CTA PAD-SHFSWAO User manual

Brand: CTA

Model: PAD-SHFSWAO

Type: User manual

PAD-SHFSWAO

INSTRUCTION - MANUAL

Contents :

2. Assembling the base to body : 3. Locking casters :

1. Installing the wheels :

INSTRUCTIONS :

4. Setting up tablet in holder :

5. Assembling base stand with gooseneck,

holder and battery cradle : 6. Setting up handle :

7. Setting up basket :

Y-Screw

How to flex and adjust product :

Lock security Adjusting Gooseneck Asjusting height

888-733-4448

for 7-13-Inch Tablets

888-733-4448

Heavy-Duty Medical Mobile Floor

Stand and Accessories (White)

x1 x1

Foam

Bundle

Battery

Cradle

Wrench

Tool

Washer

x1 x1

1A. Take one wheel (E) and align it to the leg arm holes on the underneath of the base (H). Initially you can use your hands and manually rotate the wheel until slightly tightened.

Then use the provided wrench tool (B) at the hex nut and rotate to securely tighten the rest of the way.

3A. Press the wheel lever up or down to place wheels

in locked or unlocked mode depending if you want to be

in a mobile or stationary setup. Make sure you adjust all

(5) wheels at the same time or it won’t properly be

setup.

2A. Align the bottom of pole body (B) to the top center of the base (C). While pieces are connected, securely flip

over so you can see the bottom. Align washer (E) to the hole on the bottom. Using your hands, identify L-shaped

component (F) and rotate through the washer into the hole until securely tightened. Pole body and base should

now be securely attached to each other.

5A. Take the gooseneck with holder (A), the battery cradle (J), the base

stand (B), and align them all together as shown in the right. First, hook

the battery cradle onto the base stand metal adapter. Then rotate in the

gooseneck component (A) into the base stand (B) until securely

tightened. Turn the Y screw (see detail diagram to the right) to securely

fasten the gooseneck to the base stand.

6A. Find the desired height on the

pole / floorstand (B) where you

wish to attach the handle (K).

Then align the screw and the U

bracket (L,M) with the opening in

the handle (K).

7A. Find the desired height on the pole / floorstand (B) Align U

bracket (O) holes with basket (N) screw holes on either side of the

central pole. Pass screw (R) through washer (Q), then through

screw hole, and turn in nut (P) on opposite side.

6B. Rotate in screw clock

wise as shown until securely

tightened.

Identify the center pole height adjustment knob. Rotate

clockwise and counterclockwise to raise or lower the

center pole for preferred height. Once desired height

is set, rotate knob in the middle opposite side of the

handle to tighten and create a more rigid and secure

setup.

Using your hands, simply adjust for

a multitude of angles the

gooseneck until desired orientation,

tilt angle, side angles are all

achieve for the preferred setup.

Using an allen key (S), tighten the

joint to create a more static and

rigid setup. Loosen to allow

adjustability as needed.

1.Isert the key into the lock slot.

2.Press and hold on the release button

to unlock the holder.

Tightening &

loosening main joint

1 5 10 15

mm mm mm mm

(1) Press and hold

on the button

4A. Press and hold on the button as shown, open the arms

of the holder at the desired measure of tablet.

4C. Close arms to adjust frame to secure

your tablet as shown.

4B. Insert Foam pad (I) that fits better into the center of holder,

then insert Tablet in place as shown.

360º rotation

270º

rotation

CTA PAD-SHFSWAO User manual

CTA PAD-SHFSWAO User manual

CTA PAD-SHFSWAO User manual

Related papers

Other documents