2. Industrial & lab equipment
  3. Electrical equipment & supplies
  4. Wire raceways conduits
  5. Cable trays
  6. MOUNTUP
  7. MU9007

MOUNTUP MU9007 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the MOUNTUP MU9007 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Cable Concealer Raceway
Installation Guide
Package Contents
Please refer to the diagram below for instructions on how
to use each connector and select your desired mounting
method.
CONNECTORS INSTRUCTION
WARNING
Outside connector:
Used for turning at
extermal corners.
Flat connector:
90° bend angle for
flat surface
Cable Raceway
T-fitting:
Used for T-shaped
corners
Coupling:
Used to connect 2 race-
ways to increase the
length at internal corners.
Inside connector:
Used for turning at
internal corners.
Cable Raceway Flat Connector
T-Fitting  
Double-Sided Tape Concrete Anchor Lag Screws
Coupling
Inside Connector Outside Connector

    
  

plan your installation well in advance of installation to
avoid removing and reinstalling the cable raceway. If

bottom of the raceway by heating it with a blower (not
too high a temperature is recommended) and then
gently peel it off.


your hands because of the sharp edges of the cut
cable raceway.



sided tape.
4. Use appropriate safety equipment when using cable
raceways. This product should not be used with
uninsulated or exposed wires.
5. It cannot be used to extend hard-wired (permanent)
wires or to twist cables or wires into loops.

via Amazon.
-
ing hazard if swallowed.


do not return the damaged item to your dealer; please
contact our customer service team. Never use damaged
parts!

Option 1: Install with tape (Not suitable for uneven surface)
Option 2: Install with screws (Only for solid concrete walls)
Raceway On the Wall
the Cables
9. Install Connectors & Covers
Raceway
2. Measure the Distance
4. 
Remove the Protectibe film


determine the number of cable raceways
needed and the number of connectors of
each type. Refer to the diagram at left to
determine the exact spacing of each connec-

each side raceway for each outside (or flat)


mm) for connectors at both ends such as

If one of the raceways exceeds the required
Cut the channel
smoothly and evenly downwards with a hand

Remove the protective film from the tape
behind the raceway.
Fix the bottom of the raceway to the wall
-
nel firmly against the walI to ensure it
adheres to the waII snugly.

sure they are not twisted or overlapped.
the Cables

sure they are not twisted or overlapped.

-

cable trough cover of the other raceway until
the installation is complete.
Place the raceway horizontally or vertically


guide to ensure that the raceway is parallel
or perpendicular to the floor or wall.
Wipe clean the wall surface.
Wall Surface
4. Do the 
Place the raceway horizontally or vertically


guide to ensure that the raceway is parallel
or perpendicular to the floor or wall.



raceway.
Remove the raceway and clean the dust on it.

hole. WARNING: Concrete anchors are for

drywall.

insert the lag screw through the raceway into
the anchor and tighten with a screwdriver.
Place the raceway against the wall according




drill.
5. Remove the Cover
Remove the cable raceway cover plate
carefully and do not deform the cover plate
so as not to affect the subsequent installa-
tion.
5. Remove the Cover

7. Drill the Hole
Clean the Dust
9. Insert Concrete Anchor
Tighten the Screws
Remove the cable raceway cover plate
carefully and do not deform the cover plate
so as not to affect the subsequent installa-
tion.

(50 mm)
Raceway
If one of the raceways exceeds the required
Cut the channel
smoothly and evenly downwards with a hand


 







2. Measure the Distance


determine the number of cable raceways
needed and the number of connectors of
each type. Refer to the diagram at left to
determine the exact spacing of each connec-

each side raceway for each outside (or flat)


mm) for connectors at both ends such as

Wipe clean the wall surface.
Wall Surface

 









-

cable trough cover of the other raceway until
the installation is complete.



Deep
Bit
/