Gamber-Johnson Upper Pole Specification

Gamber-Johnson
Brand
Gamber-Johnson
Model
Upper Pole
Category
Mounting kits
Type
Specification

Gamber-Johnson Upper Pole is a versatile mounting solution for a wide range of motion attachment devices. It features an adjustable swivel motion, allowing for precise positioning of your equipment. The upper bracket can be easily attached to any DS Lower Tubes or DS Vehicle Bases with an integral lower tube, providing a secure and stable foundation. The two .3/8" dia holes provide additional flexibility for strain relief tie down points or use with a security cable.

Gamber-Johnson Upper Pole is a versatile mounting solution for a wide range of motion attachment devices. It features an adjustable swivel motion, allowing for precise positioning of your equipment. The upper bracket can be easily attached to any DS Lower Tubes or DS Vehicle Bases with an integral lower tube, providing a secure and stable foundation. The two .3/8" dia holes provide additional flexibility for strain relief tie down points or use with a security cable.

Center Upper Pole Assemblies - 5" & 7"
INSTALLATION INSTRUCTIONS
Product Revision Form
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
7160-0177, 7160-0178
REV. A
INST-412
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
The Center Upper Pole Assemblies are
used with any DS Lower Tubes or DS
Vehicle Bases with an integral lower tube.
Remove the (4) .25-20 x .75 Hex Head
Screws holding the upper bracket to the
tube.
Assemble the Motion Attachment device
being used to the upper bracket as shown,
using the hardware and bearing plates
supplied with the Motion Attachment
device.
Adjust the drag on the swivel motion by
tightening the (3) .25 lock nuts as
required.
Reattach the upper bracket to the tube
with (4) .25-20 x .75 Hex Head Screws
and .25 Flat Washers.
Insert Center Upper Pole Assembly the
into Lower Tube or Vehicle Base being
used .
While holding the Center Upper Pole
Assembly at the desired position, tighten
the center bolt securely with a 9/16"
open-end wrench.
Two .3/8" dia holes, are provided as a
strain relief tie down points or for use
with a security cable.
Upper Bracket
Tube
Motion Attachment
(DS-Clevis)
Plastic Bearing
Plastic Bearing
Steel Backup
Plate
  • Page 1 1

Gamber-Johnson Upper Pole Specification

Gamber-Johnson
Brand
Gamber-Johnson
Model
Upper Pole
Category
Mounting kits
Type
Specification

Gamber-Johnson Upper Pole is a versatile mounting solution for a wide range of motion attachment devices. It features an adjustable swivel motion, allowing for precise positioning of your equipment. The upper bracket can be easily attached to any DS Lower Tubes or DS Vehicle Bases with an integral lower tube, providing a secure and stable foundation. The two .3/8" dia holes provide additional flexibility for strain relief tie down points or use with a security cable.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents