CTA PAD-SCGS User manual

Brand: CTA

Model: PAD-SCGS

Type: User manual

CTA PAD-SCGS is a versatile floor stand designed to securely hold and display your tablet device. It features a gooseneck holder that allows for flexible positioning and a sturdy base with swivel casters for easy mobility. The adjustable height and rotating grip enable you to customize the stand according to your needs. The battery case attachment provides power to your tablet, ensuring uninterrupted use while on display.

Compact Security Gooseneck Floor Stand

PAD-SCGS

INSTRUCTION - MANUAL

888-733-4448

CONTENTS:

1. Attaching Foam Pad to Tablet Holder

Select the appropriate foam pad (N) according to the

thickness of your tablet (or tablet in its case), then

press adhesive side into center of tablet holder.

2. Installing the Swivel Casters

INSTRUCTIONS:

2a. Place a

spring washer (I)

over the screw

bolt on each

caster (E).

2b. Place the

screw bolt from

each wheel (E)

through the

metal base (C),

then place a nut

cover (H) over

the top of each.

Screw down

clockwise by

hand, then use

wrench (G) to

tighten further.

Wheel

Screw Nut Cover

Spring

Washer

Metal

Base

Use this table to determine the

appropriate foam pad to use

with your tablet.

Note: sizes refer to total tablet

size with or without a case.

Foam Pad

Thickness

Tablet

Thickness:

1mm 0.67-1.06in

5mm 0.51-0.91in

10mm 0.31-0.71in

17-27mm

13-23mm

8-18mm

1mm Foam Pad

5mm

Foam Pad 10mm

Foam Pad

Bx1

x4 x4

G N

888-733-4448

Metal connection

Height

Adjustment

Knob

Pole (B)

Metal

Cross Base (C) x2

Connection Screw Bolt (K),

Washers (L) and Nut (M)

Pole Assembly and Pole Nut

Cross Base Sections (2)

Allen Key (J)

3a. Place the metal base of the base pole (B)

with the higher piece on top of the cross

base (C). Align the holes at the bottom of the

pole (B) with the holes on the cross base (C).

3b. Insert a screw bolt (K) with a

washer (L) into each of 4 holes.

Place another washer (L) on the

underside of each screw bolt. Grip

the nut (M) on the underside with

one hand, and use the other tighten

each screw with the allen key tool

(J). Repeat for all four screw bolts.

3. Base Assembly and Connecting the Metal Cover

3c. Rotate the grip counter

clockwise to loosen

completely and remove from

the top of the pole.

3e. Place the grip back over

the stand pole (B) and rotate

clockwise until securely

tightened.

3d. Place the square metal

cover (D) over the top of the

pole (B) and slide down to

the stand base.

4. Connecting Gooseneck

Holder & Battery Case

5. Installing Tablet Device

Adjusting the Floor Stand

4a. Place battery

case (F) over top of

metal connection.

Note: if the Y screw

is already in,

unscrew before

attaching the

gooseneck.

4b. Screw the

gooseneck onto the

metal connection of

the pole by turning

clockwise. Be sure

that the battery case

is on the opposite

side of the pole as

the Y screw.

5a. Insert key (O) and set

position to unlock. Remove key,

then slide holder (A) open.

Tighten and loosen

the holder connection

screw to adjust ease

of rotation.

Adjust the gooseneck

to desired position.

Rotate plastic grip to

loosen, then adjust

pole to desired height.

Rotate back to tighten.

5b. Load tablet corner first into

one end. Insert key and set to

lock, the slide holder shut until

secured. Remove key.

4c. Turn the Y screw

clockwise to tighten

the connection.

Y Screw

CTA PAD-SCGS User manual

CTA PAD-SCGS User manual

Related papers

Other documents