2. Durabook
  3. R11
R11

Durabook R11 User manual

  • Hello! I've reviewed the R11 HF RFID expansion module user manual. This document provides detailed instructions for installing the RFID module into your R11 rugged tablet, including steps on removing the battery, assembling the components, and securing the screws with correct torque. I am ready to answer any questions you have about the installation process or the module itself.
  • What should I do if any items are damaged?
    What should I remove before installing the expansion module?
    What is the torque for bracket to lower case screws?
©2022 Twinhead International Corp and/or its affiliates. All rights reserved.
1
R11 Rugged Tablet
Expansion Modules
HF RFID
P/N: 62+030990+50
Expansion Modules_ HF RFID
2
Package Contents
If any of following items is damaged, please contact your retailer.
RFID module cover
(with pre-installed HF RFID
board)
Expansion sponge
RFID module bracket
Gasket
Sponges
RFID expansion board
Expansion FFC
Rubbers
Screws
HF RFID Module Screws
Screw Name
Quantity
Torque
ISOT-M2.0X4L
2 (bracket to lower
case)
2.0 ±0.3 Kgf-cm
ISOT-M2.6X4L
2 (expansion board
to bracket)
2.0 ±0.3 Kgf-cm
M2.6X6L
& O RING
4 (cover to lower
case)
2.5 ±0.3 Kgf-cm
NOTE
The pictures are for reference only, actual items may slightly differ.
Expansion Modules_ HF RFID
3
Installation
This section will guide you on how to install the expansion modules to your tablet
PC.
Note: Make sure to remove the battery before installing any type of expansion
modules. For more information on how to remove/install the battery, please refer
to the tablet PC service guide.
Installing the HF RFID Module
To install the HF RFID module, follow the steps below:
1. Remove the screw securing the mylar on the DDR door.
2. Remove the mylars from the DDR door.
Expansion Modules_ HF RFID
4
3. Attach the expansion sponge to the DDR door. Then install the sponges onto
the screw holes.
4. Connect the expansion FFC to the mainboard connector. Then secure the
latch.
5. Route the expansion FFC through the opening on the RFID module bracket.
Then, by aligning with the screw holes, install the bracket onto its slot on the
lower case.
Expansion Modules_ HF RFID
5
6. Attach the 2 screws to secure the RFID module bracket to the lower case.
7. Connect the expansion FFC to the RFID expansion board connector. Then
secure the latch.
8. Attach the tape to secure the expansion FFC in place.
Expansion Modules_ HF RFID
6
9. Flip the RFID expansion board. Then, by aligning with the screw holes, install
the RFID expansion board onto its slot on the RFID module bracket.
10. Attach the 2 screws to secure the RFID expansion board to the bracket.
11. By aligning with the screw holes, place the gasket onto the installed bracket.
Expansion Modules_ HF RFID
7
12. Attach the rubbers onto their respective slots on the RFID module bracket.
Make sure that those rubbers are properly attached at the designated slots
(alignment marked by dotted red lines) as shown in below illustration.
13. Connect the RFID module FPC to the RFID expansion board connector. Then
secure the latch.
14. Attach the tape to secure the RFID module FPC in place.
Expansion Modules_ HF RFID
8
15. By aligning with the screw holes, place the RFID module cover (with the pre-
installed HF RFID board) onto the installed gasket.
16. Attach the 4 screws to secure the RFID module cover to the lower case.
17. Install the battery.
Expansion Modules_ HF RFID
9
HF RFID Module Screws
Screw Name
Quantity
Torque
ISOT-M2.0X4L
2 (bracket to lower
case)
2.0 ±0.3 Kgf-cm
ISOT-M2.6X4L
2 (expansion board
to bracket)
2.0 ±0.3 Kgf-cm
M2.6X6L
& O RING
4 (cover to lower
case)
2.5 ±0.3 Kgf-cm
Twinhead International Corp.
11F, No.550, Ruiguang Rd., Neihu, Taipei 11492, Taiwan, R.O.C.
/