Vivotek AW-IHB-0800 Installation guide

Vivotek
Brand
Vivotek
Model
AW-IHB-0800
Type
Installation guide

Vivotek AW-IHB-0800 is an industrial unmanaged switch that supports 4x GbE 90W bt PoE, 2x GbE UTP, and 2x GbE SFP ports. It’s IEEE 802.3af/at/bt compliant and delivers the real full-load output of 360W on 4 PoE ports (up to 90W per port). This industrial PoE switch also features a wide operating temperature range from -40ºC to 75ºC for harsh environment and must be grounded properly.

Vivotek AW-IHB-0800 is an industrial unmanaged switch that supports 4x GbE 90W bt PoE, 2x GbE UTP, and 2x GbE SFP ports. It’s IEEE 802.3af/at/bt compliant and delivers the real full-load output of 360W on 4 PoE ports (up to 90W per port). This industrial PoE switch also features a wide operating temperature range from -40ºC to 75ºC for harsh environment and must be grounded properly.

1. Install the converter in a ventilated and dry place that is free of electromagnetic source, vibration, moisture, and dust.
2. Make sure the ventilation openings on the converter are not blocked.
Single-mode): 9/125um ,1310nm.
AW-IHB-0800 Industrial Unmanaged 90W bt PoE Switch
Quick Installation Guide
The AW-IHB-0800 is an industrial unmanaged switch that supports 4x GbE 90W bt PoE, 2x GbE UTP, and 2x GbE SFP ports.
It’s IEEE 802.3af/at/bt compliant and delivers the real full-load output of 360W on 4 PoE ports (up to 90W per port).
This industrial PoE switch also features a wide operating temperature range from -40ºC to 75ºC for harsh environment.
IMPORTANT:
INTRODUCTION
CONNECTION
* 1x PoE switch * 1x Quick Installation Guide * 1x 4-pin terminal block
* 1x DIN rail bracket
PACKAGE CONTENTS
1. Pull out the 2-pin terminal block.
4. install the 2-pin terminal block, and check power LED.
5. The switch must be grounded properly by using a ground wire to connect switch ground screw to earth ground,
otherwise, the surge protection level will be greatly reduced.
Power LEDs
LED Color State Description
Power Amber On The switch is powered on correctly.
Off Not receiving power from power 1 or power 2.
PoE Link Amber On PD is detected on the designated port.
Off No PD is detected.
Data Link Green On Tx link is detected.
Off Link is not detected.
Flashing Data is being transmitted or received.
SFP Link Green On Fiber link is detected.
Off Fiber link is not detected.
Flashing Data is being transmitted or received.
Copyright © 2022 VIVOTEK INC. All rights reserved.
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
| +886- 2-82455282|F +886-2-82455532|E sales@vivotek.com
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298 | s[email protected]
VIVOTEK Europe
Zandsteen 15, 2132 MZ Hoofddorp Delta Electronics
T:+31 (0)20 800 3817 E:[email protected]m
::E:T:
4. DC input: 48V~56VDC for 30W 802.3at/af. DC input: 52~56VDC for 90W 802.3bt Follow the printed polarity for V+,
V-, and Ground.
GbE PoE
RJ45 ports
PoE link LED
Data link LED
GbE RJ45 ports
GbE SFP ports
Reset button
DIN rail
PW2 LED
PW1 LED
Power input 1 Power input 2
DC Input: 48~56VDC
Ground screw
* Make sure the grouning
resistance is lower than
0.5Ω.
AC-to-DC power
100~240 VAC IN
Solid or stranded (AWG): 12-24/14-22
Wire strip length: 7-8mm
Torque: 5lb-In/0.5Nm/0.56Nm
DC: 48V ~ 56V for 30W at/af
DC: 52 ~ 56VDC for 90W bt
IMPORTANT
  • Page 1 1

Vivotek AW-IHB-0800 Installation guide

Vivotek
Brand
Vivotek
Model
AW-IHB-0800
Type
Installation guide

Vivotek AW-IHB-0800 is an industrial unmanaged switch that supports 4x GbE 90W bt PoE, 2x GbE UTP, and 2x GbE SFP ports. It’s IEEE 802.3af/at/bt compliant and delivers the real full-load output of 360W on 4 PoE ports (up to 90W per port). This industrial PoE switch also features a wide operating temperature range from -40ºC to 75ºC for harsh environment and must be grounded properly.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents