Heiman HS2WD-Z User manual



HS2WD‐Z(SmartSiren)

Z‐WaveDevice

GuideDocument





Productdescripion

‐SmartSirensupportsOTAfunctionandS2encryptionfunction.

‐Productsupportsoundandlightalarm.

‐ProductisS2Unauthenticateddevices.

‐ThisdeviceisasecurityenableZ‐WavePlusproductthatisabletouseencryptedZ‐WavePlus

messagestocommunicatetoothersecurityenableZ‐WavePlusproducts.

Note:A"SecurityEnableZ‐WaveController"mustbuusedinordertofullyutilizethisfunction.



1‐DeviceADDforInclusion



InclusionStep

Net_Button

LEDinditication



‐  Click[Add]iconinZ‐WaveController.

‐  PresstheNet_Button3timeswithin1.5s,GreenLEDisBlinking3timeswithin1.5second.

‐  IfaddProcessissuccessful,GreenLEDwillturnoff.



2‐DeviceRemoveforExclusion

‐  Click[Remove]iconinZ‐WaveController.

‐  PresstheNet_Button3timeswithin1.5second.

‐  IfremoveProcessissuccessful,GreenLEDisBlinking6times,thenturnoff.

3‐Devicenormalmode

Thedeviceispoweredon.TheredLEDisonfortwosecondstoextinguish.Thedeviceis

poweredon.Ifthedeviceisaddedtothegateway,thegatewaycancontrolthedevicealarmand

cancelthealarm.Whenthealarmmodeisused,thedeviceemitsanalarmsoundandthered

LEDflashes.

‐Backupbattery:

Themainpoweroftheequipmentiscutoff,andthebackupbatteryisusedtokeepthe

equipmentonstandbyfor4hours,andthentheequipmentcanalsobealarmedfor5minutes.

4‐DeviceFactoryReset

‐LongpressNet_Buttonatleast10secondsintheproduct.

‐DeviceResetLocallynotificationisTransmitted.

Pleaseusethisprocedureonlywhenthenetworkprimarycontrollerismissingorotherwise

inoperable.



5‐Association&AssociationGroupInformation

‐LifelinebetweencontrollerandHS2WD‐Z

‐Supportedcommandclasses

DeviceResetLocally,BatteryandSwitchBinaryreport.

‐Maximumsupportednodeis5

‐AssociationGroupdescription

Associationgroup1:Lifelineassociationgroup

Includecommandclasses:SwitchBinaryreport,BatteryandDeviceResetLocallynotification.

6‐BinarySwitchReport

‐Gatewaycansetdevicealarmandshutdownalarm

‐BinarySwitchReportis0xfftosetalarm

‐BinarySwitchReportissetto0x00tocancelthealarm



7‐Devicesfrommultiplemanufacturersinonenetwork

‐  ThisproductcanbeincludedandoperatedinanyZ‐Wavenetworkwith

otherZ‐Wavecertifieddevicesfromothermanufacturersand/orother

applicants.Allnon‐batteryoperatednodeswithinthenetworkwillactas

repeatersregardlessofvendortoincreasereliabilityofthenetwork.

SwitchTypeValueStatus



BinarySwitchReport

0x00OFF

0xFFON



8‐Z‐WaveSpecifications

8.1‐DeviceType:SwitchBinary

8.2‐RoleType:AOS(Alwaysonslave)

8.3‐CommandClassSupport/Control

8.3.1‐Z‐WaveplusInfoVersion2

8.3.2‐SwitchBinaryVersion1

8.3.3‐AssociationVersion2

8.3.4‐AssociationGroupInfoVersion1

8.3.5‐TransportServiceVersion2

8.3.6‐VersionVersion3

8.3.7‐ManufacturerSpecificVersion2

8.3.8‐DeviceResetLocallyVersion1

8.3.9‐PowerlevelVersion1

8.3.10‐BatteryVersion1

8.3.11‐SecurityVersion1

8.3.12‐Security2Version1

8.4.13‐SupervisionVersion1

8.3.14‐FirmwareUpdateMdVersion4

8.3.15‐MultiChannelAssociationVersion3

8.4-The below listed CommandClassareallSupportedtheSecurityS2

8.4.1‐SwitchBinaryVersion1

8.4.2‐AssociationVersion2

8.4.3‐AssociationGroupInfoVersion1

8.4.4‐VersionVersion3

8.4.5‐ManufacturerSpecificVersion2

8.4.6‐DeviceResetLocallyVersion1

8.4.7‐PowerlevelVersion1

8.4.8‐BatteryVersion1

8.4.9‐SupervisionVersion1

8.4.10‐MultiChannelAssociationVersion3

8.4.11‐FirmwareUpdateMdVersion4

9‐BatteryReportdescription

Thebatteryistransmittedinhalfanhour

‐  BatteryReportistransmittedwhenabatteryfallslessthan0%

‐

BatteryVoltageBatteryLevel

3.7V~4.1V0~100(%)

Under3.7V 0xFF



9‐BasicCommandClassdesription

‐Supportcommandclassversionis2.

‐Gatewaycansetdevicealarmandshutdownalarm



‐BasicSetis0xfftosetalarm

‐BasicSetissetto0x00tocancelthealarm



10‐TechnicalSpecifications

ModelNo.HS2WD‐Z

RFfrequency868.40‐869.85MHz

RFoperatingdistanceUpto100moutdoorlineofsight

Upto40mindoor

Temperature‐10℃~50℃

Humidity95%max

Weight156g





BasicTypeValueStatus



BasicSet

0x00OFF

0xFFON

Heiman HS2WD-Z User manual

Related papers

Other documents