2. Genexis
  3. P6426 Fiber Twist Series

Genexis P6426 Fiber Twist Series Installation guide

  • Hello! I've reviewed the installation guide for the genexis FiberTwist Series P6426 and G6426 devices. This document provides detailed instructions for installing the device, connecting to various services, and understanding the LED indicators and buttons. It seems the device supports Wi-Fi EasyMesh, multiple ports for connectivity, and has a web interface for settings. I'm here to answer your questions about the device, so feel free to ask.
  • How to remove the dust cap?
    How can I switch the WiFi ON/OFF?
    What do solid green LEDs means?
    What to do if Status LED is solid red?
P
G
FiberTwist Series
Installation Guide
Wi-Fi EasyMeshTM suppoted
FiberTwist PG is installed on an FTUBracket
Box contents
Check if the following items are in
the gitbox:
• Genexis FiberTwist PG
• Power adapter
• Labels (self-adhesive)
Label position
The product label is positioned on the botom
of the active device. The relevant device
information is also listed on the additional
labels included in the gitbox.
Preparation
Ensure there is a power socket
within reach of where the device
is being installed.
Impotant: Instructions need to be
followed precisely and uninterrupted.
This minimizes the risk of damage (a
severe degradation of signal qualiy)
to the iber optic connectors.
Warning: Do not cover the device with
anything, this will intefere with the
ventilation of the FiberTwist.
Operation Temperature °C ~ °C
Various translations of this document (if available) and additional product information can be
foundon htps:genexis.euproductibewistdownloads
Installation guide
Remove Blind Cover or active device (if present)
. Press and hold the unlock buton (on the right side of the Blind Cover or active device).
. Rotate the Blind Cover or active device counterclockwise till it blocks.
. Remove the Blind Cover or active device from the baseplate (FTU) by pulling
it towards yourself.
. Store the Blind Cover or active device in a safe place.
Remove dust cap
. Take the FiberTwist PG out of the box.
. The dust cap is connected to the red string
located on the rear of the FiberTwist PG.
. Remove the dust cap by pulling the red string.
. Store the dust cap in a safe place.
Twist!
. Place the FiberTwist PG on the FTUBracket as shown in the picture below.
. Rotate clockwise until it clicks into place.
. Make sure the FiberTwist PG is aligned squarely on the FTUBracket.
Your FiberTwist PG is now installed!
Using the web inteface
You can access the FiberTwist P
G web inteface via a wired
connection or wireless connection.
• Wired connection: Connect an RJ
nework cable beween your personal
device and the FiberTwist PG
LAN pot (yellow connector).
• Wireless connection: Connect your
personal device to the wireless nework as
described in this installation guide.
. Use a web browser on your personal
device and navigate to the GUI URL
as printed on the labels of the
FiberTwist PG.
. Login using the credentials as
printed on the labels of the
FiberTwist PG.
Power saving options
Power saving options are available via the
web inteface.
The FiberTwist PG
is a Class  laser product.
Seting up the FiberTwist PG
. If required, connect your telephone to a
telephone pot via an RJ phone cable.
. If required, connect your personal devices
to the LAN pots via an RJ nework cable.
. If required, connect your television  set-
top box to the TV pot with a coax cable.
. Connect the supplied power adapter to
the FiberTwist PG and plug the
adapter into a power socket.
. Toggle the ONOFF buton on the botom
of the FiberTwist PG in the ON
position to turn on the device.
. If the device is connected properly and
the sevice is active on the iber pot, the
Status, Uplink and Internet LEDs will have
a solid green color.
Switching the WiFi ONOFF
The WiFi function of the FiberTwist P
G can be switched ON or OFF by
means of the Mode buton.
• Switch OFF: On the FiberTwist P
G, press and hold the Mode buton
until the WiFi LED turns o.
• Switch ON: On the FiberTwist P
G, press and hold the Mode buton
until the WiFi LED turns on.
Connecting to the wireless nework
You can connect your personal device to the
FiberTwist PG via manual pairing.
If Automated pairing (WPS) is prefered, please
check for your speciic device how this can be
initiated. Before pairing , make sure
the WiFi LED is on (solid green). If not,
switch the WiFi ON as described in this
installation guide.
Manual pairing
The WiFi nework name and WiFi key
are printed on the labels of the
FiberTwist PG.
. Peform a search of available wireless
neworks on your personal device or scan
the QR-code on the label of the
FiberTwist PG.
. Select the WiFi nework name printed on
the labels of the FiberTwist PG.
. Enter the WiFi key printed on the labels of
the FiberTwist PG.
LED oveview Uplink
Green – optical WAN link is established
Green (blinking) – optical WAN link is in progress
Red (blinking) – insuicient optical input signal
O – no optical WAN link detected
Internet (IP connectiviy)
Green – connected (DNS available)
Green (blinking) – connection failed (no DNS available)
O – no IP connectiviy
Wireless (WiFi)
Green – wireless nework . GHz andor  GHz active
O – wireless neworks inactive
Phone
Green – telephony sevice registered and operational
Green (blinking) – telephony sevice in progress to register
O – telephony sevice is disabled
TV
Green – TV sevice registered and ok
Red (blinking) – insuicient optical input signal
O – no TV sevice present or registered
Status
Green – system is operational ready
Yellow – system boot initialization
Yellow (blinking) – system is not ready yet
Blue – WPS pairing successful
Blue (blinking) – WPS pairing in progress
Red – system  booting failure
O – power o
Buton oveview
Mode buton
Pairing (WPS) – press and release once
WiFi ON – press and hold until WiFi LED turns solid green
WiFi OFF – press and hold until WiFi LED turns o
Unlock buton
Remove FiberTwist PG – press
and hold while wisting counterclockwise
Reset
buton
LAN pots
Telephone
pots
ONOFF
switch
Power pot
Pot oveview
ONOFF switch
Switch ON – lip the switch to ON
Switch OFF – lip the switch to OFF
Reset buton (recessed)
Reboot – shot press once
Factoy reset – long press and hold until
all LED’s stat fast blinking green
TV pot
USB .
pot
LED dim buton
Dim LEDs – press and release repeatedly
to dim LEDs
Unlock buton
Troubleshooting
Is the Status LED solid red?
Contact your sevice provider.
Is the Status LED not solid blue ater
automated pairing (WPS)?
Automated pairing beween the FiberTwist
PG and personal device failed.
Please follow the instructions again to
connect your personal devices to the
FiberTwist PG via the
wireless nework.
Is the Status LED blinking yellow and the
Uplink LED is blinking green?
The FiberTwist PG is being
upgraded with new soware. Please wait until
the Status LED turns solid green again.
Is the Uplink LED o?
If the Uplink indicator LED is o, despite proper
connection, contact your sevice provider.
Is the Uplink LED blinking red?
Contact your sevice provider.
Is the Internet LED blinking green for
 minutes?
FiberTwist PG does not have a
connection with the broadband nework.
Please contact your sevice provider.
Is the WiFi LED o?
On the FiberTwist PG, press and
hold the Mode buton until the WiFi LED
stats blinking green or turns solid green.
Return the FiberTwist PG to
factoy default setings
With the reset buton you can reset the
FiberTwist PG to its factoy
default setings. You can press this buton
with a small pin or paperclip.
. Press and hold the reset buton until all
LED’s stat fast blinking green.
. Wait until the Status LED turns solid
green again.
Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat a
 AC Eindhoven
The Netherlands
Name and title of authorized person
Maaten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven --
The Netherlands
Hereby, Genexis Netherlands B.V. declares that the radio equipment ype FiberTwist PG
is in compliance with Directive EU, Directive EC, Directive EU and
Delegated Directive .
The full text of the EU declaration of conformiy is available at the following internet addresses:
htps:genexis.euproductibewistredibewist-p,
htps:genexis.euproductibewistredibewist-g
Frequency bands and maximum radio frequency power transmited
The FiberTwist PG operates in the frequency bands of . GHz and GHz.
The maximum radio frequency power transmited in these bands is:
•  dBm( mW) (EIRP)for the  MHz – . MHz band
•  dBm ( mW) (EIRP)for the  MHz –  MHz band *
•  dBm ( mW) (EIRP) for the  MHz –  MHz band
* In EU,  –  MHz is restricted to indoor.
EU Declaration of Conformiy
Revision . - April  - Copyright ©  Genexis Netherlands B.V. All rights reseved.
Genexis assumes no responsibiliy for any inaccuracies in this document. Genexis reseves the right
to change, modify, transfer, or othewise revise this publication without notice.
/