urban ambiance UQL2133 Installation guide

Brand
urban ambiance
Model
UQL2133
Type
Installation guide

urban ambiance UQL2133 is a ceiling light fixture that provides ample illumination for your space. With its three A19 Medium Base sockets, it can accommodate up to 100W bulbs each, or three 23W CFL bulbs as an alternate option. The fixture's elegant design is complemented by its sturdy construction, ensuring durability and longevity. Installation is straightforward and can be completed in approximately 30-45 minutes. The fixture comes with all the necessary mounting hardware, including outlet box screws, mounting balls, and a hex nut and lock washer.

urban ambiance UQL2133 is a ceiling light fixture that provides ample illumination for your space. With its three A19 Medium Base sockets, it can accommodate up to 100W bulbs each, or three 23W CFL bulbs as an alternate option. The fixture's elegant design is complemented by its sturdy construction, ensuring durability and longevity. Installation is straightforward and can be completed in approximately 30-45 minutes. The fixture comes with all the necessary mounting hardware, including outlet box screws, mounting balls, and a hex nut and lock washer.

1of2
ACrossbar Assembly
x1
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar
Assembly (A). Attach the Crossbar
Assembly (A) to the Outlet Box with the
head of the Green Ground Screw facing
you. Secure it with Outlet Box Screws (not
included). Tighten until snug.
STEP 2 Fit Ceiling Canopy to
Crossbar Assembly
-
A.
eiling canopy of the Socket
Assembly to the
ceiling
Remove mounting balls from the
Crossbar Assembly (A). Fit the
c
(B) Crossbar
Assembly (A) and secure with
mounting balls. Note: The
should be snug against the
and the mounting balls. If
Not, adjust the length of the nipple
on the Crossbar Assembly (A) by
unscrewing the preassembled hex
nut and lock washer and then
screwing the mounting screws in
ceiling
canopy of the Socket Assembly
(B)
or out of the crossbar until the correct length is achieved. Once the
is secure, remove the
mounting ball and Socket Assembly (B) and proceed to Step 3.
ceiling canopy of the Socket Assembly (B)
Package Contents
Mounting Screw
Hex Nut and
Lock Washer
BA
Mounting Ball
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (3)A19 Medium Base 100W Maximum.Alternate Bulbs (3) 23W CFL.
Estimated Assembly Time: 30-45 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
B
Socket
Assembly
x1
CSide Arm
x3
DShade
x1
ECage
x1
Figure 1
Figure 2
A
Figure 3
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the ceiling
canopy of the Socket Assembly
(B) over the outlet box. Align the
holes in the ceiling canopy of the
Socket Assembly (B) with the
mounting screws, then attach the
ceiling canopy using the
previously removed mounting
balls. Hand tighten until snug.
Mounting
Screw
BA
Mounting
Ball
Figure 4
STEP 5 Assemble Shade, Cage and Bulbs-
A. Place the Shade (D) inside of the Cage (E).
B. Attach one ends of Side Arms (C) to Hooks on the side of the Socket
D
E
C
B
Hook
Hook
Bulb
Socket
Assembly (B). Lift the Cage with
Shade upward and attach another
ends of Side Arms (C) to Hooks
on the top edge of the Cage (E).
Carefully release your hands
after all Side Arms (C) are hung
properly.
C. This fixture uses standard bulb
with standard screw base.
Maximum 100 watts. Insert bulb
and screw snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
Figure 5
Installation Instructions: UQL2133
www.urbanambiance.com
2of2
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
NO. PART NUMBER REPLACEMENT PART DESCRIPTION
1
1
UQL2133SH SHADE
(3) 100W
Bulbs
(Not Supplied)
Medium
Base
SKU: UQL2133
REQ.
16” Dia.
14” Dia.
5.75”
14.25”
6” Dia.
1
www.urbanambiance.com
  • Page 1 1
  • Page 2 2

urban ambiance UQL2133 Installation guide

Brand
urban ambiance
Model
UQL2133
Type
Installation guide

urban ambiance UQL2133 is a ceiling light fixture that provides ample illumination for your space. With its three A19 Medium Base sockets, it can accommodate up to 100W bulbs each, or three 23W CFL bulbs as an alternate option. The fixture's elegant design is complemented by its sturdy construction, ensuring durability and longevity. Installation is straightforward and can be completed in approximately 30-45 minutes. The fixture comes with all the necessary mounting hardware, including outlet box screws, mounting balls, and a hex nut and lock washer.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents