2. Acme Packet
  3. Net-Net 2610

Acme Packet Net-Net 2610 Quick Installation

  • Hello! I am an AI chatbot trained to assist you with the Acme Packet Net-Net 2610 Quick Installation. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Net-Net OS-E and 2610/2620
installation references
• USB Creation and
Commissioning Instructions
•Release Notes
• System Installation and
Commissioning Guide
• Slide Rail Kit Installation
Net-Net® 2610/2620 Quick Installation
What’s inside the box?
• Net-Net 2610 or 2620
• Power, console cables and
related hardware, rack mounting
kits
Laptop PC
RJ-45 adapter
RJ-45
RS-232D Serial B port
DB-9 serial cable
Connect PC or terminal to serial port (ttyS1),
or go to step 4b.
Console settings:
115200 bps
8 data bits
No parity
1 stop bit
No flow control
C
onsole settings:
115200
b
p
s
8
data
b
i
ts
No parit
y
1 stop
b
i
t
N
o
f
l
o
w
co
n
t
r
o
l
4a
Connect VGA console and keyboard for
local management.
Keyboard
Console
Keyboard and console ports
Ethernet port mapping -- Left to right, top to bottom
1 = eth0 5 = eth4
2 = eth1 6 = eth5
3 = eth2 7 = eth6
4 = eth3 8 = eth7
12
Ethernet port mapping -- Left to right, top to botto
m
1 = e
h
= e
h
2
= eth1 6 = eth
5
3
= et
h
2 7 = et
h
6
4
= e
t
h
3
8
= e
t
h
7
4b
Install network cables for connectivity to
communications servers and the external network.
Remote system management over Telnet, SSH,
and Web.
eth0
eth1
Ethernet
switches
Telnet/CLI session
Internet
Web management session
5
OR
1
Carefully remove the Net-Net 2000
Series from the shipping container,
along with the accessories box.
Install the chassis in a compatible rack.
a. Select the appropriate installation kit
for the type of rack you are using; select
either the slide rail kit or the fixed mount
kit.
b. Refer to the instructions included with
each kit for installation details.
c. Install multiple systems in the rack
from the bottom up.
d. Install the front bezel after
completing Step 6.
2
Connect the AC power cords.
AC power cord
Power receptacle (North America)
or compatible power source
Insert plug end into AC
cable receptacle.
3
Proprietary & Confidential
Remove the front bezel (if installed), insert the USB stick that you created,
then turn on the system power. Check system LEDs.
2. Press power button.
See the System Installation and Commissioning Guide for LED information.
Replace the bezel and secure with the supplied locking key,
if desired.
Warning: DO NOT remove the USB stick until the system has
completed the bootup sequence, which may take up to ten minutes.
1. Insert USB stick
Follow the steps covered in the USB Creation and Commissioning
Instructions for information on creating a USB stick from the Acme Packet
Net-Net OS-E software download. Included with the software download
in PDF format, you will need these instructions to commission the system.
F
ollow the steps covered in the
US
B
C
reation and
C
ommissioning
I
n
s
tr
uc
ti
o
n
s
for information on creating a USB stick from the Acme Packet
s
N
et-Net OS-E software download. Included with the software download
i
n PDF
f
ormat, you will need these instructions to commission the system.
6
Configure the Net-Net OS-E software, SIP servers and phones,
sessions and policies.
Refer to the following Net-Net OS-E documents, available as
downloads in PDF format:
Release Notes
USB Creation and Commissioning Instructions
System Installation and Commissioning Guide
Using the Net-Net OS-E Management Tools
System Administration Guide
Session Services Configuration Guide
Objects and Properties Reference
Network Interface Card Installation
System Operations and Troubleshooting
8
Net-Net® 2610/2620 Quick Installation (cont.)
Start the CLI and run the setup script to enable and configure the management interface, establish
an IP route (if setting up remotely), enable Web management access, and customize the CLI prompt. Every
Net-Net 2000 Series system has a minimum of two Ethernet interfaces.
Any Ethernet interface can be used for management traffic. However, Acme Packet recommends the
use of eth1, as eth0 is reserved for fault-tolerant clustering with other Net-Net 2000 Series platforms.
Management traffic is also supported on any interface that is carrying private or public network traffic.
This means that it would be possible to use eth1 to carry SIP traffic and management traffic.
NN-OS-E> config setup
set box\hostname: local
config box\interface: eth1
set box\interface eth1\ip a\ip-address: <ipAddress/mask>
config box\interface eth1\ip a\ssh (y or n)? y
config box\interface eth1\ip a\web (y or n)? y
config box\interface eth1\ip a\routing\route: <routeName>
set box\interface eth1\ip a\routing\route <routeName>\gateway:
<ipAddress>
set box\cli\prompt: NN-OS-E 2620>
Do you want to commit this setup script (y or n) y
Do you want to update the startup configuration (y or n)? y
NN-OS-E 2620>
7
Acme Packet, Inc.
71 Third Avenue
Burlington, MA 01803 USA
t 781-328-4400
f 781-425-5077
http://www.acmepacket.com
Last Updated: November 2009
Document Number: 400-1003-36
NN2600
Net-Net 2610/2620 Quick Installation
2009 Acme Packet, Inc.
All rights reserved
Proprietary & Confidential
/