Wacker Neuson DPP33 User manual

Brand: Wacker Neuson

Model: DPP33

Type: User manual

Wacker Neuson DPP33 is a pump pack, an accessory for a hydronic surface heater, which consists of a dedicated pump for each extra hose loop, quick-connect brass fittings, and a leader hose. This accessory is intended to be used with a surface heater in order to thaw frozen ground, cure concrete, or prevent frost and freezing. DPP33 has been designed and built strictly for the intended use described above, and using the machine for any other purpose could permanently damage the machine or seriously injure the operator or other persons in the area.

5200000069 01 0111

5200000069

Operator’s Manual

Pump Pack

DPP 33

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

DPP 33 Foreword

wc_tx001712gb.fm 3

Foreword

Machines

covered by

this manual

This manual covers machines with the following item numbers:

Machine

documentation

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing any of these documents, please contact Wacker Neuson

Corporation to order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson Corporation expressly reserves the right to make technical

modifications, even without notice, which improve the performance or safety

standards of its machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson Corporation reserves the right

to change any portion of this information without notice.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Machine Item Number Revision

DPP 33 0620429 200 and above

Foreword DPP 33

4 wc_tx001712gb.fm

William Lahner Paul Krause

Vice President of Engineering Manager, Product Engineering

WACKER NEUSON CORPORATION

2010_DPP33_DOI_en.fm

DECLARATION OF INCORPORATION

WACKER NEUSON CORPORATION, N92W15000 ANTHONY AVENUE, MENOMONEE FALLS, WISCONSIN USA

AUTHORIZED PERSON FOR TECHNICAL DOCUMENTS Axel Häret

WACKER NEUSON SE

Preußenstraße 41

80809 München

1. Category:

Pump pack

2. Model:

DPP 33

3. Item number of equipment:

0620429

Declaration of incorporation:

We hereby declare that this product is designed for installation in a machine and that commissioning is only

permitted once it has been determined that this machine corresponds to the terms of the following EC guidelines:

2006/42/EC.

5. Guidelines and standards:

This is to certify that this product meets and complies with the relevant regulations and requirements of the following

guidelines and standards: 2006/42/EC, 2006/95/EC.

The original language of this EC Declaration of Incorporation is American English.

25.3.10

Date

Declaration of Incorporation

wc_bo5200000069_01TOC.fm 7

Table of Contents

DPP 33

Foreword 3

Declaration of Incorporation 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Service Safety .................................................................................... 13

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 17

3 Lifting and Transporting 19

4 Operation 20

4.1 Control / Component Locations .......................................................... 20

4.2 Preparing the Machine for First Use ................................................... 21

4.3 Positioning the Machine ..................................................................... 22

4.4 Connecting the DPP to the Parent Surface Heater ............................ 23

4.5 Turning the Dual Pump Pack (DPP) ON and OFF ............................. 24

4.6 Emergency Shutdown Procedure ....................................................... 25

4.7 Quick-Connect Coupling Usage and Care ......................................... 26

5 Maintenance 27

5.1 Periodic Maintenance Schedule ......................................................... 27

5.2 Inspecting Electrical Cords ................................................................. 27

5.3 Cleaning the HTF Strainer .................................................................. 28

6 Troubleshooting 30

7 Technical Data 31

7.1 Machine .............................................................................................. 31

7.2 Dimensions ......................................................................................... 31

8 wc_bo5200000069_01TOC.fm

Table of Contents

DPP 33

DPP 33 Safety Information

wc_si000564gb.fm 4

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

Safety Information DPP 33

5 wc_si000564gb.fm

1.2 Machine Description and Intended Use

This pump pack is an accessory for a hydronic surface heater. The Wacker Neuson

Pump Pack consists of a dedicated pump for each extra hose loop, quick-connect

brass fittings, and a leader hose.

This accessory is intended to be used with a surface heater in order to thaw frozen

ground, cure concrete, or prevent frost and freezing.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Using the machine to heat anything other than what is stated above.

 Using the machine to pump anything other than the factory recommended heat

transfer fluid.

 Using the machine as a ladder, support, or work surface.

 Using the accessory with a Pureheat Hydronic Surface Heater.

 Not using the auxiliary control panel or on-board duplex receptacle to power the

accessory.

 Operating the machine outside of factory specifications.

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator's Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Electric shock and arc flash.

 Personal injury from improper lifting

 Tripping hazards from the hoses

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

DPP 33 Safety Information

wc_si000564gb.fm 6

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson Corporation for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not modify or defeat the safety devices.

 Only use accessories or attachments that are approved by Wacker Neuson

Corporation.

Safety Information DPP 33

7 wc_si000564gb.fm

Safe

operating

practices

When operating this machine:

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

 Do not operate a machine in need of repair.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

DPP 33 Safety Information

wc_si000564gb.fm 8

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson Corporation for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operation. Do not

operate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

 Reinstall the safety devices and guards after repair and maintenance

procedures are complete.

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson

Corporation.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker

Neuson Corporation.

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance as the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Safety Information DPP 33

9 wc_si000564gb.fm

Lifting and

transporting

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks, and other types of lifting devices

are attached securely and have enough weight-bearing capacity to lift or hold

the machine safely. See chapter Technical Data.

 Remain aware of the location of other people when lifting the machine.

 Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine. See chapter Technical Data.

To reduce the possibility of injury:

 Do not stand under the machine while it is being lifted or moved.

 Do not get onto the machine while it is being lifted or moved.

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

DPP 33 Safety Information

wc_si000564gb.fm 10

Notes

Labels DPP 33

15 wc_si000565gb.fm

2 Labels

2.1 Label Locations

wc_gr008152

DPP 33 Labels

wc_si000565gb.fm 16

2.2 Label Meanings

58 Two people are required for lifting this

machine.

60 Read the Operator’s Manual.

63 Center of gravity.

68 Do not connect machine’s power cord to a

building’s power supply or any other external

power source.

Only connect the machine’s power cord to

the accessory power receptacle on the

Ground Heater™ Hydronic Surface heater.

75 Weight/mass label.

This label indicates the total weight of the

machine.

76 Machine rating label: This label indicates

rating information for the machine.

LBS

200

173608

Labels DPP 33

17 wc_si000565gb.fm

77 CAUTION!

Hot surface hazard!

78 Warning

Pressurized contents. Turn off the machine

before disconnecting the quick-connect

couplings.

79 NOTICE!

Lift point.

Attach lifting device in this location.

xx A nameplate listing the model number, item

number, revision number, and serial number

is attached to each unit. Please record the

information found on this plate so it will be

available should the nameplate become lost

or damaged. When ordering parts or

requesting service information, you will

always be asked to specify the model

number, item number, revision number, and

serial number of the unit.

182943

181148

DPP 33 Lifting and Transporting

wc_tx001713gb.fm 18

3 Lifting and Transporting

Precautions

 Refer to chapter Technical Data for the machine’s weight.

 Do not attempt to manually lift the machine by yourself.

Lifting

To lift the machine:

1. With a partner, firmly grasp the lifting handles (a) of the machine or attach a

properly-rated lifting mechanism to the lifting bracket (b) on the top of the

machine.

2. Lift upwards, taking special care to observe safe lifting techniques.

Transporting

Before transporting the machine:

1. Disconnect the hoses.

2. Disconnect the electric power cord.

wc_gr008153

Operation DPP 33

19 wc_tx001714gb.fm

4 Operation

4.1 Control / Component Locations

wc_gr008154

4 9 8 4

Ref. Description Ref. Description

1 Enclosure 6 HTF discharge quick-connect

2 Manual lift handle 7 HTF pump 1

3 Crane lift point 8 HTF filter

4 Heat Transfer Fluid (HTF) supply

quick-connect

9 Control panel

5 Pressure gauge 10 HTF pump 2

Page is loading ...

Wacker Neuson DPP33 User manual

Wacker Neuson DPP33 User manual

Wacker Neuson DPP33 User manual

Related papers

Other documents