Lifetime 90569 Owner's manual

Icon Legend................................2

Notices....................................3

Initial Setup...............................4

Pole Assembly.............................7

Extension Arm Assembly............10

Handle Assembly......................14

Backboard to Rim Assembly........17

Parts Identiﬁ er..........................i-iv

Backboard to Pole Assembly.......24

Final Assembly..........................27

Maintenance Instructions..........32

Registration........................33

Warning Sticker........................34

Warranty................................35

TABLE OF CONTENTSTOOLS REQUIRED

3/4" (x2)

5/16"

(x1, included)

Rubber Mallet

Electric Drill

Carpenter’s Level Shovel

(80 lb bag x 8)

Cement

Tape Measure

1/2" (x2)

3/8"

(x1, included)

9/16" (x2)

CONTACT LIFETIME CUSTOMER SERVICE:

Call: 1-800-225-3865

7:00 am–5:00 pm (Monday–Friday) MST

and 9:00 am–1:00 pm Saturday MST

QUESTIONS?

Model Number: 90569

Product ID:

For Customer Service in Mainland

Europe and the United Kingdom,

E-mail: [email protected]

Live Chat: www.lifetime.com

(click on “Live Chat” tab)

Video Instructions:

www.youtube.com/lifetimeproducts

Pour le français, voir la page 2. Para el español, ver la página 3.

ASSEMBLY INSTRUCTIONS

MODEL 90569

CRANK ADJUST

®

BASKETBALL SYSTEM

• Assembly requires at least eight 80-lb. bags of

concrete mix. Before digging, call to locate any

buried utility lines.

• 3+ people recommended for setup.

BEFORE ASSEMBLY:

Save this instruction in the event

that the manufacturer has to be

contacted for replacement parts.

GET ASSEMBLY HELP

WATCH THE INSTRUCTIONAL VIDEOS ON YOUTUBE

Scan the code, or search http://go.lifetime.com/90569playlist

COPY

2

1189602 B

2/11/2019

• Indicates the parts to be used for a section.

• Indicates special heed should be taken when reading.

• Indicates the hardware to be used for a section.

• Indicates the tools to be used for a section.

• Indicates no hardware required for a speciﬁ c page.

• Indicates no parts required for a speciﬁ c section.

• Indicates to use/not to use an electric drill for a speciﬁ c step.

ICON LEGEND

• Indicates the use of a Centerlock Nut. A Nut with this marking will require some effort to tighten.

This hardware was designed with this feature in order to prevent loosening later.

COPY

3

WARNINGS & NOTICES

Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.

To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing

material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware

identiﬁ er and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the

risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

Owner must ensure that all players know and follow these rules for safe operation of the system.

• If using a ladder during assembly, use extreme caution.

• Three capable adults are recommended for this operation.

• Check base daily for leakage. Leaks will cause system to fall.

• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.

• Minimum operational height is 6 ft 6 in (1.98m) to the bottom of the backboard.

SAFETY INSTRUCTIONS

COPY

4

Metal Parts

AEZ (x4)

AEI (x4)

Carpenter’s Level Shovel

(80 lb bag x 8)

Cement / Cemento / Ciment

Tape Measure

3/4"

(x2)

Hardware Blister Pack

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

INITIAL SETUP

1

AOE (x8)

AE0 (x1)

CYV (x1)

AKT (x1)

FNG

COPY

5

TOOLS AND HARDWARE REQUIRED

X SECTION 1 (CONTINUED)

1

• Dig a hole 30” (76.2 cm) deep and 21” (53 cm) square. The edge of the hole should be ﬂush with the edge of the

playing court. If you live in an area where frost heaves may pose a problem, consult your local building inspector to

determine the appropriate hole depth. Bell out the bottom of the hole as illustrated. We recommend building a form

to keep the top of the concrete level and square. Place the form so it is level with the playing surface.

21”

30”

21”

Before digging, call to locate any buried utility lines.

CAUTION

!

3/4” (x2)

1.1

!

• There must be a 3’ (92 cm) area

behind the pole to allow the user to

adjust the Rim height.

1.2

AEI

AOE

AOE (x8)

• Thread a 1/2” Hex Nut (AOE) all the way onto each J-Bolt (AEI). Slide the threaded ends of the J-Bolts through the corner

holes in the Template (AKT), and secure them completely with 1/2” Hex Nuts (AOE). Insert the Bolt (AEO) through the center

hole in the Template and tighten the Nut Coupler (CYV) onto the Bolt as far as it will go.

AKT

CYV

AOE

AEO

!

• Ensure the curved ends of the

J-Bolts point outward away from the

corners as shown.

6

TOOLS AND HARDWARE REQUIRED

X SECTION 1 (CONTINUED)

• Center the Template (AKT) over the hole. Insert the

J-Bolts (AEI) into the concrete and agitate the Template

assembly to eliminate any air bubbles. Push the

J-Bolts into the cement until the Template is

resting ﬂat against the cement. Form the cement

into a downward slope toward the playing surface

to allow water runoff. The lower four Hex Nuts (AOE)

will be in the concrete permanently. Clean off any

concrete on the Template or the exposed portion

of the J-Bolts. Using a carpenter’s level, ensure the

Template is square to the playing surface. Plate should

be level and about 1/2” above the playing surface

for water to drain off of the steel.

18” (20 cm)

AEZ

(80-lb Bag x 8)

• If you are using concrete mix, mix the concrete

according to the instructions on the bags. Please

note that a thicker mix of concrete will dry stronger.

Pour the concrete into the hole, stopping about

18” (46 cm) from the top of the hole. Push the

four pieces of 24” Rebar (AEZ) ﬁrmly to the bottom

of the hole. The Rebar should be arranged in a

square about 8” (20 cm) wide in the center of

the hole so each piece will be next to a J-Bolt

when it is placed in the cement. Finish ﬁlling

the hole to the top with concrete. The top of the

concrete should extend about 1/2” (13 mm)

above the playing surface and slope downward

toward the playing surface to allow water runoff.

1.3

!

• You are now ﬁnished with the initial assembly steps. DO NOT

PROCEED WITH THE ASSEMBLY until the concrete has fully cured.

Curing will take a minimum of 72 hours (3 days). In humid climates

or wet weather, allow additional time for the concrete to cure. Never

use the system without ﬁrst following the cementing instructions.

1.4

AKT

AEI

AOE

Playing surface

7

Hardware Blister Pack

HARDWARE REQUIRED

POLE ASSEMBLY

2

CMV (x1)

EJG (x2)

CUB (x2)

BCO

PARTS REQUIRED

ALH (x1)

ALE (x1)

EJS (x2)

Large Parts

TOOLS REQUIRED

9/16" (x1)

5/16"

(x1, included)

EJH (x4)

Electric Drill

ELW (x1)

8

TOOLS AND HARDWARE REQUIRED

X SECTION 2 (CONTINUED)

2.1

The gussets and small

hole face the same

direction

WARNING

The Poles must be seated together! Even if the Poles cover

the slots before seating, they must be struck on a hard

surface three times! Failure to seat the Poles correctly

could allow the Poles to separate during use, which could

lead to serious personal injuries or property damage.

2.2

• Raise the pole assembly about 12 inches off

the ground. Strike the end of the poles against

a piece of scrap wood or thick cardboard three

times to ensure the poles are seated properly.

WARNING

Do not hit your feet with the Pole Sections, as

serious injury could occur.

6x

ALH

ALE

3x

• Slide the ﬂared end of the Top Pole (ALH) onto

to the swaged end of the Bottom Pole (ALE). The

small hole in the bottom of the Top Pole should

face away from the playing surface.

small

hole

• If you have trouble with this section, scan the QR code to view a video on how to assemble the Pole.

• http://go.lifetime.com/crankadjustpole

9

TOOLS AND HARDWARE REQUIRED

X SECTION 2 (CONTINUED)

• Attach the Pole Brackets (EJS) to the Top Pole (ALH) with the hardware shown.

CMV (x1)

CMV

2.3

• Use an electric drill to secure the Top Pole to the Bottom Pole using a Self-Tapping Screw (CMV). You may need to

use a hex driver or chuck the Self-Tapping screw directly into an electric drill.

9/16"

5/16"

EJG (x2)

EJG

ALH

EJG

CUB (x2)

EJH (x4)

EJH

CUB

EJS

CUB

EJH

2.4

10

CUG (x2)

AEG (x4)

CYF (x2)

EJM (x2)

EJL (x1)

DIQ (x4)

CZF

Hardware Blister Pack

HARDWARE REQUIRED

EXTENSION ARM ASSEMBLY

3

CUB (x1)

AKE (x1)

Metal Parts

TOOLS REQUIRED

PARTS REQUIRED

AKD (x2)

3/4"

3/8" (included)

9/16"

5/16" (included)

Rubber Mallet

AOQ (x1)

11

TOOLS AND HARDWARE REQUIRED

X SECTION 3 (CONTINUED)

CUG

AEG

CYF

DIQ

AKE

3/4"

3/8"

CUG (x1)

AEG (x2)

CYF (x1)

DIQ (x2)

3.1

• Secure the Lower Extension Arm Assembly (AKE) through the ﬁrst set of holes on the Pole above the Handle Brackets.

Ensure the Large Plastic Washers (DIQ) are placed between the Extension Arms and the Pole on each side.

• I

f

you have trouble with this section, scan the code below to view a video on its assembly.

• http://go.lifetime.com/crankadjustarms

12

TOOLS AND HARDWARE REQUIRED

X SECTION 3 (CONTINUED)

3.2

• Install the Bolt (EJL) through the Pole with a long Rubber Spacer (EJM) on either side. Make sure the back end of the

Extension Arm Assembly remains beneath this hardware.

EJL

EJM

CUB

EJM (x2)

EJL (x1)

CUB (x1)

9/16"

5/16"

13

TOOLS AND HARDWARE REQUIRED

X SECTION 3 (CONTINUED)

3.3

• Attach the Upper Extension Arms (AKD) to the Pole as shown.

CUG (x1)

CUG

AEG

CYF

DIQ

CYF (x1)

AEG (x2)

DIQ (x2)

3/4"

3/8"

AKD

14

EJQ (x1)

Hardware Blister Pack

HARDWARE REQUIRED

HANDLE ASSEMBLY

4

CUG (x1)

CYF (x2)

AEG (x4)

DIQ (x2)

BCT

ELX (x1)

PARTS REQUIRED

Large Parts

TOOLS REQUIRED

3/4"

3/8"

15

TOOLS AND HARDWARE REQUIRED

X SECTION 4 (CONTINUED)

AEG

CYF

CYF (x1)

3/4"

3/8"

CUG (x1)

AEG (x2)

CUG

ELX

• Align the Spacer at the top of the Crank Adjust Assembly (ELX) with the holes in the Lower Extension Arms. Secure

using the hardware shown, but do not overtighten this hardware.

4.1

• I

f

you have trouble with this section, scan the code below to view a video on its assembly.

• http://go.lifetime.com/crankadjusthandle

16

TOOLS AND HARDWARE REQUIRED

X SECTION 4 (CONTINUED)

3/4"

3/8"

4.2

• Install the hardware indicated in the location shown. Make sure the Large Plastic Spacers (DIQ) are placed between

the Crank Adjust Assembly and the Pole Brackets.

CYF (x1)

EJQ (x1)

AEG (x2)

AEG

AEG CYF

DIQ

EJQ

DIQ (x2)

17

BACKBOARD TO RIM ASSEMBLY

5

Hardware Blister Pack

PARTS REQUIRED

HARDWARE REQUIRED

AJI (x1)

Glass and Metal Parts

ANK (x4)

ABK (x4)

ADX (x2) BGZ (x1)

ANL (x1)

5 9/16”

AAX (x1)

ABD (x8)

ANM (x2)

ABB (x2)

ANN (x2)

ANJ (x2)

ELG (x2)

BCS

18

BACKBOARD TO RIM ASSEMBLY

5

TOOLS REQUIRED

Metal Parts

PARTS REQUIRED

AMB (x1)

AMA (x1)

BGY (x1)

AMC (x1)

AMK (x1)

BPZ (x1)

BQA (x1)

1/2” 9/16” 3/4”

(1)

(2) (2) (2)

ALX (x1)

ALY (x1)

ANO (x1)

i

This page intentionally left blank

Remove This Section

PARTS IDENTIFIER

ii

Parts shown at 25% of Actual Size

PARTS IDENTIFIER

Remove This Section

Parts shown at 10% of Actual Size

Metal Parts

AMB (x1)

AMA (x1)

BGY (x1)

AMC (x1)

AMK (x1)

BPZ (x1)

BQA (x1)

ALX (x1)

ALY (x1)

ALH (x1)

ALE (x1)

EJS (x2)

ANO (x1)

Page is loading ...

Lifetime 90569 Owner's manual

Lifetime 90569 Owner's manual

Related papers

Other documents