Rev. D
INST-606
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Form
DISPLAY MOUNT - CLAMSHELL
PS-004
INSTALLATION INSTRUCTIONS
Product Revision
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Printing Spec:
MOTION ATTACHMENT -
7160-0494 & 7160-0529
repositioned on the opposite side.
the Clamshell, locking it in position.
a .25-20 bolt can be installed thru
a vertical position (not tilted forward),
If the Mount will be permanently used in
1/3
The Display Mount Bracket is attached
to the Clamshell with (4) .38-16 carriage bolts,
flat washers and nuts.
Depending on the equipment being installed the
Display Mount Bracket can be repositioned
approx. 2.0" vertically or approx. .5" side-to-side.
If needed the Clamshell handle can be
Several common mounting hole
patterns are located on the
Display Mount Bracket.
Attach the equipment being used
with appropriately sized hardware.
Clamshell
Bracket
Handle
Display Mount
(4) .38-16 bolts,
washers & nuts
2 x 4
Gamber-Johnson
3-Hole in-line
NEC Triangle
75mm VESA
Gamber-Johnson
AMPS Horizontal
AMPS Vertical
© Copyright 2018 Gamber-Johnson, LLC
Clamshell
Display Mount
3X .25-20 Nylok Nuts
Steel Backup Plate
2X .25-20 Carriage Bolts
1X .25-20 Hex Head Bolt
Nylon Bearing
Nylon Bearing
Steel Backup Plate
Mounting Surface with
Gamber-Johnson Swivel Pattern
2/3
The Clamshell Display Mount can be
mounted on any Gamber-Johnson
pole or console box with a swivel
pattern cutout.
Assemble the components as shown
above.
Tighten the .25-20 nylok nuts to get
the desired amount of friction when
swiveling the Display Mount.
3/3
The Clamshell Display Mount can also
be mounted on various Gamber-Johnson
Motion Attachments, which are then
mounted on a console or pole.
The used of a Motion Attachment allows
adding a keyboard tray with ability to
swivel from side to side and move forward
and back.
Assemble components as shown.
DISPLAY MOUNT
6" LOCKING SLIDE ARM
Display Mount, Clevis, 6" Locking Slide Arm
& Keyboard Tray
APPLY THREADLOCKER
STEEL BACKUP PLATE
NYLON BEARING
NYLON BEARING
CLEVIS
.38-16 NYLOK NUT
KEYBOARD TRAY
DISPLAY MOUNT
9" LOCKING
SLIDE ARM
NYLON BEARING
Display Mount, 9" Locking Slide Arm
& Keyboard Tray
TRAY
STEEL BACKUP PLATE
(2) .25-20 HEX HEAD BOLTS
KEYBOARD
PLATE
STEEL BACKUP
NYLON BEARING
STEEL ANCHOR PLATE
& Keyboard Tray
KEYBOARD TRAY
QUAD-MOTION TS5
Display Mount, Quad-Motion TS5
DISPLAY MOUNT
NYLON BEARINGNYLON BEARING
(3) .25-20 NYLOK NUTS
/
