LXE 8650A378BTBOHCHGRWW User manual

Brand: LXE

Model: 8650A378BTBOHCHGRWW

Type: User manual

This manual is also suitable for

Bluetooth Ring Scanner

Battery Charger User’s Guide

Models 8650A380SINGLECHGRWWS and 8650A378BTBOHCHGRWW

For Use with LXE (8650A376BTBOHBATTERY) Lithium Ion Battery Packs

E-EQ-BRSCHGROGWW-B

Notices

LXE Inc. reserves the right to make improvements or changes in the products described in this manual at any time without notice. While

reasonable efforts have been made in the preparation of this document to assure its accuracy, LXE assumes no liability resulting from any errors

or omissions in this document, or from the use of the information contained herein. Further, LXE Incorporated, reserves the right to revise this

publication and to make changes to it from time to time without any obligation to notify any person or organization of such revision or changes.

This manual is copyrighted. All rights are reserved. This document may not, in whole or in part, be copied, photocopied, reproduced, translated or

reduced to any electronic medium or machine-readable form without prior consent, in writing, from LXE Inc. Further, LXE Incorporated,

reserves the right to revise this publication and to make changes to it from time to time without any obligation to notify any person or

organization of such revision or changes.

125 Technology Parkway, Norcross, GA 30092, U.S.A. (770) 447-4224

LXE is a registered trademark of LXE Inc. All other brand or product names are trademarks or registered trademarks of their respective

reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated." applies.

FCC Information:

This device complies with FCC Rules, part 15. Operation is subject to the following conditions:

1. This device may not cause harmful interference

and

2. This device must accept any interference that may be received, including interference that may cause undesired operation.

Warning!

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Changes or modifications to this device not expressly approved by LXE Inc., could void the user’s authority to operate this equipment.

EMC Directive Requirements:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take

adequate measures.

Industry Canada:

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouiller du Canada.

Le present appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux appareils numeriques de le Classe A

préscrites dans le Reglement sur le brouillage radioélectrique édits par le ministere des Communications du Canada.

Important: This symbol is placed on the product to remind users to dispose of Waste Electrical and Electronic Equipment

(WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product can be recycled, reclaimed and re-used when

properly discarded. Do not discard labeled units with trash. For information about proper disposal, contact LXE through your

local sales representative, or visit www lxe com.

Initial Release May 2008

Revision Notice

Important Safety Warnings

– Save These Instructions

Added Warnings for specific battery pack and AC adapter.

Installation and Operation Added Warnings for specific battery pack and AC adapter.

IMPORTANT SAFETY WARNINGS US

SAVE THESE INSTRUCTIONS

This document contains important safety and operating instructions for the LXE Bluetooth Ring Scanner Battery

Single-bay Charger or Multi-Charger. Please read all instructions and cautionary markings on the charger itself

before putting the unit into service.

Safety Alert Symbols

This symbol is used to call your attention to instructions concerning your personal safety. Watch for

this symbol – it will alert you to important safety precautions that must be observed to avoid death,

personal injury or property damage. Follow the instructions after the warning symbol and be alert to

the possibility of personal injury or death.

These signal words provide users with information about the seriousness of the hazard involved:

DANGER WARNING CAUTION

Indicates imminent hazards

which, if not avoided, WILL

result in severe personal injury

or death.

Indicates potential hazards

which, if not avoided, COULD

result in severe personal injury

or death.

Indicates hazards or unsafe practices which,

if not avoided, COULD result in minor or

moderate personal injury or property

damage.

Safety Instructions

Setting up the Bluetooth Ring Scanner Battery Single-bay Charger or Multi-Charger

Locate or orient the AC cord so that it will not be stepped on, tripped over or subjected to damage or stress.

Charge only LXE (8650A376BTBOHBATTERY) Rechargeable Lithium Ion Battery Packs in these chargers. Other

batteries or battery packs may burst causing injury or property damage.

Operating the Battery Chargers

Only users who have read and understand all operating instructions are qualified to operate the Bluetooth Ring

Scanner Battery Single-bay or Multi-Charger. Failure to read, understand and follow safety instructions may result

in injury or death.

Keep the chargers away from any heat source. Excessive internal heating can ruin the chargers.

Use care when inserting battery. Do not "slam" or slide the battery into the pocket, this could damage the chargers.

Keep dirt and foreign objects out of the battery pocket. Do not short circuit any of the contacts in the battery pocket,

this could result in injury or property damage.

Do not operate the charger if it has been dropped or damaged in any way. Return the charger to LXE.

Storing the Bluetooth Ring Scanner Battery Single-bay Charger or Multi-Charger

Disconnect charger by pulling the plug; not the cord.

Maintaining the Bluetooth Ring Scanner Battery Single-bay Charger or Multi-Charger

Service should be performed by trained persons only. Return the chargers to LXE.

Caring for Batteries

Do not dispose of batteries into a fire. Burning will generate hazardous vapors and may cause the battery to explode.

Failure to observe this warning may result in injury from inhalation of vapors or burns from flying debris.

Do not immerse batteries in water or any other liquid. If batteries are immersed, contact LXE.

Do not disassemble or perform modifications to the battery. There are no user serviceable components in the battery.

Do not place battery into pocket or toolbox with conductive objects (coins, keys, tools, etc.).

A battery placed on damp ground or grass could be electrically shorted. Lay the battery down flat when not in use.

Do not store batteries above 140°F (60°C) for extended periods.

Failure to observe these warnings could result in injury or damage to the battery from rapid discharge of energy or

overheating of the battery.

Electrical Shock Hazards

The following precautions should be observed to avoid the risk of electrical shock hazards associated with charging

batteries:

The Bluetooth Ring Scanner Battery Single-bay Charger or Multi-Charger have been designed for indoor use only.

Do not operate outdoors or in extremely high humidity environments. Do not expose chargers to rain, snow or wet

conditions.

Unplug the chargers from power source before cleaning. Use only mild detergent with a slightly damp cloth to clean

the outside of the chargers. Do not use solvents or flammable cleaners. Allow the case to dry fully before using

again.

Use of attachments or accessories not recommended by LXE could result in fire, electric shock or injury.

These appliances must be properly grounded. If they should malfunction or break down, grounding provides a path

of least resistance for electric current to reduce the risk of electric shock. These appliances are equipped with a cord

having an equipment grounding conductor and ground outlet that is properly installed and grounded in accordance

with all local codes and ordinances. Do not operate the chargers with a damaged AC cord or plug. LXE does not

recommend the use of any extension cord with the Bluetooth Ring Scanner Battery Single-bay Charger or Multi-

Charger.

The Bluetooth Ring Scanner Battery Single-bay Charger or Multi-Charger have been designed for use on a nominal

100 or 120 volt or nominal 220 or 240 volt circuit and have a grounding attachment plug. The plug is an IEC

configuration that is appropriate for your country and regulations. Make sure that the appliance is connected to an

outlet having a configuration similar to the plug. No adapter should be used with these appliances. Improper

connection of the equipment-grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.

Do not modify the plug provided with the appliances. If the plug will not fit in the outlet, have a proper outlet

installed by a qualified electrician.

Do not disassemble the Bluetooth Ring Scanner Battery Single-bay Charger or Multi-Charger. They contain no user

serviceable parts.

Warning: The Bluetooth Ring Scanner Multi-bay Charger is to be used to charge an I.T.E.

Recognized Battery pack manufactured by Helix Co., Ltd. (Model: HNP-40, LXE,

P/N 161987-0001, rating 3.7V, 750mAh). Charging any other type of battery pack

in the Bluetooth Ring Scanner Multi-bay charger is prohibited.

Warning: Use the provided AC power supply, only, with the Bluetooth Ring Scanner Multi-

bay Charger. Using any other type of AC power supply is prohibited.

E-EQ-BRSCHGROGWW-B Bluetooth Ring Scanner Battery Charger User’s Guide

Table of Contents

INTRODUCTION 1

Purpose of this Manual.............................................................................................1

Quick Start.................................................................................................................1

Intended Use .............................................................................................................

Multi-Charger.............................................................................................................2

Multi-charger Footprint.............................................................................................3

Single-bay Charger...................................................................................................3

Battery Well...............................................................................................................4

Rechargeable Lithium Ion Battery Pack .................................................................5

Getting Help...............................................................................................................6

Accessories...............................................................................................................................6

INSTALLATION AND OPERATION 7

Overview....................................................................................................................7

Normal Operations....................................................................................................................7

Using the Battery Charging Pocket ..........................................................................................8

Inserting the Battery Pack ..................................................................................................................8

Removing the Battery Pack................................................................................................................8

Progress Monitoring.................................................................................................9

Charge Timers ..........................................................................................................................9

Multi-charger......................................................................................................................................9

Single-bay Charger.............................................................................................................................9

Interpreting the Single-Bay Charger LED................................................................................9

RED....................................................................................................................................................9

GREEN...............................................................................................................................................9

Interpreting the Multi-charger LEDs......................................................................................10

RED - on any pocket ........................................................................................................................10

GREEN - on any pocket...................................................................................................................10

Amber - on any pocket.....................................................................................................................10

NO LIGHT - on a pocket..................................................................................................................10

NO LIGHT - on every pocket...........................................................................................................10

Troubleshooting......................................................................................................

Maintenance............................................................................................................................12

Storage....................................................................................................................................

Service ....................................................................................................................................

TECHNICAL SPECIFICATIONS 13

Operating Temperature Ranges ............................................................................13

ii Table of Contents

Bluetooth Ring Scanner Battery Charger User’s Guide E-EQ-BRSCHGROGWW-B

Multi-Charger.........................................................................................................................13

Single-bay Charger.................................................................................................................

Electrical..................................................................................................................

Physical Dimensions..............................................................................................

Illustrations

Figure 1 Bluetooth Ring Scanner Battery Multi-Charger .................................................................................2

Figure 2 AC Power Supply, Multi-charger.......................................................................................................2

Figure 3 Multi-charger Footprint and Mounting Hole Locations......................................................................3

Figure 4 Bluetooth Ring Scanner Battery Single-bay Charger.........................................................................3

Figure 5 Battery Pockets...................................................................................................................................4

Figure 6 Lithium Ion Battery Pack Charging Contacts.....................................................................................5

Figure 7 Lithium Ion Battery Pack Label..........................................................................................................5

Figure 8 Interpreting the LEDs.......................................................................................................................10

E-EQ-BRSCHGROGWW-B Bluetooth Ring Scanner Battery Charger User’s Guide

Introduction

Purpose of this Manual

This user’s guide is intended to familiarize the user with the safety and operating instructions

necessary to use the Bluetooth Ring Scanner Battery Single Charger or Multi-Charger ( Model

8650A378BTBOHCHGRWW / 8650A380SINGLECHGRWW ) to charge the LXE Rechargeable

Bluetooth Ring Scanner Lithium Ion Battery (LXE Part No. 8650A376BTBOHBATTERY).

This guide should be readily available to all users and maintenance personnel using these chargers.

Quick Start

This guide provides the following instructions for operating the Bluetooth Ring Scanner Battery

Chargers.

• Setting up the Single-bay Charger

• Setting up the Multi-Charger

• Inserting the Battery Pack(s)

• Interpreting the LEDs

Note: Store the chargers in a cool, dry place.

Intended Use

The LXE Bluetooth Ring Scanner Battery Multi-Charger is designed to simultaneously charge up

to eight Rechargeable Lithium Ion Battery Packs in less than three hours, depending upon battery

pack temperature and conditions

The LXE Bluetooth Ring Scanner Battery Single Charger is designed to charge one Rechargeable

Lithium Ion Battery Pack in less than three hours, depending upon battery pack temperature and

conditions

The chargers should be located in an area where they:

Ensure that the location you choose:

• Is well ventilated.

• Is protected from moving objects in high traffic areas.

• Has enough clearance to allow easy access to the charging bays on top and the power port

at the back of the device.

• Is protected from rain, dust or inclement weather.

2 Multi-Charger

Bluetooth Ring Scanner Battery Charger User’s Guide E-EQ-BRSCHGROGWW-B

Multi-Charger

Figure 1 Bluetooth Ring Scanner Battery Multi-Charger

1 Power Cable Connection Location 3 LED Indicator

2 Battery Charging Pocket 4 LED Function

1. Place the multi-charger on a horizontal, hard surface or fasten securely to a wall using the

mounting holes (see Multicharger Footprint). Mounting hardware is not supplied by LXE.

2. Plug the 2 prong end of the power cord into a properly grounded AC outlet. Locate or orient

the AC cord so that it will not be stepped on, tripped over or subjected to damage or stress.

Figure 2 AC Power Supply, Multi-charger

3. Plug the multi-charger end of the power cord into the power port on the back of the device.

4. On initial power-up, LEDs light up for a few seconds.

The external power supply for the multi-charger is shipped with the multi-charger. If there is no

AC cable, please contact your LXE representative. The multi-charger power supply is intended for

use with the Bluetooth Ring Scanner Battery Multi-charger only.

Multi-charger Footprint 3

E-EQ-BRSCHGROGWW-A Bluetooth Ring Scanner Battery Charger User’s Guide

Multi-charger Footprint

Not To Scale

Figure 3 Multi-charger Footprint and Mounting Hole Locations

Single-bay Charger

Figure 4 Bluetooth Ring Scanner Battery Single-bay Charger

1 Battery Charging Pocket 3 Power Connector Location

2 Power LED Indicator 4 Single-bay Charger Power plug

The charger plug mounts the single-bay charger to an AC outlet.

1. Connect the power plug to the single-bay charger.

2. Insert the power plug into a properly grounded outlet.

4 Battery Well

Bluetooth Ring Scanner Battery Charger User’s Guide E-EQ-BRSCHGROGWW-B

Battery Well

Multicharger Battery Well

Single-bay Charger Battery Well

1. Battery Pocket

2. Battery Charging Contacts

3. Single-bay Charger Battery

Retaining Springs*

Figure 5 Battery Pockets

Battery charging and recharging cannot occur until the battery pack’s terminals are in contact with

the charging contacts in the battery pocket of a powered multi-charger or single-bay charger.

If the multicharger LED turns orange after inserting a battery instead of red, it means the battery is

in backwards.

* There are very small battery retaining mechanisms in the multi-charger battery pockets.

Rechargeable Lithium Ion Battery Pack 5

E-EQ-BRSCHGROGWW-A Bluetooth Ring Scanner Battery Charger User’s Guide

Rechargeable Lithium Ion Battery Pack

New batteries should be charged for 3 hours before first use or after battery storage of more than

three months. Battery Pack Model Number is 8650A376BTBOHBATTERY

Figure 6 Lithium Ion Battery Pack Charging Contacts

Note: Do not allow cleaning agents of any kind to contact the battery charging contacts; they

may be damaged. If necessary, clean them with a soft-bristle, dry brush or compressed

air.

Note: When not in use, lay the battery pack flat in a protected environment.

Battery Charge Contact Description

Power (+) Positive terminal

Thermistor (T) Temperature sensor

Ground (-) Negative terminal

Figure 7 Lithium Ion Battery Pack Label

6 Getting Help

Bluetooth Ring Scanner Battery Charger User’s Guide E-EQ-BRSCHGROGWW-B

To determine the age of the battery, check the LXE ship date on the battery. The ship date is

marked and shows the month and the year that the battery was shipped. The first field (labeled J,

F, M, A, etc.) is the month the battery was shipped. The second field (numbers) is the last number

of the year. So if the F and the 9 are marked, the battery was shipped in February of 2009.

To determine the actual shipping date, you may have to use the serial number on the battery to

determine the ship date. Contact your LXE representative for assistance.

• Store batteries in locations that maintain an ambient temperature of approximately 25°C

(77°F).

• Immediately replace batteries in LXE devices with the appropriate, fully charged battery

when LXE equipment battery warnings are issued/heard/displayed.

• Discard defective, shorted or end-of-life batteries.

• Any battery that is over a year old is considered an old battery.

• Replace all batteries more than a year old with new batteries.

Getting Help

LXE manuals are now available on one CD and they can also be viewed/downloaded from the

LXE website. Contact your LXE representative to obtain the LXE Manuals CD. You can also

check the LXE website for the latest releases of LXE manuals.

You can get help from LXE by calling the telephone numbers listed on the LXE Manuals CD, in

the file titled Contacting LXE. This information is available on the LXE website.

Explanations of terms and acronyms used in this manual are located in the file titled LXE

Technical Glossary on the LXE Manuals CD and on the LXE website.

Accessories

Battery, Bluetooth Module 8650A376BTBOHBATTERY

Multi-charger, 8 Bay Bluetooth Module US 8650A377BTBOHCHGRUS

Multi-charger, 8 Bay Bluetooth Module WW 8650A378BTBOHCHGRWW

Single-bay Charger, 1 Bay Bluetooth Module US 8650A379SINGLECHGRUS

Single-bay Charger, 1 Bay Bluetooth Module WW 8650A380SINGLECHGRWW

E-EQ-BRSCHGROGWW-B Bluetooth Ring Scanner Battery Charger User’s Guide

Installation and Operation

Overview

The life and capacity of a Lithium Ion battery can vary significantly depending on the discharge

current and the environment in which it is used. As with all batteries, expect to see a reduction in

the total number of operations a fully charged battery pack can deliver as it ages.

Charging times may increase but will not exceed three hours. Battery packs do not need to be fully

discharged between charge cycles.

Normal Operations

The optimal operating temperature range for the chargers is between 0°C (32°F) and 40°C

(100°F). While charging, the charger and battery pack will generate enough heat to feel warm.

This is normal and does not indicate a problem.

Do not store the battery pack in direct sunlight or anywhere the battery pack cannot cool down. If

the battery pack is hot after removal from the Bluetooth Ring Scanner, allow it to cool at room

temperature before placing it in the charger.

Charge times may increase significantly if the battery is warm or hot, since it takes the battery

pack longer to cool down while in the battery well. If the battery pack is hot from severe

environmental use and immediate recharging is necessary, place the battery pack in a cool air

stream or in a cool location until it is no longer warm to the touch before charging.

Do not place or store the Single-bay Charger or the Multi-Charger in hazardous locations.

Warning: The Bluetooth Ring Scanner Multi-bay Charger is to be used to charge

an I.T.E. Recognized Battery pack manufactured by Helix Co., Ltd.

(Model: HNP-40, LXE, P/N 161987-0001, rating 3.7V, 750mAh).

Charging any other type of battery pack in the Bluetooth Ring Scanner

Multi-bay charger is prohibited.

Warning: Use the provided AC power supply, only, with the Bluetooth Ring

Scanner Multi-bay Charger. Using any other type of AC power supply is

prohibited.

8 Overview

Bluetooth Ring Scanner Battery Charger User’s Guide E-EQ-BRSCHGROGWW-B

Using the Battery Charging Pocket

Inserting the Battery Pack

Caution!

It is important that battery packs are inserted into the charging pocket correctly,

using the direction of the arrow on the battery label as a guide. Inserting the battery

incorrectly may result in damage to the battery pack or the charger.

When preparing the battery pack for insertion into the charger well, hold the battery with its three

charging contacts in line with the three charging terminals in the battery pocket (using the

direction of the arrow on the battery label as a guide).

If necessary, stabilize the charger with your hand before inserting a battery.

Firmly press the battery straight down into the battery charging pocket.

See figure titled Battery Well.

Caution!

Do not "slam" or slide the battery pack into the charging pocket. Damage may

result.

Removing the Battery Pack

If necessary, stabilize the charger with your hand before removing a battery from a battery well.

Grasp the battery firmly and pull it straight up and out of the battery well.

Progress Monitoring 9

E-EQ-BRSCHGROGWW-A Bluetooth Ring Scanner Battery Charger User’s Guide

Progress Monitoring

The LED located below each charging pocket indicate the status of the battery in the pocket.

Charge Timers

Multi-charger

The battery pocket timers are dynamic and based upon the capacity of the battery pack. There is a

timeout period for the soft start and another timeout period for the overall time required to charge

the battery to full capacity. The pocket’s LED flashes red when the charging pocket timeout period

has expired.

Single-bay Charger

The Single-bay charger does not contain a timer. The charger provides a soft charge mode for

deeply discharged batteries, a fast charge mode and a constant-charge mode that maintains power

levels in charged batteries. Battery charge time to full capacity is three hours.

Interpreting the Single-Bay Charger LED

RED

Continuous Battery pack is charging.

GREEN

Continuous Charger is plugged in – Battery is not receiving power through the charging

pocket, or battery is not fully seated in charging pocket.

Battery pack charge complete – Battery is ready.

10 Progress Monitoring

Bluetooth Ring Scanner Battery Charger User’s Guide E-EQ-BRSCHGROGWW-B

Interpreting the Multi-charger LEDs

Figure 8 Interpreting the LEDs

RED - on any pocket

Continuous Battery pack - Charging (any charge pocket).

Flashing Battery pack fault or failure.

Battery charger timeout period expiration.

GREEN - on any pocket

Continuous Battery pack charge complete - Ready.

Amber - on any pocket

Continuous Battery pack temperature is out of range - Standby.

Battery not inserted correctly.

NO LIGHT - on a pocket

No battery pack installed.

NO LIGHT - on every pocket

No AC power available to the Charger.

Troubleshooting 11

E-EQ-BRSCHGROGWW-A Bluetooth Ring Scanner Battery Charger User’s Guide

Troubleshooting

The following is intended as an aid in determining whether the battery pack or the charger may be malfunctioning.

Problem Cause Solution

Battery pack does not fit in

battery well.

Different manufacturer's battery

pack, or there is an object in the

battery well.

Check if the battery pack is LXE part

number 8650A376BTBOHBATTERY. If

not, do not use. Remove the object from

the battery well.

No battery pack in charger, but

any of the LEDs are on.

Dirt or foreign objects are in the

battery well.

Unplug charger from outlet. Remove any

dirt or foreign objects from battery wells.

If the LEDs continue to remain ON, the

charger may be defective. Return charger

to an authorized LXE service center.

Charger is plugged into a live

outlet, battery pack is inserted,

but RED LED is OFF and no

other LEDs are on, or all LEDs

are off.

• All battery pack contacts

are not making contact with

all charging terminals in the

battery well.

• Faulty battery pack.

• New battery pack, same

result.

• Push battery pack in firmly. Do not

"slam" the battery pack into the

battery well. Remove the battery

from the charging well, turn it

around and reinsert.

• Replace battery pack.

• Contact LXE for replacement

options.

When you first put a fully

charged battery pack in the

battery well, the RED LED

comes on, indicating the battery

pack is charging.

During the first few minutes, the

charger checks the battery pack

for correct voltage and charge

state. During this time the LED

is RED and is continuously ON.

After charging is complete, the

LED is GREEN.

There is nothing wrong with the battery

pack or charger.

Current could not be sourced

through the battery pack due to

age, exhaustion or damage to

the battery cell(s). The battery

pack does not communicate

with the charger.

Contact LXE for battery pack

replacement options.

The battery pack voltage has not

reached 4.2V within the timeout

period and the charger has timed

out.

Contact LXE for battery pack

replacement options.

LED is flashing RED at any

station.

The charger’s timeout period

has expired.

Make sure that the battery pack

temperature is within specification and

retry charging. If problem repeats,

contact LXE for battery pack replacement

options.

12 Troubleshooting

Bluetooth Ring Scanner Battery Charger User’s Guide E-EQ-BRSCHGROGWW-B

Problem Cause Solution

Solid AMBER LED when

battery pack is inserted in the

charger.

The battery pack is too hot or

too cold to charge.

Battery pack is backwards.

Remove battery pack from the charger

and allow it to adjust to room

temperature.

Note: If the battery pack is left in the

charger, it will cool down or warm to a

temperature upon which the charger will

begin the charge cycle. However,

depending on the temperature of the

battery, it may take 2-3 hours to adjust.

The cool-down of a battery pack is much

quicker if the battery is not in the battery

well.

Maintenance

Use a clean soft cloth to wipe any dirt, moisture or grease from the battery pack, contacts or the

charger. Do not use any liquid to clean the battery pack or charger contacts.

Storage

Battery packs should be kept in a cool, dry place whenever possible. Do not store battery packs in

direct sunlight, on a metal surface, or anywhere the battery pack cannot cool down. Do not leave

the battery pack in a non-operating charger. The battery pack may discharge through the charger

rather than hold its charge.

Service

There are no user serviceable parts in the Rechargeable Lithium Ion Battery Pack or the chargers.

Should your battery charger require service, contact LXE.

E-EQ-BRSCHGROGWW-B Bluetooth Ring Scanner Battery Charger User’s Guide

Technical Specifications

Operating Temperature Ranges

Multi-Charger

Minimum Maximum Comment

Operating 0°C (32°F) +45°C (113°F)

Battery packs will only be charged when their temperature

is between 0°C (32°F) and 40°C (100°F).

Charging 0°C (32°F) +45°C (113°F)

Battery packs will not begin charging if their temperature

is outside this range.

Storage -10°C (14°F) +50°C (120°F) Unit is off.

Single-bay Charger

Minimum Maximum Comment

Operating 0°C (32°F) +40°C (100°F)

Battery packs will only be charged when their temperature

is between 0°C (32°F) and 40°C (100°F).

Storage -10°C (14°F) +50°C (120°F) Unit is off.

Electrical

Parameter Min Max. Comment

Power Supply Input

Voltage (V

AC-IN

)

100 VAC 240VAC Auto-switching

Power Supply Input

Frequency (freq)

47Hz 63Hz

Note: Battery packs may leak up to 1mA current through the battery contacts when left in an unpowered

charger battery well.

14 Physical Dimensions

Bluetooth Ring Scanner Battery Charger User’s Guide E-EQ-BRSCHGROGWW-B

Physical Dimensions

Multi-Charger Single-bay Charger

Weight Battery: 0.55oz / 15.6g

Without batteries: 9.10oz / 258g

With 8 batteries: 13.85oz / 392g

AC Adapter: 6.40oz / 181g

Without battery: 2.05oz / 58g

With battery: 2.75oz / 78g

With battery and power plug: 3.25oz /

92g

Power plug: 0.70oz / 19.8g

Plug Type IEC; 2-prong IEC; 2-prong

Length 9” / 23cm 2.9” / 7.4cm

(with 2-prong plug 4” / 10cm)

Width 3.25” / 8.25cm 1.9” / 4.8cm

Height 1.25” / 3.17cm (with batteries 2.5” / 6.3cm) 1.15” / 2.92cm

(with battery 2.25” / 5.71cm)

Mounting Distance between mounting holes: 5.9” / 14.9cm Mounts to AC outlet w/2 prong plug

LXE 8650A378BTBOHCHGRWW User manual

Brand: LXE

Model: 8650A378BTBOHCHGRWW

Type: User manual

This manual is also suitable for

Download PDF

report

LXE 8650A378BTBOHCHGRWW User manual

This manual is also suitable for

LXE 8650A378BTBOHCHGRWW User manual

Related papers

Other documents