AUTOTECH 10.297.212K Installation guide

Type
Installation guide

This manual is also suitable for

AUTOTECH 10.297.212K is a sport-tuned exhaust system designed to enhance the performance and sound of your 1985-92 VW A2 model. This system is crafted from high-quality materials and engineered to provide optimal airflow, resulting in increased horsepower and torque. The AUTOTECH 10.297.212K exhaust system features a free-flowing design that reduces backpressure, allowing your engine to breathe more efficiently. This translates to improved acceleration, throttle response, and overall driving experience.

AUTOTECH 10.297.212K is a sport-tuned exhaust system designed to enhance the performance and sound of your 1985-92 VW A2 model. This system is crafted from high-quality materials and engineered to provide optimal airflow, resulting in increased horsepower and torque. The AUTOTECH 10.297.212K exhaust system features a free-flowing design that reduces backpressure, allowing your engine to breathe more efficiently. This translates to improved acceleration, throttle response, and overall driving experience.

A U T O T E CH
Installation Instructions
Phone 949.240.4000 Fax 949.240.045032240-E Paseo Adelanto, San Juan Capistrano, CA 92675
PART NUMBER: 10.297.210K; 10.297.211K; 10.297.212K; 10.297.214K
DESCRIPTION: AUTOTECH SPORTTUNED EXHAUST SYSTEM FOR A2 MODELS, 1985-92
As the removal and installation of the A2 VW exhaust system is a relatively simple one,
the purpose of this sheet will be to overview the procedure on how to perform a successful
installation. Please read this entire page before proceeding.
Rear Muffler
Jetta 2 Golf 2
Clamp with hanger
welded on.
Procedure:
Note: Always use gloves and eye protection when working with exhaust system components.
1. Loosen, but do not remove the left rear wheel lug bolts. Jack up the left side of the car and
secure it with jackstands. Remove the left rear wheel.
2. Apply some penetrating oil to the clamp bolts and to the joints themselves and let sit for
10-30 minutes in order to loosen up some of the rust that may have accumulated. This will
make disassembly of your old exhaust system much easier. Loosen the clamp bolts and slide
clamps off the joints.
3. Before installing the AUTOTECH system, first lay out all the components on the ground to
familiarlize yourself with their installed orientation.
4. Remove the old exhaust system, starting from the rear of the car and working your way
forward.
5. Now, loosely install your new system, starting at the front. Start with the front pipe that
slips onto the catalytic convertor, and work your way back. Be sure to install all the
components loosely, so that you can rotate or adjust any pieces for proper fit and alignment.
Figure A
Figure D Shows the over-axle pipe
again, this time with the muffler
attached. The arrow is pointing
out the gap between the pipe and
the axlebeam.
Figure C shows the proper
alignment between the hook on
the chassis and on the exhaust
system (mid-muffler shown).
Figure B shows a rear view at
the over-axle pipe, the way it
should be hung, and the space
between the axle and the pipe.
  • Page 1 1
  • Page 2 2

AUTOTECH 10.297.212K Installation guide

Type
Installation guide
This manual is also suitable for

AUTOTECH 10.297.212K is a sport-tuned exhaust system designed to enhance the performance and sound of your 1985-92 VW A2 model. This system is crafted from high-quality materials and engineered to provide optimal airflow, resulting in increased horsepower and torque. The AUTOTECH 10.297.212K exhaust system features a free-flowing design that reduces backpressure, allowing your engine to breathe more efficiently. This translates to improved acceleration, throttle response, and overall driving experience.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI