WaterWay 810-0176 User manual

Brand
WaterWay
Model
810-0176
Type
User manual

WaterWay 810-0176 is a side-mount multi-port valve designed for use with swimming pool filters. It allows you to easily switch between different valve positions to control the flow of water through the filter. The valve has six different positions:

  • Filter: Water flows from the pump through the filter and back to the pool. This is the normal operating position for the filter.
  • Backwash: Water flows from the bottom of the filter through the top and out to waste. This position is used to clean the filter.
  • Rinse: Water flows from the top of the filter through the bottom and out to waste. This position is used to rinse the filter after backwashing.

WaterWay 810-0176 is a side-mount multi-port valve designed for use with swimming pool filters. It allows you to easily switch between different valve positions to control the flow of water through the filter. The valve has six different positions:

  • Filter: Water flows from the pump through the filter and back to the pool. This is the normal operating position for the filter.
  • Backwash: Water flows from the bottom of the filter through the top and out to waste. This position is used to clean the filter.
  • Rinse: Water flows from the top of the filter through the bottom and out to waste. This position is used to rinse the filter after backwashing.
SIDE-MOUNT MULTI-PORT VALVE INSTRUCTIONS
VALVE SETTING: Flow direction through valve.
FILTER: Pump top through filter bottom return - For normal
filtration and vacuuming pool through filter.
BACKWASH: Pump bottom through filter top waste - For reversing flow
for cleaning filter.
RINSE: Pump top through filter bottom waste - For initial start-up
cleaning plus resetting filter bed after back washing.
WASTE: Pump waste for vacuuming directly to waste, lowering
pool level / draining pool.
CLOSED: No circulation past pump port - For shutting off ALL flow
to filter and pool.
RECIRCULATE: Pump return - For by-passing filter, but circulating pool
water. May be plumbed for “off-system” pool water access.
Ideal for jet-air fittings.
Pipe Tab boss provided for optional influent pressure gauge for filter air
relief tube (optional). Tap valve at either RETURN or BOTTOM port areas.
DO NOT obstruct pipe threads. Always use Teflon pipe tape or Permatex
No. 2 for connections to provide a good “living” seal. Add extra sealant if
male pipe fitting is undersized.
To winterize filter and pump per manufacturer’s instructions. To drain water
from valve, depress and rotate valve handle and place handle pointer on
raised portion of index hubs at any “in-between” position. If it becomes
necessary to service or gain access to the valve seat gasket, set handle in
filter position, remove cover screws and lift cover and key assembly out.
To assemble, place valve key so that wedge opening is at TOP PORT
(Handle in Filter Position). Flat edge of cover screw lug should align
with flat edge of body screw lug. Position cover o-ring. Secure assembly
to body with cover screws. Tighten cover screws evenly and alternately.
DO NOT over-tighten.
FUNCTIONS OF VALVE POSITIONS GENERAL INSTRUCTIONS
SIDE-MOUNT MULTI-PORT VALVE PARTS
Item Description
1 Handle
2 Handle Pin
3 Cover
4 Screw
5 Nut
6 Washer
7 Diverter
8 Star Gasket
9 Housing
Item Description
10 Washer
11 Label
12 O-Ring
13 O-Ring
14 Plug
15 O-Ring
16 Spring
17 Sight Glass
18 Gasket
10
11
12
13
14
15
16
17
2
3
4
5
6
7
8
9
1
18
WARRANTY
For product registration visit: www.waterwayplastics.com.
For Warranty questions or claims please contact point of purchase.
810-0176.0618
©2018 Waterway Plastics
2200 East Sturgis Road, Oxnard CA 93030 • Phone 805.981.0262 • Fax 805.981.9403
www.waterwayplastics.com • [email protected]
Designed,
Engineered &
Manufactured
in the USA.
  • Page 1 1

WaterWay 810-0176 User manual

Brand
WaterWay
Model
810-0176
Type
User manual

WaterWay 810-0176 is a side-mount multi-port valve designed for use with swimming pool filters. It allows you to easily switch between different valve positions to control the flow of water through the filter. The valve has six different positions:

  • Filter: Water flows from the pump through the filter and back to the pool. This is the normal operating position for the filter.
  • Backwash: Water flows from the bottom of the filter through the top and out to waste. This position is used to clean the filter.
  • Rinse: Water flows from the top of the filter through the bottom and out to waste. This position is used to rinse the filter after backwashing.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents