Greenheck vari-green Quick start guide

Greenheck
Brand
Greenheck
Model
vari-green
Type
Quick start guide

This manual is also suitable for

Greenheck 484390 Single/Three Phase Vari-Green Motor is an energy-efficient and versatile motor designed for a wide range of applications including variable air volume (VAV) systems, exhaust fans, and make-up air units. The motor is preprogrammed to run from either an on-board dial or a 0-10 VDC control signal, providing precise speed control. It also features a motorized backdraft damper, which can be wired to close when a run command is given.

The motor has a totally enclosed fan-cooled (TEFC) enclosure, which protects it from dust, dirt, and moisture. It is also equipped with an integral transducer, which allows it to be used in constant pressure or airflow control applications.

Greenheck 484390 Single/Three Phase Vari-Green Motor is an energy-efficient and versatile motor designed for a wide range of applications including variable air volume (VAV) systems, exhaust fans, and make-up air units. The motor is preprogrammed to run from either an on-board dial or a 0-10 VDC control signal, providing precise speed control. It also features a motorized backdraft damper, which can be wired to close when a run command is given.

The motor has a totally enclosed fan-cooled (TEFC) enclosure, which protects it from dust, dirt, and moisture. It is also equipped with an integral transducer, which allows it to be used in constant pressure or airflow control applications.

Quick Start Guide
Single/Three Phase Vari-Green
®
Motor
Vari-Green Motor Quick Start Guide
When delivered, the Vari-Green Motor is pre-
programed to run from either an on-board dial or a
0-10 VDC control signal. A 0-1.99 Volt control signal
will be received as a “stand-by” command.
A run command is acknowledged, as well as a
speed reference from 2-10 V.
For more information about this
Vari-Green Motor, please review
the Installation, Operation and
Maintenance Manual found by
following this QR code:
www.greenheck.com/vari-green/vari-green-motors
Step 1
Connect the power supply. Verify Input Voltage and
phase matches nameplate of motor/drive.
THREE PHASE
L1
L2
L3
L1
L2
L3
L1
L2
L3
L
N
DISCONNECT
POWER
DISCONNECT
POWER
SINGLE PHASE
THREE PHASE
L1
L2
L3
L1
L2
L3
L1
L2
L3
L
N
DISCONNECT
POWER
DISCONNECT
POWER
SINGLE PHASE
Step 2
Connect control wiring to the control terminal.
DIAL ON-BOARD
RED
WHITE
BLACK
*JUMPER
+24V, 100mA
D1, ENABLE
2D
D3/A2
+10VDC
A1
COMMON
AO/DO OUTPUT
COMMON
MODBUS RTU–
MODBUS RTU+
+24V, 100mA
D1, ENABLE
2D
D3/A2
+10VDC
A1
COMMON
AO/DO OUTPUT
COMMON
MODBUS RTU–
MODBUS RTU+
RED
WHITE
0-10V CONTROL SIGNAL
*JUMPER
COMMON
0-10VDC CONTROL
NOTE: Factory default settings:
1. Terminal 2 is set as an ENABLE command. From the
factory there is a jumper from terminal 1 to 2. A START/
STOP switch can be used between these terminals to
ENABLE/DISABLE the drive.
2. When this Vari-Green Motor is ordered in a 0-10 VDC
Control configuration, the motor is shipped with a jumper
between terminal 5 and 6. This will run the motor at full
speed when power is connected. Remove this jumper
before landing 0-10 VDC control wires.
Step 3
Install motorized backdraft damper wiring, if
applicable. The relay RL-1 is set from the factory to
close when a run command is given.
(DAMPER POWER SOURCE)
N
LINE
MOTORIZED DAMPER
RL–1A
RELAY COMMON
RL–1B
RELAY N.O. COMMON
250VAC, 6A
30VDC, 5A
Step 4
Apply power to unit. If a control signal
is present, the RL-1 relay will close and
the motor will ramp up to the
referenced speed. If a jumper is
installed between terminals 5 and 6,
the motor will go to 100%.
Step 5
Balance the fan. Whether changing the position of
the on-board dial or adjusting the control voltage,
the fans speed can be set from the minimum to the
motor’s factory programmed maximum speed.
Re-apply the motor cover.
Quick Start Guide
Single/Three Phase Vari-Green
®
Motor
484390 • Single/Three Phase Vari-Green Motor, Rev. 2, November 2020 • Copyright © 2020 Greenheck Fan Corp.
Step 6
Review the Installation, Operation and Maintenance
Manual for the fan for any specific installation
questions. The manual is shipped with the fan,
and can also be found at www.greenheck.com or
by scanning the QR code located within the drive
compartment.
Electrical Data
Supply Voltage Range
110 Volt Units, 99-126 V
230 Volt Units, 180-264 V
400 Volt Units, 342-528 V
Short Circuit Capacity
5kA Without Fused Disconnect
100kA With Fused Disconnect
Control Terminal Wiring
Maximum Size 0.05-0.5mm2 / 20-26 AWG
RL-1 Relay
Relay N.O. Contact 250VAC, 6A/30VDC, 5A
Motor Enclosure
Totally Enclosed Fan Cooled, IP54
WARNING
• Do not remove the drive cover for wiring or
periodic inspections while power is applied or
the unit is in operation. Electric shock may occur
from the exposed terminals.
• Wait at least 1 minute after disconnecting the
input power before performing any wiring tasks
and/or periodic inspections of the drive.
• Operate the Vari-Green motor and control
devices with dry hands.
• Do not use this device if power or motor cable is
damaged.
• As this is a permanent magnet motor, this motor
will generate voltage when the shaft is rotated.
Shaft must be locked out for safe servicing.
CAUTION
• Disconnect the input power if the Vari-Green
motor has been damaged. Failure to do so
may result in fire and/or secondary damage or
accidents.
• Do not touch the Vari-Green motor immediately
after shutting down or disconnecting it. It can
remain hot for a few minutes. Bodily injuries such
as skin-burn or damage may occur.
• Do not apply power to a damaged Vari-Green
motor or to a Vari-Green motor that is missing
parts.
• Do not allow lint, paper, wood chips, dust,
metallic chips or other foreign material into the
drive as it may cause fire or accident.
Vari-Green Controls
Vari-Green Controls all use a 0-10 VDC control signal
to provide a speed reference to Vari-Green Motors.
See below for typical Vari-Green wiring. Reference
the individual controls Installation, Operation and
Maintenance Manual for programing, wiring and
troubleshooting of that control.
+24V, 100mA
D1, ENABLE
2D
D3/A2
+10VDC
A1
COMMON
AO/DO OUTPUT
COMMON
MODBUS RTU–
MODBUS RTU+
GND
POWER
IN
V+
CONTROL OUT
REF OUT
DIGITAL
OUTPUT
OVERRIDE
REMOTE SET
POINT
CONSTANT PRESSURE / AIRFLOW
CONTROL – INTEGRAL TRANSDUCER
  • Page 1 1
  • Page 2 2

Greenheck vari-green Quick start guide

Greenheck
Brand
Greenheck
Model
vari-green
Type
Quick start guide
This manual is also suitable for

Greenheck 484390 Single/Three Phase Vari-Green Motor is an energy-efficient and versatile motor designed for a wide range of applications including variable air volume (VAV) systems, exhaust fans, and make-up air units. The motor is preprogrammed to run from either an on-board dial or a 0-10 VDC control signal, providing precise speed control. It also features a motorized backdraft damper, which can be wired to close when a run command is given.

The motor has a totally enclosed fan-cooled (TEFC) enclosure, which protects it from dust, dirt, and moisture. It is also equipped with an integral transducer, which allows it to be used in constant pressure or airflow control applications.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents