Genexis P2410 Installation guide

P2410
Genexis
Brand
Genexis
Model
P2410
Type
Installation guide

Genexis P2410 is a fiber optic device that provides high-speed internet connectivity. It features two LAN ports for connecting personal devices and a power port for connecting the supplied power adapter. The device has a sleek and compact design with a user-friendly interface that includes a power button, reset button, and LED indicators for system status and uplink connectivity. Genexis P2410 is easy to install and can be used in various applications, including home networking, office connectivity, and surveillance systems.

Genexis P2410 is a fiber optic device that provides high-speed internet connectivity. It features two LAN ports for connecting personal devices and a power port for connecting the supplied power adapter. The device has a sleek and compact design with a user-friendly interface that includes a power button, reset button, and LED indicators for system status and uplink connectivity. Genexis P2410 is easy to install and can be used in various applications, including home networking, office connectivity, and surveillance systems.

P
P
FiberTwist–Series
Installation Guide
Buton oveview Pot oveview
Power potLAN pots
Unlock buton
Remove FiberTwist or Blind Cover – press and
hold while wisting counterclockwise
Reset buton (recessed)
Reset – press and release
LED dim buton
Dim LEDs – press and release to dim LEDs in
steps
System
Green – system ok
Green (blinking) – booting
Red – system error
Red (blinking) – insuicient optical signal
O – power o
Uplink
Green – link ok
Green (blinking) – link ok, no remote management
O – no link
LED oveview
Box contents
• Genexis FiberTwist (active device)
• Power adapter
• Label (self-adhesive)
• Installation Guide (this document)
Label position
The product label is positioned on the
back of the active device.
Preparation
Ensure there is a power socket
within reach of where the device
is being installed.
Impotant: Instructions need
to be followed precisely and
uninterrupted. This minimizes
the risk of damage to the iber
optic connectors, causing a severe
degradation of signal qualiy.
Dierent language versions of this document and additional product information
are availableon htps:genexis.euproductibewistdownloads
Installation guide
Remove Blind Cover (if present)
. Press and hold the unlock buton (see buton oveview).
. Rotate the Blind Cover counterclockwise till it blocks.
. Remove the Blind Cover from the baseplate (FTU) by pulling
it towards yourself.
. Store the Blind Cover in a safe place.
Remove dust cap
. Take the FiberTwist out of the box.
. The dust cap is connected to the red string
located on the rear of the FiberTwist.
. Remove the dust cap by pulling the red string.
. Store the dust cap in a safe place.
Twist!
. Place the FiberTwist on the FTU as shown in the picture below,
in a –degree angle.
. Rotate clockwise until it clicks into place.
. Make sure the FiberTwist is aligned squarely on the FTU,
each edge must line up directly with the FTU below.
Your FiberTwist is now installed!
Company Name
Genexis B.V.
Company Address
Lodewijkstraat a
 AC Eindhoven
The Netherlands
Name and title of authorized person
Maaten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven --
The Netherlands
Hereby, Genexis B.V. declares that the products FiberTwist-P and
FiberTwist-P are in compliance with Directives EU, EU,
EU, Delegated Directive  and Ecodesign Directive EC.
The full texts of the EU declaration of conformiy are available at the following
internet addresses respectively: htps:genexis.euredt-P,
htps:genexis.euredt-P
EU Declaration of Conformiy
Connecting the FiberTwist
. If required, connect your personal devices to the LAN pots via an RJ
nework cable.
. Connect the supplied power adapter to the FiberTwist and plug the adapter
into a power socket.
Warning: The FiberTwist is a Class  laser product.
If at some point in the future it becomes necessay to uninstall the FiberTwist,
please place the Blind Cover back on the FTU immediately and put the dust cap
back on the FiberTwist.
Revision . - June  - Copyright ©  Genexis Netherlands B.V. All rights reseved.
Genexis assumes no responsibiliy for any inaccuracies in this document. Genexis reseves
the right to change, modify, transfer, or othewise revise this publication without notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Genexis P2410 Installation guide

P2410
Genexis
Brand
Genexis
Model
P2410
Type
Installation guide

Genexis P2410 is a fiber optic device that provides high-speed internet connectivity. It features two LAN ports for connecting personal devices and a power port for connecting the supplied power adapter. The device has a sleek and compact design with a user-friendly interface that includes a power button, reset button, and LED indicators for system status and uplink connectivity. Genexis P2410 is easy to install and can be used in various applications, including home networking, office connectivity, and surveillance systems.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents