Road Armor 518LFF0Z Installation guide

Brand
Road Armor
Model
518LFF0Z
Category
Car kits
Type
Installation guide

This manual is also suitable for

INSTALL INSTRUCTIONS
Applicaon : 2018+ Jeep Wrangler JL
JL Rear INNER FENDER LINERS: 518LFR0Z
2018+ JEEP JL REAR FENDER LINERS Page ( 2 of 8 )
www.ROADARMOR.com
INSTALL INSTRUCTIONS
SAFETY FIRST!
• FOLLOW ALL INSTRUCTIONS, YOUR SAFETY AND THE SAFETY OF OTHERS IS MOST IMPORTANT.
• WEAR APPROPRIATE EYE PROTECTION AND EXERCISE CAUTION WHEN DRILLING / CUTTING
REQUIRED TOOLS
INCLUDED HARDWARE
I WARNING
Read the instrucons completely before beginning installaon. Before ghtening bolts,
drilling or cung where required, check to make sure there are no obstrucons such as
brake, fuel or electrical lines which may be damaged. Also keep in mind this is an aer-
market product and MAY require minor shimming and/or trimming, reaming, etc. for
proper t. Road Armor is not responsible for any damages to vehicle.
IMPORTANT NOTICE
• Be sure to inspect and test t your product to ensure proper tment before having it coated, painted, bed
lined, etc.
• Road Armor will not be responsible for the cost of coang your unit if any problems with t or nish are not
noted and addressed beforehand.
Metric and SAE Socket Sets and Wrenches Drill & Unibit
(8) 10-24 x 1/2 Bolts
(8) 10-24 Nuts
(40) 5/16”x3/4” Bolts
(32) 5/16” Flange Nuts
(8) 5/16” U-Nuts
(2) Logo Plates
(4) Nut Cover Plates
(1) PSG Boom FENDER LINER
(1) PSG Top FENDER LINER
(1) DVR Boom FENDER LINER
(1) DVR Top FENDER LINER
2018+ JEEP JL REAR FENDER LINERS Page ( 3 of 8 )
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Remove 8 plasc clips from each inner wheel well.
NOTE **If you are installing Road Armor Fender Flares skip STEP 2**
2 MARK, CUT and REMOVE plasc OEM LINER as shown below. (KEEPING STOCK FENDERS)
3 Remove rear fender assembly by rmly pulling on one end of fender unl all 12 clips “pop o”.
2
1
2018+ JEEP JL REAR FENDER LINERS Page ( 4 of 8 )
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Cut out each kit DRIVER AND PSG SIDE TEMPLATES (4 pcs) found at the end of instrucons. Cut out
hole without “crosshairs”. Align TEMPLATES with exisng fender holes and fender well edge.
2 Aer TEMPLATES are secured with tape, center punch and drill 3 holes to 3/8” (RED ARROWS)
3 Drill 5 exisng holes to 3/8” as shown with BLUE ARROWS.
FRONT DVR SIDE REAR DVR SIDE
TOP
TOP
2
3
2018+ JEEP JL REAR FENDER LINERS Page ( 5 of 8 )
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 REMOVE PROTECTIVE FILM.
2 Assemble REAR FENDER LINER using 9 - 5/16” BOLTS
& FLANGE NUTS as shown below.
3 Assemble LOGO PLATE using 4 - #10-24 BOLTS &
FLANGE NUTS as shown below.
1 2
5
3
4 Assemble REAR FENDER LINER using
4 - 5/16” U-NUTS as shown
5 Placement of both FLANGE NUT
COVERS shown with BLUE indicators.
4
2018+ JEEP JL REAR FENDER LINERS Page ( 6 of 8 )
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Install JL FENDER LINER behind Jeep fender well and secure using 11 - 5/16” HARDWARE.
1
2 Install two NUT COVER PLATES shown in locaon above. (Between inner seam and 5/16” nuts.)
3 Install ROAD ARMOR FENDER FLARE at this me or OEM rear fender are.
FINISHED!
3
2
2018+ JEEP JL REAR FENDER LINERS Page ( 7 of 8 )
www.ROADARMOR.com
INSTALL INSTRUCTIONS
TOP
TOP
2018+ JEEP JL REAR FENDER LINERS Page ( 8 of 8 )
www.ROADARMOR.com
INSTALL INSTRUCTIONS
TOP
TOP
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Road Armor 518LFF0Z Installation guide

Brand
Road Armor
Model
518LFF0Z
Category
Car kits
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents