Paradyne Hotwire 7974-A2 User manual

HOTWIRE

r

M/SDSL

STANDALONE

TERMINATION UNITS

MODELS 7974-A2, 7975-A2,

AND 7976-A2

USER’S GUIDE

Document No. 7900-A2-GB21-00

August 2000

Printed on recycled paper

A

7900-A2-GB21-00

August 2000

Copyright E 2000 Paradyne Corporation.

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be copied or distributed,

transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form

or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the

express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation

reserves the right to revise this publication and to make changes from time to time in the contents hereof without

obligation of Paradyne Corporation to notify any person of such revision or changes.

Changes and enhancements to the product and to the information herein will be documented and issued as a new

release to this manual.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for any help needed. For

additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor

locations, or Paradyne worldwide office locations, use one of the following methods:

H Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty

at www.paradyne.com/warranty.)

H Telephone: Call our automated system to receive current information by fax or to speak with a company

representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them to Technical Publications,

Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to [email protected]. Include

the number and title of this document in your correspondence. Please include your name and phone number if you

are willing to provide additional clarification.

Trademarks

ACCULINK, COMSPHERE, FrameSaver, Hotwire, and NextEDGE are registered trademarks of Paradyne

Corporation. MVL, OpenLane, Performance Wizard, and TruePut are trademarks of Paradyne Corporation. All other

products and services mentioned herein are the trademarks, service marks, registered trademarks, or registered

service marks of their respective owners.

i

7900-A2-GB21-00

August 2000

Contents

About This Guide

H Document Purpose and Intended Audience vii. . . . . . . . . . . . . . . . . . . . . . . . .

H Document Summary vii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Product-Related Documents viii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 About the Hotwire Standalone Termination Unit

H M/SDSL Overview 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Hotwire Standalone Termination Unit Features 1-2. . . . . . . . . . . . . . . . . . . . . .

H Network Configuration 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Front Panel LED Status Indicators 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Rear Panel Interface Connections 1-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H SNMP Management Capabilities 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Management Information Base (MIB) Support 1-6. . . . . . . . . . . . . . . . . . .

SNMP Trap Support 1-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Using the Asynchronous Terminal Interface

H User Interface Access 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Communication Port Settings 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Initiating an ATI Session 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Menu Tree 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Screen Work Areas 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Navigating the Screens 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Keyboard Keys 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Screen Function Keys 2-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Switching Between Screen Work Areas 2-8. . . . . . . . . . . . . . . . . . . . . . . .

H Ending an ATI Session 2-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

ii

7900-A2-GB21-00

August 2000

3 Initial Startup and Configuration

H Overview 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Connecting Power 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting to an Optional External DC Power Source 3-2. . . . . . . . . . . .

H Connecting to the Network 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Connecting to a DTE 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Connecting to a System Terminal 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Entering Identity Information 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Choosing a Configuration Method 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Configuring the Unit Using the Configuration Menus 3-7. . . . . . . . . . . . . . . . .

H Accessing and Displaying Configuration Options 3-8. . . . . . . . . . . . . . . . . . . .

H Configuration Edit/Display 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Configuration Loader 3-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Saving Configuration Options 3-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Downloading Code 3-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Disabling AutoRate 3-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Resetting AutoRate 3-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 Configuring the Unit Using the Internal Switches

H Overview 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Configuring the Unit Using the Internal Switches 4-2. . . . . . . . . . . . . . . . . . . .

Switchpack Locations 4-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Switchpack Definitions for Model 7974 4-4. . . . . . . . . . . . . . . . . . . . . . . . .

Switchpack Definitions for Model 7975 4-6. . . . . . . . . . . . . . . . . . . . . . . . .

Switchpack Definitions for Model 7976 4-9. . . . . . . . . . . . . . . . . . . . . . . . .

5 IP Addressing

H Selecting an IP Addressing Scheme 5-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configurations Not Running IP Conservative Software 5-1. . . . . . . . . . .

All Configurations 5-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H IP Addressing Example 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

iii

7900-A2-GB21-00

August 2000

6 Security

H Overview 6-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H ATI Access Levels 6-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Creating a Login 6-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Deleting a Login 6-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Resetting the Unit’s COM Port or Factory Defaults 6-6. . . . . . . . . . . . . . . . . . .

H Controlling SNMP Access 6-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Assigning SNMP Community Names and Access Types 6-7. . . . . . . . . .

Limiting SNMP Access through the IP Addresses of the Managers 6-7.

7 Monitoring and Troubleshooting

H What to Monitor 7-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Viewing System and Test Status 7-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Health and Status Messages 7-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Self-Test Results Messages 7-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Test Status Messages 7-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Entry Response Messages 7-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Viewing Network Error Statistics 7-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Viewing Network Performance Statistics 7-11. . . . . . . . . . . . . . . . . . . . . . . . . . .

H Viewing DSX-1 Performance Statistics

(Model 7974) 7-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Viewing G.703 Performance Statistics

(Model 7976) 7-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Using the Display LEDs Screen 7-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Hotwire Standalone Termination Unit LEDs 7-18. . . . . . . . . . . . . . . . . . . . . . . . .

H Troubleshooting 7-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

iv

7900-A2-GB21-00

August 2000

8 Testing

H Accessing the Test Menu 8-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Running Network Tests 8-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Network Line Loopback 8-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Remote Network Send Line Loopback 8-5. . . . . . . . . . . . . . . . . . . . . . . . .

H DSX-1 Tests (Model 7974) 8-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Network Repeater Loopback (DSX-1) 8-7. . . . . . . . . . . . . . . . . . . . . . . . . .

DSX-1 DTE Loopback 8-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H SYNC Data Port Tests (Model 7975) 8-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Data Terminal Loopback 8-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Data Channel Loopback 8-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Send Remote Data Channel Loopback 8-12. . . . . . . . . . . . . . . . . . . . . . . . .

H G.703 Tests (Model 7976) 8-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Network Repeater Loopback (G.703) 8-14. . . . . . . . . . . . . . . . . . . . . . . . . .

G.703 DTE Loopback 8-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Device Tests 8-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lamp Test 8-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Ending an Active Test 8-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Telco-Initiated Tests (Model 7974) 8-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Telco-Initiated Line Loopback 8-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Telco-Initiated Payload Loopback 8-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Telco-Initiated Remote Line Loopback 8-19. . . . . . . . . . . . . . . . . . . . . . . . . .

A Configuration Options

H Overview A-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Network Interface Options Menu A-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H DSX-1 Interface Options for Model 7974 A-6. . . . . . . . . . . . . . . . . . . . . . . . . . .

H Synchronous Data Port Options for Model 7975 A-8. . . . . . . . . . . . . . . . . . . . .

H G.703 Interface Options for Model 7976 A-11. . . . . . . . . . . . . . . . . . . . . . . . . . . .

H System Options Menu A-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Communication Port A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Management and Communication Options Menu A-19. . . . . . . . . . . . . . . . . . . .

Telnet Session Options A-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Communication Protocol Options A-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General SNMP Management Options A-24. . . . . . . . . . . . . . . . . . . . . . . . . .

SNMP NMS Security Options A-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SNMP Traps Options A-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

v

7900-A2-GB21-00

August 2000

B Standards Compliance for SNMP Traps

H SNMP Traps B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H ifIndex Variable Binding B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H warmStart B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H authenticationFailure B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H linkUp and linkDown B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Enterprise-Specific Traps B-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C Cables and Pin Assignments

H Overview C-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H Power Input Connector C-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H COM Port Connector C-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H COM Port-to-PC Cable C-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H COM Port-to-LAN Adapter Cable C-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H DSX-1/G.703 Network Interface C-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H EIA-530-A Port C-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H EIA-530-A-to-X.21 Interface C-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H EIA-530-A-to-RS-449 Interface C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H EIA-530-A-to-V.35 Interface C-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H DSL Network Interface Cable C-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

D Technical Specifications

Glossary

Index

Contents

vi

7900-A2-GB21-00

August 2000

This page intentionally left blank.

vii

7900-A2-GB21-00

August 2000

About This Guide

Document Purpose and Intended Audience

This guide contains information needed to set up, configure, and operate the

Hotwire Multirate Symmetric Digital Subscriber Line (M/SDSL) Standalone

Termination Unit, Models 7974-A2, 7975-A2 and 7976-A2, and is intended for

installers and operators.

Document Summary

Section Description

Chapter 1 About the Hotwire Standalone Termination Unit. Describes

the unit’s features and capabilities.

Chapter 2 Using the Asynchronous Terminal Interface. Provides

instructions for accessing the user interface and navigating

through the screens.

Chapter 3 Initial Startup and Configuration. Provides procedures for

setting up the user interface and for configuring the unit

using the asynchronous terminal interface.

Chapter 4 Configuring the Unit Using the Internal Switches. Provides

procedures for configuring the unit using the internal

switches instead of the asynchronous terminal interface.

Chapter 5 IP Addressing. Provides information and examples

regarding IP addresses.

Chapter 6 Security. Presents procedures for creating a login, setting

the effective access levels, and controlling SNMP access.

Chapter 7 Monitoring and Troubleshooting. Describes using the LEDs,

status messages, and network statistics to monitor the unit

and detect and correct problems.

Chapter 8 Testing. Provides information about available tests and test

setup.

About This Guide

viii

7900-A2-GB21-00

August 2000

Section Description

Appendix A Configuration Options. Contains all configuration options,

possible settings, and default settings.

Appendix B Standards Compliance for SNMP Traps. Contains SNMP

trap compliance information.

Appendix C Cables and Pin Assignments. Contains connector and

interface information.

Appendix D Technical Specifications. Contains physical and regulatory

specifications, network and port interfaces, power

consumption values, and accessory part numbers.

Glossary Defines acronyms and terms used in this document.

Index Lists key terms, acronyms, concepts, and sections in

alphabetical order.

Product-Related Documents

Document Number Document Title

7900-A2-GN11 Hotwire M/SDSL Standalone Termination Units,

Models 7974-A2, 7975-A2, and 7976-A2, Installation

Instructions

8700-A2-GB20 Hotwire M/SDSL and HDSL2 Termination Units,

Models 8747, 8777, and 8779, User’s Guide

8700-A2-GB25 Hotwire M/SDSL and M/HDSL Termination Units,

Models 8775 and 8785, User’s Guide

Contact your sales or service representative to order additional product

documentation.

Paradyne documents are also available on the World Wide Web at

www.paradyne.com. Select Library → Technical Manuals.

1-1

7900-A2-GB21-00

August 2000

About the Hotwire Standalone

Termination Unit

1

M/SDSL Overview

Hotwirer Multirate Symmetric Digital Subscriber Line (M/SDSL) products

maximize customer service areas by varying the DSL line rate. This ensures

symmetric DSL connectivity over a wide range of telephone line distances and

transmission line qualities.

Hotwire products support autorate. Units first synchronize to the highest line rate

that the 2-wire loop supports, and then automatically configure to the highest

multiple of 64 kbps supported by that line rate. Eight line rates are available. At all

rates, a 16 kbps management channel is available, which enables functions such

as firmware downloads to remote units. Units can also be configured manually to

full or fractional T1 or E1 rates.

Hotwire products transport data over a 2-wire (M/SDSL) full-duplex circuit over

varying distances based on the conditions of the loop. Using 24 AWG cable,

M/SDSL products have a loop reach greater than 14,000 feet (4.6 km) at

2.048 Mbps.

About the Hotwire Standalone Termination Unit

1-2

7900-A2-GB21-00

August 2000

Hotwire Standalone Termination Unit Features

The Hotwire Standalone Termination Unit is an endpoint for the chassis-mounted

Hotwire 877x Termination Unit housed in the Hotwire 8600 Series or 8800 Series

Digital Subscriber Line Access Multiplexer (DSLAM).

Two Hotwire Standalone Termination Units can also be configured to operate in a

central office line termination unit (LTU) to customer premises network

termination unit (NTU) environment.

The termination unit offers these standard features:

H Embedded Operations Channel (EOC). Provides remote SNMP Traps,

Telnet session capability over the M/SDSL link, and download capabilities.

H Asynchronous Terminal Interface (ATI). Provides a menu-driven

VT100-compatible terminal interface for configuring and managing the

termination unit locally or remotely by Telnet session.

H Local Management (standalone unit). Provides local management using a:

— Terminal or equivalent through the COM port of the unit

— Telnet through the COM port of the unit

H Remote Management (DSLAM card). Provides remote management using:

— VT100-compatible terminal or PC via the Management Serial port of the

DSLAM

— NMS through the MCC port of the DSLAM

— Telnet over the EOC

H Alarm Indication. Provides front panel status LEDs.

H Diagnostic Testing. Provides the capability to diagnose device and network

problems and perform digital loopbacks, pattern tests, and self-test.

H Device and Performance Monitoring. Provides the capability of tracking

and evaluating the unit’s operation, including health and status, and error-rate

monitoring.

H SNMP (Simple Network Management Protocol) Management. Provides

network management via an industry-standard SNMP management system.

H Automatic Configuration Capability. Simply connecting the units to the line

automatically configures the customer for the maximum data rate supported

by the local loop. Units can also be configured at fixed line speeds to achieve

maximum distances.

About the Hotwire Standalone Termination Unit

1-3

7900-A2-GB21-00

August 2000

Network Configuration

Figure 1-1 shows a network application using a termination unit in a central office

(CO). In this configuration, a frame relay switch and a router are connected

through the termination unit to partner units supporting a host or router, and

frame relay encapsulated or unframed data. The figure also shows a

standalone-to-standalone configuration. Supported standalone-to-standalone

configurations are shown in Table 1-1.

Table 1-1. Supported Standalone NTU/LTU Combinations

NTU (CP)

LTU (CO):

DSX-1 Synchronous

G.703

Framed

G.703

Unframed

DSX-1

n n

Not Supported Not Supported

Synchronous Not Supported

n

Not Supported

n

G.703 Framed Not Supported

n n

Not Supported

G.703 Unframed Not Supported

n

Not Supported

n

n = Supported

Frame

Relay

Switch

Router

T1 Host

(Frame Relay

Encapsulated

Data)

00-16486-01

Router

(Frame Relay

Encapsulated

Data)

Router

877x Termination Unit

in DSLAM

CO Site

797x

797x 797x

CP

NTU

CO Site

LTU

DSL

Customer Premises (CP)

DSL

G.703, DSX-1 or V.35

DSL

Figure 1-1. Sample Configurations

About the Hotwire Standalone Termination Unit

1-4

7900-A2-GB21-00

August 2000

Front Panel LED Status Indicators

Figures 1-2 through 1-4 show the front panel of the Hotwire Standalone

Termination Units. For more information on front panel LEDs, refer to Chapter 7,

Monitoring and Troubleshooting.

POWER

ALARM

TEST

DSL

DSX-1

98-16116

7974 M/SDSL

TM

Figure 1-2. Hotwire DSX-1 Interface Termination Unit Front Panel

POWER

ALARM

TEST

DSL

DTE

98-15856

7975 M/SDSL

TM

Figure 1-3. Hotwire Synchronous Interface Termination Unit Front Panel

POWER

ALARM

TEST

DSL

G.703

98-16003

7976 M/SDSL

TM

Figure 1-4. Hotwire G.703 Interface Termination Unit Front Panel

About the Hotwire Standalone Termination Unit

1-5

7900-A2-GB21-00

August 2000

Rear Panel Interface Connections

Figures 1-5 through 1-7 show the physical interfaces of the termination units.

POWER DSLCOM DSX-1

98-16117

O

I

Figure 1-5. Hotwire DSX-1 Interface Termination Unit Rear Panel

POWER

DSLCOM

98-15880

PORT

O

I

Figure 1-6. Hotwire Synchronous Interface Termination Unit Rear Panel

POWER DSLCOM

TX RX

G.703

75Ω120Ω

98-16005

O

I

Figure 1-7. Hotwire G.703 Interface Termination Unit Rear Panel

About the Hotwire Standalone Termination Unit

1-6

7900-A2-GB21-00

August 2000

SNMP Management Capabilities

The Hotwire 797x Standalone Termination Units support SNMP Version 1, and

can be managed by any industry-standard SNMP manager and accessed using

SNMP by external SNMP managers.

Management Information Base (MIB) Support

For a detailed description of the supported MIBs, visit Paradyne’s Web site at

www.paradyne.com. Select Technical Support → MIBs.

The following MIBs are supported:

H MIB II (RFC 1213 and RFC 1573) – Defines the general objects for use with

a network management protocol in TCP/IP internets and provides general

information about the unit. MIB II is backward-compatible with MIB I.

H DS1/E1 MIB (RFC 1406) – Models 7974 and 7976. Reports the performance

status of the DSX-1 or G.703 interface and supports the features found on

the DSX-1 or G.703 Performance Statistics screen.

H RS-232-Like MIB (RFC 1659) – Defines objects for managing RS-232-type

interfaces (e.g., V.35, RS-422, RS-423, etc.) and supports the synchronous

data port on the DSU.

H Paradyne Enterprise MIB – Supports configuration, status, statistics, and

tests.

About the Hotwire Standalone Termination Unit

1-7

7900-A2-GB21-00

August 2000

SNMP Trap Support

Hotwire 797x Standalone Termination Units support traps as defined in

RFC 1215.

Figure 1-8 illustrates a typical DSL SNMP configuration. Figure 1-9 illustrates an

DSL SNMP configuration connected directly to the Communications Port. Refer

to Chapter 5, IP Addressing and Appendix B, Standards Compliance for SNMP

Traps.

00-16487-01

DSLAM

Network

797x

AC

INPUT

AC

48VDC CLASS 2 OR

LIMITED PWR SOURCE

RTN48V

AAB B

T5A

2

46

A

B

.

3

.

1

2

POSITION

STACK

ALM

A

IN

B

DC FUSES

T4A, MIN. 48V

5

DC PWR

FAN

OUT SERIAL

MCC 1

3

1

2

3

SYSTEM

OK

Alrm

Test

250V

SYSTEM

OK

Alrm

T

est

1

2

3

4

G.703 ALR

M

D

SL PO

RT

LINK-UP

1

2

3

4

SYSTEM

OK

Alrm

Test

1

2

3

4

G.703 A

LRM

D

SL P

ORT

LINK-UP

SDSL

8715

1

2

3

4

Router

SNMP NMS

Ethernet

Interface

DSL

EOC

Data

Operation, Maintenance

and Provisioning Center

Ethernet

LAN

1

2

3

4

G.703 ALRM

D

SL PO

RT

LINK-UP

1

2

3

4

877x

Figure 1-8. DSL SNMP Configuration

00-16488-01

797x

SNMP NMS

DSL

EOC

Router

797x

COM

Figure 1-9. DSL Local SNMP Configuration

About the Hotwire Standalone Termination Unit

1-8

7900-A2-GB21-00

August 2000

This page intentionally left blank.

2-1

7900-A2-GB21-00

August 2000

Using the Asynchronous Terminal

Interface

2

User Interface Access

You can communicate with the Hotwire Standalone Termination Unit with an

asynchronous terminal interface (ATI) using one of the following methods:

H Direct connection through the COM port of the standalone unit or through the

serial port of the DSLAM management card.

H Telnet session through the Embedded Operations Channel (EOC).

NOTE:

Only one terminal interface session can be active at a time, and another

user’s session cannot be forced to end. To automatically log out a user due to

inactivity, enable the Inactivity Timeout option (see Table A-9, Telnet Session

Options, in Appendix A, Configuration Options).

Security can limit ATI access several ways. To limit user access or set up login

IDs, refer to Chapter 6, Security.

Communication Port Settings

Ensure that the device you connect communicates using these settings:

H Data rate set to 9.6 kbps.

H Character length set to 8.

H Parity set to None.

H Stop Bits set to 1.

Using the Asynchronous Terminal Interface

2-2

7900-A2-GB21-00

August 2000

Initiating an ATI Session

The Main Menu screen is displayed on the screen unless a login ID and

password is required or the ATI is already in use.

If the ATI is already in use, you will see:

H A connection refused or connection failed message (if you are

using a Telnet session), or

H The IP address of the other user (if you are using the Management Serial

port).

If security is enabled on the unit and you used Telnet to access it directly (you did

not log in through the DSLAM management card), the system prompts you for a

login ID and password.

Login Hotwire

Model: 797x

LOGIN

Login ID:

Enter Password:

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Ctrl-a to access these functions E

xit

Page is loading ...

Paradyne Hotwire 7974-A2, Hotwire 7974, Hotwire 7975, Hotwire 7975-A2, Hotwire 7976, Hotwire 7976-A2 User manual

Related papers

Other documents