AUTOTECH 10.297.222K Installation guide

Brand: AUTOTECH

Model: 10.297.222K

Type: Installation guide

This manual is also suitable for

AUTOTECH 10.297.222K is a sport-tuned aluminized exhaust system designed to enhance the performance and sound of your 1993-1998 Audi A3 4-cylinder vehicle. It features a single over-tube hanger for easy installation and a drain hole on the back plate of the muffler to prevent water accumulation. Experience improved exhaust flow, reduced weight, and a throaty exhaust note with this high-quality system.

AUTOTECH 10.297.222K is a sport-tuned aluminized exhaust system designed to enhance the performance and sound of your 1993-1998 Audi A3 4-cylinder vehicle. It features a single over-tube hanger for easy installation and a drain hole on the back plate of the muffler to prevent water accumulation. Experience improved exhaust flow, reduced weight, and a throaty exhaust note with this high-quality system.

Phone 949.240.4000 Fax 949.240.045032240-E Paseo Adelanto, San Juan Capistrano, CA 92675

AUTOTECH

Installation Instructions

Part Number: 10.297.220K; 10.297.222K

Description: SPORTTUNED ALUMINIZED EXHAUST SYSTEM, A3 4-cylinder 1993-98

Notes: This AUTOTECH exhaust for Golf and Jetta 3 vehicles is patterned after the 1996

and later factory design, using a single over-tube hanger just ahead of the

midmuffler. 1993-95 cars with a dual hanger design are converted to the later,

single hanger style using the hanger (1H0.253.144C) supplied with the Autotech

exhaust.

Procedure:

Note: Always use gloves and eye protection when working with exhaust system components.

1. Loosen, but do not remove the left rear wheel lug bolts. Jack up the left side of the car and

secure it with jackstands. Remove the left rear wheel.

2. Apply some penetrating oil to the clamp bolts and to the joints themselves and let sit for

10-30 minutes in order to loosen up some of the rust that may have accunulated. This will

make disassembly of your old exhaust system much easier. Loosen the clamp bolts and slide

clamps off the joints.

3. Before installing the AUTOTECH system, first lay out all the components on the ground to

familiarlize yourself with their installed orientation.

4. Remove the old exhaust system, starting from the rear of the car and working your way

forward.

5. Loosely install your new system. Start with the front pipe that slips onto the catalytic

convertor, and work your way back. Be sure to install all the components loosely, so that you

can rotate or adjust any pieces if necessary, for proper fit and alignment.

6. Of the 5 clamps supplied, 3 have the tubular hangers welded on. Note positions below:

144A

144B

144C

Drain Hole should be at

6 O'clock Position on

back of rear muffler.

Phone 949.240.4000 Fax 949.240.045032240-E Paseo Adelanto, San Juan Capistrano, CA 92675

Fig 1. Right side view of midpipe hanger

(a) and clamp installed. The supplied

rubber hanger (b) bolts to the car in

place of the dual hanger assembly

found on 1993-95 vehicles. Hook in fore-

ground is not used on the A3.

Fig 2. Right side view of clamp/hanger

installed at front of rear muffler.

Fig 3. Right side view of clamp/hanger

installed at back of rear muffler.

Fig 4. Rear view of rear muffler and

tailpipe assembly on a Golf 3. Note

the position of the drain hole on

the back plate of the muffler. This

shows the rotation of the rear muf-

fler for best fitment.

b

a

front >

1
2

AUTOTECH 10.297.222K Installation guide

Brand: AUTOTECH

Model: 10.297.222K

Type: Installation guide

This manual is also suitable for

AUTOTECH 10.297.222K is a sport-tuned aluminized exhaust system designed to enhance the performance and sound of your 1993-1998 Audi A3 4-cylinder vehicle. It features a single over-tube hanger for easy installation and a drain hole on the back plate of the muffler to prevent water accumulation. Experience improved exhaust flow, reduced weight, and a throaty exhaust note with this high-quality system.

Download PDF

Related papers

Other documents