Short guide for the usage of rack
holders
This publication is part of the operator's manuals of
cobas p 512 pre-analytical system (64x)
cobas p 612 pre-analytical system (63x)
Short guide for the usage of rack holders
2
Publication information
Publication version Revision date Change description
3.0 December 2019 Added instructions for Siemens
Atellica Im & CC racks
Revisions
This short guide contains information for the usage of rack holders on the
cobas p 512 pre-analytical system (64x) and the
cobas p 612 pre-analytical system (63x).
Short guide for the usage of rack holders
3
Table of contents
Supported sample tubes ............................................................................................................................. 6
Supported racks ......................................................................................................................................... 6
Loading the rack holder with racks ........................................................................................................... 7
To load one 55 position rack on a rack holder .......................................................................................... 8
To load up to three 15 position racks on a rack holder.............................................................................. 9
Short guide for the usage of rack holders
4
Affected systems
Systems
Link to latest version of
user documentation
Applicable
software version
Change
description
cobas p 512
(SN 64xxxxxx)
cobas p 612
(SN 63xxxxxx)
Operator's Manual cobas
p 512 (64x)
User Guide cobas p 612
(63x)
2.0.6 or higher
2.0.6 or higher
Instructions for the
usage of rack
holders
Table 1: Affected systems
Roche recommends that you familiarize yourself with the new and/or revised content
provided in this short guide.
If you print these pages, Roche recommends printing them single sided. In this way,
you can easily insert the new and/or
revised content in the appropriate locations in
the existing document.
Safety information
CAUTION
Pinching hazard
Closing the drawer may cause pinching
.
•
Close the drawer slowly and carefully to avoid pinching your fingers between the
drawers.
•
Do not bypass security installations.
CAUTION
Incorrect tube position
Incorrect positioning of the sample tubes causes problems set
ting them down during
sorting.
Tubes may tilt and the
contents may spill.
•
Manually check if the sample tubes are completely inserted in the rack. They should
rest against the bottom of the rack.
•
Use only racks with undamaged spring inserts.
• Check the position and the fill level of all trays and tubes.
Short guide for the usage of rack holders
5
WAR
NING
Risk of infection
Sample material and all unit parts
that come into contact with the sample material are
infectious and harmful to health.
Wrong labelling or a sticky tube may cause
the tube to crash into the LLD housing. This
may cause sample and system contamination.
•
Always wear gloves when working on the system.
• Apply the label as per the instructions in the operator's manual or the user guide.
Short guide for the usage of rack holders
6
Rack holder for Siemens Atellica IM & CC racks
Figure 1: Rack holder for Siemens Atellica IM & CC racks
Supported sample tubes
The sample tubes listed in the RDA Qualified Tube List for cobas p x71, p x12 LCP1 and
BLM are qualified for the Siemens Atellica IM & CC rack holder.
Supported racks
Only Siemens Atellica IM & CC racks are qualified for this rack holder.
Either one 55 position rack or up to three 15 position racks can be loaded into the rack
holder.
Short guide for the usage of rack holders
7
Loading the rack holder with racks
Figure 2: Siemens Atellica IM & CC rack holder
A Retaining brackets B Limit stops
C Loading aid
Short guide for the usage of rack holders
8
To load a 55 position rack onto a rack holder
1 Load the rack onto the rack holder.
Make sure that the rack is firmly seated on the rack holder.
Figure 3: Load rack holder
2 Close retaining bracket.
Figure 4: Close retaining bracket
Short guide for the usage of rack holders
9
Figure 5: Loaded rack holder
The loading of the rack holder is completed.
To load up to three 15 position racks onto a rack holder
1 Load up to three racks onto the rack holder.
Make sure that the racks are firmly seated on the rack holder.
Figure 6: Load rack holder
2 Close retaining bracket.
Short guide for the usage of rack holders
10
Figure 7: Close retaining bracket
Figure 8: Loaded rack holder
The loading of the rack holder is completed.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Roche cobas p 512 LCP1 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Roche cobas p 612 LCP1 User manual
-
-
-
Roche cobas 8100 AliquoterModule User manual
-
-
-
-
-
-