BMW 65 12 0 029 886 Installation Instructions Manual

BMW
Brand
BMW
Model
65 12 0 029 886
Category
Signal cables
Type
Installation Instructions Manual

This manual is also suitable for

BMW 65 12 0 029 886 is a CD changer installation kit designed specifically for BMW X5 (E53) vehicles with a production date before 10/01. It allows for the integration of a CD changer into your vehicle's audio system, providing you with convenient access to your music collection.

The kit includes all the necessary cables, connectors, and mounting hardware to ensure a seamless installation. Once installed, you can enjoy the convenience of controlling your CD changer through your vehicle's audio system, allowing you to change tracks, browse albums, and adjust volume with ease while keeping your hands on the wheel.

BMW 65 12 0 029 886 is a CD changer installation kit designed specifically for BMW X5 (E53) vehicles with a production date before 10/01. It allows for the integration of a CD changer into your vehicle's audio system, providing you with convenient access to your music collection.

The kit includes all the necessary cables, connectors, and mounting hardware to ensure a seamless installation. Once installed, you can enjoy the convenience of controlling your CD changer through your vehicle's audio system, allowing you to change tracks, browse albums, and adjust volume with ease while keeping your hands on the wheel.

Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 576
BMW Parts and Accessories
Installation Instructions
BMW CD changer installation kit
BMW X5 (E
53)
These installation instructions are only valid for cars with a production date before
10/01
Technical and electrical knowledge required
The installation time is 0.5 - 3.5 hours but this may vary depending on the condition
of the car and the equipment in it.
Retrofit/Installation kit No. 65 12 0 029 883
65 12 0 029 886
65 12 0 140 746
65 12 0 140 747
F 53 0751 B
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 576
Contents
Section Page
1. Important information on installing the CD changer in the E53 . . . . . . . . . . . . . . . . 3
2. Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. To install the audio module holder (only required in cars
without an audio module holder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7. To install the CD changer (cars without an on-board monitor,
without a DSP amplifier and with Professional radio SA663
up to production date 03/01 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. To install the CD changer (cars without an on-board monitor,
without a DSP amplifier and with Professional radio SA663
after production date 04/01 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9. To install the CD changer (cars with an on-board monitor and
without a DSP amplifier only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
10. To install the CD changer (only required for cars with a DSP amplifier) . . . . . . . . . . 23
11. To install the CD changer (only required for cars with CD changer preparation) . . . 25
12. Coding and concluding work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
13. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
14. Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
EN/3
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
1. Important information on installing the CD changer in the E53
Only for use in the BMW dealer organisation.
The CD changer may only be installed by a specialist workshop that has the required special
tools and manuals (servicing, repair, diagnostics, etc.).
All the work is shown for the left-hand side of the car and must be repeated on the
right-hand side.
In cars with an on-board monitor radio the control cable is only installed in the boot.
In cars with a BMW Professional hi-fi system DSP amplifier only the coaxial cable for the
Professional hi-fi system DSP amplifier/CD change must be installed in the boot.
Ensure that the cables/lines are not kinked or damaged as you install them in the car.
Additional cables/leads that you install must be secured with cable ties.
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals
must be used.
Subject to technical modifications
Required tools and equipment
Set of flat screwdrivers Set of Allen keys
Set of Philips screwdrivers 1/2 inch socket set
Angle cutter Set of Torx sockets
1/4 inch socket set BMW disconnection tool
Cable lamp Hot air blower
EN/4
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
2. Preparations
TIS
instruction
No.
Print out error memory -
Disconnect the battery 12 00 ...
Remove the rear left boot trim 51 47 151
Cars without an audio module holder and no power supply wiring harness
Remove the rear left wheel arch trim 51 47 151
Remove the boot floor or loading aid 51 47 101
Only required for cars with an on-board monitor radio
Remove the boot floor or loading aid 51 47 101
Remove the spare wheel -
Remove the cover on the on-board monitor radio -
Only required for cars without an on-board monitor radio.
Remove the radio 64 11 030
Remove the air conditioning control 64 11 749
Loosen the centre console 51 16 200
Remove the rear seat bench 52 24 005
Remove the left footwell light 51 45 180
Remove the rear left door sill strip 51 43 150
Remove the left side section 52 26 008
Remove the combination roller blind (if fitted) -
Remove the boot floor or loading aid 51 47 101
Remove the boot floor on the left (if a loading aid is fitted) 51 47 141
Remove the boot ventilation grille on the left. 51 47 151
Remove the left boot trim 51 47 151
EN/5
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
3. Parts list
2
3
4
6
7
8
9
5
1
11
10
12 13 14 15 16 17
18
19
F 53 0752 B
EN/6
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
3. Parts list
1 CD changer
2 Power supply cable
3 CD changer holder connection cable (4450 mm)*/****
4 CD changer holder connection cable (3000 mm)**/****
5 CD changer adapter cable****/******
6 CD changer coaxial cable (450 mm)***
7 Boot holder at the rear left
8 CD changer holder (2x)
9 Boot holder at the front left
10 Amplifier audio holder***
11 Cable tie (15x)
12 Philips screw M4x6 (4x)
13 Hexagonal screw M5x14 (8x)
14 Speed nut M5 (8x)
15 Hexagonal screw M6x10 (3x)
16 Shrink hose****/******
17 Socket casing (2x)
18 Speed nut M6 (4x)
19 Retaining clip*****
* Part only required for cars without an on-board monitor radio with a production date
after 10/00
** Part only required for cars with an on-board monitor radio with a production date
after 10/01
*** Part only required for cars with a DSP amplifier
**** Part not required for cars with a DSP amplifier
***** Part only required for cars with a Professional radio SA663 with a production date
before 03/01
****** Part not required for cars with a Professional radio SA663 with a production date
before 03/01
EN/7
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
4. Connection overview
Power supply cable
A
is
only
required if the black 3-pin socket casing for the CD changer power
supply is not tied back on the audio wiring harness
Control cable
B
is
only
required for cars without an on-board monitor and without a Professional
hi-fi system DSP amplifier
Item Description
Cable
colour
Connection location in the car
A Power supply cable
--- ----
A1
Black 1-pin plug casing
X6500
with
twin-lead terminal I-BUS
white/grey/
yellow
To standard audio wiring harness plug connector
X322
in the boot on the left side panel, black 12-pin socket
casing
X322B
,
PIN4
, white/grey/yellow cable
A2
Black 1-pin plug casing
X6501
with
twin lead terminal 30 A64
red/green To standard audio wiring harness plug connector
X322
in the boot on the left side panel, black 12-pin socket
casing
X322B
,
PIN1
, red/green cable
A3
Cable eyelet, 6 mm in diameter,
terminal 31
brown Earth post
X13016
in the boot on the left side panel
A4
Black 3-pin socket casing
---
Power supply connector
X18180
for CD changer in the
boot on the left
17
Black 1-pole socket casing
---
To the disconnected socket contacts from the standard
audio wiring harness plug connector
X322B
in the boot
on the left side panel
Item Description
Cable
colour
Connection location in the car
B Radio/CD changer control cable
--- ----
B1
Silver 10-pin socket casing
---
To silver 10-pin plug casing
E2
on the adapter cable or,
on cars with a Professional radio SA663 with a
production date before 03/01, to the black 17-pin radio
socket casing
B2
Black 6-pin socket casing
---
To the CD changer in the boot on the left
B
B1
B2
F 53 0799 B
EN/8
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
4. Connection overview
Control cable
C
is
only
required for cars with an on-board monitor and without a Professional
hi-fi system DSP amplifier
Coaxial cable
D
is
only
required for cars with a Professional hi-fi system DSP amplifier
Adapter cable
E
is
only
required for cars without a Professional hi-fi system DSP amplifier.
Adapter cable
E
is not required for cars with Radio Professional radio SA663 with a production
before 02/01.
Item Description
Cable
colour
Connection location in the car
C On-board monitor radio/CD changer
control cable
--- ----
C1
Silver 10-pin socket casing
---
To silver 10-pin control casing
E2
on the adapter cable
C2
Black 6-pin socket casing
---
To the CD changer in the boot on the left
Item Description
Cable
colour
Connection location in the car
D Coaxial cable
--- ----
D1
Angled coaxial socket casing
---
To the Professional hi-fi system DSP amplifier in the boot
on the left
D2
Coaxial socket casing
---
To the CD changer in the boot on the left
Item Description
Cable
colour
Connection location in the car
E Adapter cable
--- ----
E1
White 12-pin socket casing
---
To the new generation radio connection plug at the front
or the new generation on-board monitor radio at the rear
E2
Silver 10-pin plug casing
---
To silver 10-pin socket casing on the control cable
B
or
C
C
C2
C1
F 53 0800 B
D
D2
D1
F 53 0801 B
E
E1
E2
F 53 0802 B
EN/9
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
5. Installation and cabling diagram
0
The power supply wiring harness
A
, the control cable
B
, the control cable
C
, the coaxial cable
D
and the adapter cable
E
are to be installed as shown in the figure and secured with cable ties.
When installing the power supply wiring harness
A
start with branches
A1
and
A2
.
Branches
A1
,
A2
and
A3
to the left side panel in the boot
Branch
A4
to the CD changer in the boot on the left
Branch
B1 to the installation site of the radio / connect to branch E2
Branch B2 to the CD changer in the boot on the left
Connect branch C1 to branch E2
Branch C2 to the CD changer in the boot on the left
Branch D1 to the DSP amplifier in the boot on the left
Branch D2 to the CD changer in the boot on the left
Branch E1 to the new generation radio connection plug at the front or the new generation
on-board monitor connection plug in the boot on the left
Branch E2 to branch B1 or branch C1
B
E
C1
C
E
E1
B2
A1-A4
E2
B1
E1
E2
D1-D2
C2
F 53 0754 B
EN/10
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
6. To install audio module holder
(only required for cars without an audio module holder)
0
Place the audio amplifier holder (10) on the stud
bolt M6 (30) and secure it with two hexagonal nuts
M6 (18). Screw the hexagonal screw M6x10 (15)
into the thread M6 (31) in the rear closing panel.
0
Place two speed nuts M5 (14) on to the audio
amplifier holder (10).
0
Insert the holder for the boot at the rear left (7) and
secure it with two hexagonal screws M5x14 (13)
and one hexagonal screw M6x10 (15).
0
Place two speed nuts M5 (14) into the hole in the
holder for the boot at the rear left (7).
A
30
18
15
31
10
F 53 0755 B
14
10
F 53 0756 B
2
15
7
13
F 53 0757 B
7
14
14
F 53 0758 B
EN/11
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
6. To install audio module holder (only required for cars without an audio module holder)
0
On cars with a Professional hi-fi system DSP
amplifier, transceiver (permanent telephone) or
basic interface telephone (mobile), undo the two
hexagonal nuts M6 (18).
Insert the holder for the boot at the front left (9) and
secure it with the two existing hexagonal nuts M6
(18), two hexagonal screws M5x14 (13) and one
hexagonal screw M6x10 (15).
0
Place a speed nut M5 (14) on to the audio amplifier
holder (10), one speed nut M5 (14) on to the holder
for the boot at the rear left (7) and two speed nuts
M5 (14) on to the holder for the boot at the front left
(9).
15
13
9
18
F 53 0759 B
7
9
14
10
14
F 53 0760 B
EN/12
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
7. To install the CD changer (cars without an on-board monitor, without a DSP
amplifier and with Professional radio SA663 up to production date 03/01 only)
0
The installation of the power supply cable A
for the CD changer is only necessary, if the
black 3-pin socket casing X18180 on the
power supply for the CD changer is not tied
back near X322 on the audio wiring
harness.
0
Disconnect the white 12-pin plug connector X322.
Disconnect the existing socket contact from slot
PIN4, white/grey/yellow cable on the white 12-pin
socket casing X322B.
Connect branch A1, 1-pin socket contact, white/
grey/yellow cable on the power supply cable A to
the white 12-pin socket casing X322B in slot
PIN4.
Connect the supplied 1-pin black socket casing to
the disconnected socket contact and connect it to
branch A1, black 1-pin plug casing, white/grey/
yellow cable.
0
Disconnect the existing socket contact from slot
PIN1, red/green cable on the white 12-pin socket
casing X322B. Connect branch A2, 1-pin socket
contact, red/green cable on the power supply
cable A to the white 12-pin socket casing X322 in
slot PIN1.
Connect the supplied 1-pin black socket casing
on to the disconnected socket contact and
connect it to branch A2, black 1-pin plug casing,
red/green cable. Remove the left tail light.
0
Screw branch A3, cable eyelet, 6 mm in diameter,
brown cable on the power supply cable A, to earth
post X13016 in the boot at the rear left on the side
panel.
Lay branch A4, black 3-pin socket casing on the
power supply cable A, to the installation location of
the CD changer.
X322
X18180
F 53 0761 B
A1
X322
A
1
2
A1
PIN4
X322B
F 53 00762 B
1
A2
X322
A2
A
PIN1
2
X322B
F 53 0763 B
X13016
A3
A
A4
F 53 0764 B
EN/13
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 up to production date 03/01 only)
0
The installation of the control cable B for
the CD changer is only required, if the black
6-pin socket casing X18729 on the control
cable for the CD changer is not tied back
near the connection plug X322 on the audio
wiring harness.
0
Lay control cable B along the audio wiring harness
as follows.
Connect branch B1, silver 10-pin socket casing on
the control cable B to the black radio connection
plug in the centre console.
Lay control cable B from the radio (30) along the
centre console under the carpet parallel to the
audio wiring harness to the rear left door sill and
along the side panel to the installation site of the
CD changer (1).
0
Connect branch B1, silver 12-pin socket casing on
the control cable B to the black 17-pin socket
casing X18126 on the radio connection plug and
secure it with a retaining clip (19).
Connect socket casing X18126 to the radio (30).
0
Remove the three transport guard screws (30)
from the CD changer (1) and seal the apertures
with the adhesive discs supplied (adhesive discs
are supplied with the CD changer).
Remove the two covers (31) and set the
adjustment mechanism (32) with a flat screwdriver
to H (horizontal installation) and then re-affix both
covers (31).
X322
X18729
B
F 53 0765 B
30
B1
B
X18126
1
F 53 0767 B
19
B1
B
X18126
30
053 0134 B
V
H
V
H
1
32
30
31
31
F 39 0769 B
EN/14
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 up to production date 03/01 only)
0
Secure both CD changer holders (8) to the CD
changer (1) with four fillister head Philips screws
(12).
0
Connect branch A4, black 3-pin socket casing on
the power supply cable A or the standard power
supply plug X18180 to the plug casing on the
power supply connector (30) on the CD changer
(1).
Connect branch B2, black 6-pin socket casing on
the control cable B or the standard plug X18729 to
the plug casing (31) on the CD changer (1).
0
Insert the connected CD changer (1) with the fitted
retaining brackets into the shaft opening and
secure it with four hexagonal screws M5x14 (13).
1
8
8
12
12
12
12
F 53 0770 B
B2/X18729
31
30
A4/X18180
1
F 53 0771 B
13
1
13
F 53 0772 B
EN/15
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
8. To install the CD changer (cars without an on-board monitor, without a DSP
amplifier and with Professional radio SA663 after production date 04/01 only)
0
The installation of the power supply cable A
for the CD changer is only necessary, if the
black 3-pin socket casing X18180 on the
power supply for the CD changer is not tied
back near X322 on the audio wiring
harness.
0
Disconnect the white 12-pin plug connector X322.
Disconnect the existing socket contact from slot
PIN4, white/grey/yellow cable on the white 12-pin
socket casing X322B.
Connect branch A1, 1-pin socket contact, white/
grey/yellow cable on the power supply cable A to
the white 12-pin socket casing X322B in slot
PIN4.
Connect the supplied 1-pin black socket casing to
the disconnected socket contact and connect it to
branch A1, black 1-pin plug casing, white/grey/
yellow cable.
0
Disconnect the existing socket contact from slot
PIN1, red/green cable on the white 12-pin socket
casing X322B. Connect branch A2, 1-pin socket
contact, red/green cable on the power supply
cable A to the white 12-pin socket casing X322 in
slot PIN1.
Connect the supplied 1-pin black socket casing
on to the disconnected socket contact and
connect it to branch A2, black 1-pin plug casing,
red/green cable. Remove the left tail light.
0
Screw branch A3, cable eyelet, 6 mm in diameter,
brown cable on the power supply cable A, to earth
post X13016 in the boot at the rear left on the side
panel.
Lay branch A4, black 3-pin socket casing on the
power supply cable A, to the installation location of
the CD changer.
X322
X18180
F 53 0761 B
A1
X322
A
1
2
A1
PIN4
X322B
F 53 00762 B
1
A2
X322
A2
A
PIN1
2
X322B
F 53 0763 B
X13016
A3
A
A4
F 53 0764 B
EN/16
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
8. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 after production date 04/01 only)
0
Push the shrink hose (16) over branch E2, silver 10-pin plug casing on adapter cable E, and
connect branch B1, silver 10-pin socket casing on control cable B to it.
As you connect B1 to E2 ensure that it is correctly positioned, see figure.
All sharp metal and plastic detents are to be removed from plug connection B1 and E2 using
an angle cutter.
There must be no sharp edges or corners on plug connection B1 and E2.
Push the shrink hose (16) over the plug connection B1 and E2 and shrink it using a hot air
blower.
0
The installation of the control cable B for
the CD changer is only required, if the black
6-pin socket casing X18729 on the control
cable for the CD changer is not tied back
near the connection plug X322 on the audio
wiring harness.
0
Lay adapter cable E with control cable B along the
audio wiring harness as follows.
Connect branch E1, white 12-pin socket casing on
adapter cable E, to the new generation radio
connection plug in the centre console.
Lay control cable B from the radio (30) along the
centre console under the carpet parallel to the
audio wiring harness to the rear left door sill and
along the side panel to the installation site of the
CD changer (1).
X322
X18729
B
F 53 0765 B
B1
B1
E2
16
B1
E2
E2
F 53 0766 B
30
E1
B
X18126
1
E1
053 0135 B
EN/17
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
8. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 after production date 04/01 only)
0
Connect the white 12-pin socket casing E1 on
adapter cable E to the new generation radio
connection plug (30).
Connect the new generation radio connection
plug (30) and install the radio.
0
Remove the three transport guard screws (30)
from the CD changer (1) and seal the apertures
with the adhesive discs supplied (adhesive discs
are supplied with the CD changer).
Remove the two covers (31) and set the
adjustment mechanism (32) with a flat screwdriver
to H (horizontal installation) and then re-affix both
covers (31).
0
Secure both CD changer holders (8) to the CD
changer (1) with four fillister head Philips screws
(12).
0
Connect branch A4, black 3-pin socket casing on
the power supply cable A or the standard power
supply plug X18180 to the plug casing on the
power supply connector (30) on the CD changer
(1).
Connect branch B2, black 6-pin socket casing on
the control cable B or the standard plug X18729 to
the plug casing (31) on the CD changer (1).
E1
30
E
F 53 0768 B
V
H
V
H
1
32
30
31
31
F 39 0769 B
1
8
8
12
12
12
12
F 53 0770 B
B2/X18729
31
30
A4/X18180
1
F 53 0771 B
EN/18
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
8. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 after production date 04/01 only)
0
Insert the connected CD changer (1) with the fitted
retaining brackets into the shaft opening and
secure it with four hexagonal screws M5x14 (13).
13
1
13
F 53 0772 B
EN/19
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
9. To install the CD changer
(cars with an on-board monitor and without a DSP amplifier only)
0
The installation of the power supply cable A
for the CD changer is only necessary, if the
black 3-pin socket casing X18180 on the
power supply for the CD changer is not tied
back near X322 on the audio wiring
harness.
0
Disconnect the white 12-pin plug connector X322.
Disconnect the existing socket contact from slot
PIN4, white/grey/yellow cable on the white 12-pin
socket casing X322B.
Connect branch A1, 1-pin socket contact, white/
grey/yellow cable on the power supply cable A to
the white 12-pin socket casing X322B in slot
PIN4.
Connect the supplied 1-pin black socket casing to
the disconnected socket contact and connect it to
branch A1, black 1-pin plug casing, white/grey/
yellow cable.
0
Disconnect the existing socket contact from slot
PIN1, red/green cable on the white 12-pin socket
casing X322B. Connect branch A2, 1-pin socket
contact, red/green cable on the power supply
cable A to the white 12-pin socket casing X322 in
slot PIN1.
Connect the supplied 1-pin black socket casing
on to the disconnected socket contact and
connect it to branch A2, black 1-pin plug casing,
red/green cable. Remove the left tail light.
0
Screw branch A3, cable eyelet, 6 mm in diameter,
brown cable on the power supply cable A, to earth
post X13016 in the boot at the rear left on the side
panel.
Lay branch A4, black 3-pin socket casing on the
power supply cable A, to the installation location of
the CD changer.
X322
X18180
F 53 0773 B
A1
X322
A
1
2
A1
PIN4
X322B
F 53 00774 B
1
A2
X322
A2
A
PIN1
2
X322B
F 53 0775 B
X13016
A3
A
A4
F 53 0776 B
EN/20
Retrofit / Installation kit No. 65 12 0 029 883 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 576
9. To install the CD changer (cars with an on-board monitor and without a DSP amplifier only)
0
Push the shrink hose (16) over branch E2, silver 10-pin plug casing on adapter cable E, and
connect branch C1, silver 10-pin socket casing on control cable C to it.
As you connect C1 to E2 ensure that it is correctly positioned, see figure.
All sharp metal and plastic detents are to be removed from plug connection C1 and E2 using
an angle cutter.
There must be no sharp edges or corners on plug connection C1 and E2.
Push the shrink hose (16) over the plug connection C1 and E2 and shrink it using a hot air
blower.
0
The installation of the control cable C for
the CD changer is only required, if the black
6-pin socket casing X18729 on the control
cable for the CD changer is not tied back
near the connection plug X322 on the audio
wiring harness.
0
Install control cable C as follows:
Connect branch C1, silver 10-pin socket casing
on the control cable C to the black new generation
radio connection plug (30) on the on-board
monitor (31).
Lay control cable C from the on-board monitor (31)
along the audio wiring harness in the boot to the
installation site of the CD changer (1).
X322
X18729
C
F 53 0777 B
C1
C1
E2
16
C1
E2
E2
F 53 0778 B
C1
30
C
1
31
F 53 0779 B
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29

BMW 65 12 0 029 886 Installation Instructions Manual

BMW
Brand
BMW
Model
65 12 0 029 886
Category
Signal cables
Type
Installation Instructions Manual
This manual is also suitable for

BMW 65 12 0 029 886 is a CD changer installation kit designed specifically for BMW X5 (E53) vehicles with a production date before 10/01. It allows for the integration of a CD changer into your vehicle's audio system, providing you with convenient access to your music collection.

The kit includes all the necessary cables, connectors, and mounting hardware to ensure a seamless installation. Once installed, you can enjoy the convenience of controlling your CD changer through your vehicle's audio system, allowing you to change tracks, browse albums, and adjust volume with ease while keeping your hands on the wheel.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents