Mar 01
User Guide
RS-232C/RS-422 Serial
Interface Option
Mar 01
ii RS-232C/RS-422 Serial Interface Option
Trademarks
The following are trademarks or registered trademarks of their respective owners. Other product names mentioned in
this manual may also be trademarks or registered trademarks of their respective owners. Registered trademarks are
registered in the United States Patent and Trademark Office; some trademarks may also be registered in other
countries. PostScript is a trademark of Adobe Systems Incorporated for a page description language and may be
registered in certain jurisdictions.
Adobe, Adobe PhotoShop, Adobe PageMaker/Adobe Systems Incorporated
OpenVMS, Compaq/Compaq Computer Corporation
Microsoft, MS-DOS, Windows/Microsoft Corporation
The ENERGY STAR logo/United States Environmental Protection Agency. The ENERGY STAR emblem does not
represent EPA endorsement of any product or service.
Proprietary Statement
The digitally encoded software included with your printer is copyrighted. All Rights Reserved. This software may
not be reproduced, modified, displayed, transferred, or copied in any form or in any manner or on any media, in
whole or in part, without the express written permission of the manufacturer.
Copyright Notice
This manual is copyrighted. All Rights Reserved. This manual may not be copied in whole or in part, nor transferred
to any other media or language, without the express written permission of the manufacturer.
The specifications of your printer and the content of this publication are subject to change without prior notice.
Every attempt has been made to verify the accuracy of the content herein
Mar 01
RS-232C/RS-422 Serial Interface Option iii
How This Guide is Organized
Chapter 1 - Installing the Serial Interface in 21 Page-Per-Minute Printers
This chapter explains the procedure for installing the RS-232C/RS-422 Serial Interface option
in 21 page-per-minute laser printers.
Chapter 2 - Installing the Serial Interface in 28 Page-Per-Minute Printers
This chapter explains the procedure for installing the RS-232C/RS-422 Serial Interface option
in 28 page-per-minute laser printers.
Chapter 3 - Installing the Serial Interface in 32 and 40 Page-Per-Minute Printers
This chapter explains the procedure for installing the RS-232C/RS-422 Serial Interface option
in 32 and 40 page-per-minute laser printers.
Chapter 4 - Using the RS232-C/RS422 Ser ial Interface
This chapter lists the Serial Interface setup features and available selections via the control
panel menus. The Serial Interface connector pinouts are listed. Troubleshooting error mes-
sages appearing on the printer’s control panel are also discussed.
Chapter 5 - Troubleshooting
This chapter discusses troubleshooting error messages appearing on the printer’s control
panel. Sources of help, information and technical support are also discussed.
Features of the RS-232C/RS-422 Serial Interface
The RS-232C/RS-422 Serial Interface for your printer provides the following:
• RS-232C or RS-422 support
• Baud rate support from 1200 bps to 115200 bps
• DB-25 female connector
• Quick and easy installation requiring no tools
• Control panel menus enable fast and easy configuration and troubleshooting.
Printer Requirements
Before installing the RS-232C/RS-422 Serial Interface option, you will need to make sure of the follow-
ing two requirements:
• Make sure that your printer has a free network port access slot.
• Make sure that your printer’s “Product Version” is V2.03a or later. If you are unsure of your
printer’s version of code, print a Configuration Summary as described in the user’s guide that came
with your printer. If your printer has an earlier version of code contact your point of purchase.
Mar 01
iv RS-232C/RS-422 Serial Interface Option
Safety Precautions
Safety Precautions
CAUTION: Handling ESD-Sensitive Parts
Many electronic parts use parts that are known to be sensitive to electrostatic discharge (ESD). To
prevent damage to ESD-sensitive parts, follow the instructions below in addition to all the usual
precautions, such as turning off power before removing logic boards:
•
Keep the ESD-sensitive part in its original shipping container (a special “ESD bag”) until you are
ready to install the part into the machine.
•
Make the least-possible movements with your body to prevent an increase of static electricity from
clothing fibers, carpets, and furniture.
•
Use an ESD wrist strap on your wrist if available. Connect the wrist band to the system ground
point. This discharges any static electricity in your body to the machine.
•
Hold the ESD-sensitive part by its edge connector cover; do not touch its pins. If you are removing
a pluggable module, use the correct tool.
•
Do not place the ESD-sensitive part on any metal surface; if you need to put down the ESD-sensi-
tive part for any reason, first put it into its special bag.
•
Metal surfaces are electrical grounds. They increase the risk of damage because they make a dis-
charge path from your body through the ESD-sensitive part. (Large metal objects can be discharged
paths without being grounded.)
•
Prevent ESD-sensitive parts from being accidentally touched by other personnel.
•
Take extra care working with ESD-sensitive parts when cold weather heating is used because low
humidity increases static electricity.
WARNING: To prevent the danger of electric shock, before installing any options be sure to
turn the power switch of the printer to the off [
O
] position and disconnect the power cord from
the wall outlet.
Mar 01
Contents
How This Guide is Organized iii
Features of the RS-232C/RS-422 Serial Interface iii
Printer Requirements iii
Safety Precautions iv
Chapter 1 Installing the Serial Interface in
21 Page-Per-Minute Printers 1-1
About this Chapter 1-2
Installing the RS-232C/RS-422 Serial Interface in 21 Page-Per-Minute
Printers 1-2
Chapter 2 Installing the Serial Interface in
28 Page-Per-Minute Printers 2-1
About this Chapter 2-2
Installing the RS-232C/RS-422 Serial Interface in 28 Page-Per-Minute
Mar 01
vi RS-232C/RS-422 Serial Interface Option
Printers 2-2
Chapter 3 Installing the Serial Interface in
32 and 40 Page-Per-Minute Printers 3-1
About this Chapter 3-2
Installing the RS-232C/RS-422 Serial Interface in 32 and 40
Page-Per-Minute Printers 3-2
Chapter 4 Using the RS-232C/RS-422
Serial Interface 4-1
About this Chapter 4-2
Control Panel MENU structure 4-2
SERIAL SETUP Menu 4-4
Interpreter 4-4
Format 4-4
Serial Mode 4-4
Baud Rate 4-4
Data Bits 4-4
Stop Bits 4-4
Parity 4-5
DTR Ready/Busy 4-5
DTR Onl/Offl 4-5
DTR Error 4-5
RTS Ready/Busy 4-5
RTS Onl/Offl 4-5
RTS Error 4-5
XON Ready/Busy 4-5
XON Onl/Offl 4-6
XON Error 4-6
DTR Polarity 4-6
RTS Polarity 4-6
Robust XON 4-6
Disabling the Serial Interface 4-6
Serial 4-6
Mar 01
RS-232C/RS-422 Serial Interface Option vii
References for OpenVMS users 4-7
RS-232C Serial Cable Pin Assignments 4-7
RS-422 Serial Cable Pin Assignments 4-7
Chapter 5 Troubleshooting 5-1
About this Chapter 5-2
Control Panel Error Messages 5-2
Example 5-2
Obtaining Help and Information 5-2
Your Point of Purchase 5-3
Your Application Vendor 5-3
Technical Support 5-3
Mar 01
viii RS-232C/RS-422 Serial Interface Option
Mar 01
1-2 RS-232C/RS-422 Serial Interface Option
Installing the RS-232C/RS-422 Serial Interface in 21 Page-Per-Minute Printers
About this Chapter
This chapter explains the procedure for installing the RS-232C/RS-422 Serial Interface option in 21
page-per-minute laser printers.
Installing the RS-232C/RS-422 Serial Interface in 21 Page-Per-Minute Printers
1.
Carefully review the safety precautions in the front of this guide before starting this installation
procedure.
2.
Ensure that the printer power switch is set to the OFF [ O ] position and unplug the power cord
from the AC outlet.
3.
Loosen the thumbscrews at the top and bottom of the left side cover by turning them in a
counter-clockwise direction.
Mar 01
RS-232C/RS-422 Serial Interface Option 1-3
4.
Slide the cover towards the rear of the printer and then downwards to remove it.
5.
Turning thumbscrews counter-clockwise, remove the blank metal plate covering one of the avail-
able network ports on the controller bracket.
NOTE: It is not necessary to remove the controller from your printer to install the serial interface. For
clarity, the following illustrations depict a controller removed from the printer. When facing the
front of the controller as shown below, network port 1 is on the right and network port 2 is on the
left. However, when installed in the printer, network port 1 is on the bottom and network port 2 is on
top. In the following few steps, a serial network interface is being installed in network port 2.
Mar 01
1-4 RS-232C/RS-422 Serial Interface Option
Installing the RS-232C/RS-422 Serial Interface in 21 Page-Per-Minute Printers
6.
While aligning the front bracket of the serial interface assembly to the two respective thumbscrews
on the controller assembly bracket, firmly seat the 80-pin male connector on the underside of the
interface to the 80-pin female connector on the controller assembly.
7.
Secure the serial interface assembly to the controller bracket by tightening the two smaller thumb-
screws in a clockwise direction.
Mar 01
RS-232C/RS-422 Serial Interface Option 1-5
8.
Insert the top part of the left side cover into the printer. Ensure the locking tab aligns with the hole
in the printer’s side.
9.
Slide the side cover towards the front of the printer to install it.
10.
Tighten both thiumbscrews in a clockwise direction.
Mar 01
1-6 RS-232C/RS-422 Serial Interface Option
Installing the RS-232C/RS-422 Serial Interface in 21 Page-Per-Minute Printers
11.
Connect the power cord to the wall outlet and turn the printer power switch to the ON [ I ] position.
The installation of your RS-232C/RS-422 serial interface option in your 21 page-per-minute printer is
now complete. Proceed to
Chapter 4
Using the RS-232C/RS-422 Serial Interface.
•••
Mar 01
2-2 RS-232C/RS-422 Serial Interface Option
Installing the RS-232C/RS-422 Serial Interface in 28 Page-Per-Minute Printers
About this Chapter
This chapter explains the procedure for installing the RS-232C/RS-422 Serial Interface option in 28
page-per-minute laser printers.
Installing the RS-232C/RS-422 Serial Interface in 28 Page-Per-Minute Printers
1.
Carefully review the safety precautions in the front of this guide before starting this installation
procedure.
2.
Ensure that the printer power switch is set to the OFF [ O ] position and disconnect the power cord
from the wall outlet.
Mar 01
RS-232C/RS-422 Serial Interface Option 2-3
3.
Locate the recessed area near the top of the rear of the printer and pull on the recesed area to open
the rear cover.
4.
Remove the cover on the left side of the printer by first sliding the cover toward the rear of the
printer, then pulling the bottom of the cover toward you and then down.
Mar 01
2-4 RS-232C/RS-422 Serial Interface Option
Installing the RS-232C/RS-422 Serial Interface in 28 Page-Per-Minute Printers
5.
Remove the cover shield by first loosening the two thumbscrews in a counter-clockwise direction
and then gently pulling towards you.
6.
Turning thumbscrews counter-clockwise, remove the blank metal plate covering one of the avail-
able network ports on the controller bracket.
NOTE: It is not necessary to remove the controller from your printer to install the serial interface. For
clarity, the following illustrations depict a controller removed from the printer. When facing the
front of the controller as shown below, network port 1 is on the right and network port 2 is on the
left. However, when installed in the printer, network port 1 is on the bottom and network port 2 is on
top. In the following few steps, a serial network interface is being installed in network port 2.
Mar 01
RS-232C/RS-422 Serial Interface Option 2-5
7.
While aligning the front bracket of the serial interface assembly to the two respective thumbscrews
on the controller assembly bracket, firmly seat the 80-pin male connector on the underside of the
interface to the 80-pin female connector on the controller assembly.
8.
Secure the serial interface assembly to the controller bracket by tightening the two smaller thumb-
screws in a clockwise direction.
Mar 01
2-6 RS-232C/RS-422 Serial Interface Option
Installing the RS-232C/RS-422 Serial Interface in 28 Page-Per-Minute Printers
9.
Replace the cover shield as shown and tighten the two thumbscrews.
10.
Replace the side cover of the printer.
11.
Connect the 25-pin serial cable to the 25-pin serial connector of the serial interface.
NOTE: See “RS-232C Serial Cable Pin Assignments” on page 4-7 and “RS-422 Serial Cable Pin
Assignments” on page 4-7.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/