE R.
IF VOLTAG E IS N OT
WITHIN 10% OF
NAME PL ATE , C ALL
EL EC TR ICIAN.
IF PROPE R VO LTAGE :
TIG HT PUMP
RE PLAC E FUS E/ R ES ET BRE AK ER.
RE S ET GFI.
C HEC K S WITC H S ET TINGS
AND CO NNEC TIO NS .
ALLO W MOT OR T O C O OL AND R ES TART.
INS URE WIRING C IRC UIT AGRE ES
WITH D IAGRAM AND L EADS AR E TIG HT.
S EE AN AUT HOR IZED MOT OR
S ER VIC E C ENTE R.
S EIZ ED OR TIG HT M OTO R
TAK E APART PUM P, T URN M OTO R
BY HAND. S EE AN AUT HO RIZ ED
MO TOR S ER VIC E CE NTE R.
WINDIN G S WITC H OR
C APAC ITO R FAIL URE
S EE AN AUT HOR IZED
MO TOR S ER VIC E CE NTE R.
MOTOR
IS
NOIS Y:
C HEC K TO S EE THAT
MO UN TING IS S EC UR E:
BE NT S HAFT:
DIS AS S EMBL E PUMP AND
R UN MO TOR S EPAR ATE
TO DE TER MINE WHET HER
MO TOR NOIS E IS AC C EPTABLE :
LO OS E M OUNTING
TIG HTEN MOUNTING .
BE AR ING NOIS E OR
RO TOR R UB
S EE AN AUT HOR IZED
MO TOR S ER VIC E CE NTE R.
S EE AN AUT HOR IZED MOT OR
S ER VIC E C ENTE R.
MOTOR
RUNS,
THEN
S TOPS:
C HEC K F OR MOT OR
OVER LOAD B Y C HEC KING
AMP D RAW AT MO TOR
TE RMIN AL WIT H AM MET ER,
AMP D RAW S HO ULD B E WITHIN 10 %
OF NAMEPL ATE.
IF MOT OR IS NOT
OVER LOADED :
IF MOT OR IS
OVER LOADED :
TR IPPED BRE AK ER
RE S ET BREAKE R.
INADE QUATE VENT ILATIO N
INC RE AS E VEN TILAT ION.
INC OR REC T LINE VOLTAGE
C HEC K VO LTAG E, IF INC OR REC T
C ALL AN EL EC TRIC IAN.
INC OR REC T WIR ING
INS URE T HAT WIRING CIR C UIT AN D
WIRING DIAGR AM AR E THE S AM E.
INC OR REC T VOLTAGE
INC OR REC T WIR ING
PUMP B INDING
MO TOR BIND ING
C HEC K VO LTAG E, IF INC OR REC T,
C ALL AN EL EC TRIC IAN.
INS URE T HAT WIRING CIR C UIT AN D
WIRING DIAGR AM AR E THE S AM E.
TAK E APART PUM P, LO OK
FO R S IGNS O F R UBBING.
IF MOT OR WILL NOT T UR N BY IT S ELF
S EE AN AUT HOR IZED MO TOR S ERVIC E C ENT ER.
PUM P
RUNS,
NO
FLOW:
C HEC K S HUT O FF
VALVES :
VALVES C LOS E D
OPE N VALVE S.
C HEC K TO S EE THAT PUMP IS
BE LOW WAT ER LEVEL:
C HEC K S HUT O FF VALVE S :
PUMP AB OVE WAT ER LEVEL
RE PLUMB PUMP BELO W WAT ER LEVEL.
AIR LOC K
RE MOVE D RAIN PLUG UN TIL WATER FLO WS
FR OM PUM P. RE PL ACE DR AIN
PLUG AND S TAR T PUMP.
PUM P
RUNS,
NOT
ENOUGH
FLOW:
VISIB LE AIR B UB BLE S
IN RET UR N LIN E:
C HEC K TO S EE
THAT VALVE S ARE
C OM PL ET ELY OPE N:
C HEC K F ILTER
PRE S SURE GAUG E:
LE AK IN S UC TIO N PLUMBING
RE PLUMB PUMP BELO W WATE R L EVE L.
PAR TIALLY C LOS E D VALVE S
OPE N VALVE S.
DIR TY IMPE LLER OR FILT ER
C LE AN FILTE R O R IM PELL ER.
TAK E APART PUM P,
LO OK F OR SIG NS OF RUBBIN G.
SlingerVolute
Housing
Faceplate Volute
Seal Kit
Impeller
Screw
Quarter Slot
Plug & O-Ring
O-Ring
Motor
Slinger
Volute
Housing
Faceplate Volute
Seal Kit
Impeller
Screw
Quarter Slot
Plug & O-Ring
O-Ring
Motor
48-FRAME SIDE DISCHARGE WET END
48-FRAME CENTER DISCHARGE WET END
Motor
Cosmetic Ring
Volute
Seal Kit
Impeller Assembly
Volute Cover
Phillips Screws
O-Ring
Faceplate Volute
O-Ring
TRAP ASSEMBLIES
SIDE DISCHARGE SUPREME - SIDE DISCHARGECENTER DISCHARGE
Lid
Lid
Lid
Basket Basket
Basket
O-Ring O-Ring
O-Ring
O-Ring
1 ½" Union
Gasket
2" Union
Gasket
1 ½"
Split Nut
2"
Split Nut
6" Trap Body
1 ½" x 1 ½"
Supreme Trap Body
1 ½" FTP / 1 ½" Buttress
6" Trap Body
1 ½" FTP / 1 ½" Buttress
x 2" Union Flange
Quarter
Slot Plug
O-Ring
Quarter
Slot Plug
O-Ring
C-Clip
Quarter
Slot Plug
SUPREME SIDE DISCHARGE WET END
  • Page 1 1
  • Page 2 2

WaterWay PD11506 Operating instructions

Brand
WaterWay
Model
PD11506
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents