meitav-tec CTU-4524-3S-FC-Super Product information

Brand
meitav-tec
Model
CTU-4524-3S-FC-Super
Type
Product information
N L V1 X1 DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8 12378AO1 0
DI1 0DI3 0DI2 DI5 0DI4 DI7 0DI6 DI8 12V T1 0T2 0T3 0AI1 0AI2 5VDC A B
ON
12345678
ON
1234
12Vdc supply voltage –
option (30mA max)
Fan speeds
Return air sensor
Change over sensor
Indoor coil sensor
Communication cable
2x22AWG
Twisted, Shielded
Main Input
24Vac
Fan low
Fan medium
Fan high
24Vac, 3A Panel output
(option)
MAC Address
DIP switch (S1) Configuration
DIP switch (S2)
Power LED
Not in use
ON
1234
DIP switch Configuration (S2)
S2.1 – Fan ON / Auto fan configuration in cool/heat
ON - Auto fan in Cool
OFF - Fan ON (always) in Cool
S2.2 – 2-pipe / 4-pipe system
ON - 4-pipe
OFF - 2-pipe
S2.3 – ON - Auto fan in Heat
OFF - Fan ON (always) in Heat
S2.4 – “End of network” configuration
ON - End of network
OFF - Not end of network
Date:
Title:Drawn: M.Ruchansky
Checked: O.Volovitch
Approved: A.Samocha
CTU4524-3S-FC-SUPER
13.10.2010
meitav tec
Tel: +972-3-9626462
Fax: +972-3-9626620
e-mail: support@meitavtec.com File: CTU4524-3S-FC-SUPER.vsd
Digital Inputs
Default
Print name: PS-2600-ASU
Temperature Sensors Logic
T1,0 - Return air sensor
The ambient (room) temperature can be sensed via the return air sensor.
T2,0 - Change-over sensor
Mode is automatically selected, based on the water temperature sensed by T2 (2-pipe system
only) T2 > 30°C / 86°F Heat , T2 < 20°C / 68°F Cool
T3,0 - Indoor coil sensor
Soft-start in Heat
When T3 rises above (or equals) 36°C/97°F The indoor fan will start working (according to
FAN ON or AUTO FAN state)
When the temperature drops below 32°C/90°F The indoor fan will turn OFF.
*When T3 is not connected:
- If AUTO FAN is selected, the indoor fan will start working 30 seconds after demand for heat.
- If FAN ON is selected, the indoor fan will work continuously.
Occupancy
Sensor
2. DI5,0 -Fault 1 input (N.C.)
When open – all outputs OFF (no delay)
3. DI7,0 -Fan speeds
Software name: 10406202
Check sum : 7086
13.10.10
1 Original (with BT)
NNNN
Input
“N”
AO2
Heat 24Vac, 1A
o
RS485 RS485
Modbus ProtocolModbus Protocol
Cool 24Vac, 1A
Pump Output
24Vac, 1A
Not in use
Important !
Disconnect power to the main
board before making any
changes to DIP switches/
Jumpers, wiring the unit and/or
connecting the wall panel.
Digital Inputs Not in use
1. DI1,0 DI2,0 DI3,0 DI4,0 DI6,0 –Digital Inputs
Normally open (N.O.)Active when close.
Only for indication through communication.
4. DI8,0 -Occupancy Sensor
One of 3 modes (set by communication):
1 Auto: When the DI8 input (N.C) is open for 10
minutes, all outputs turn Off.(Default)
2 Start/Stop
3 Occupied/Non occupied (Economy mode)
Fault 1
Digital Inputs
Open – 3 Speeds, Close – 1 Speed
FMH/X500/02;
ETN/X500/02;
IRP/X500/02
14.11.102New S/W
  • Page 1 1

meitav-tec CTU-4524-3S-FC-Super Product information

Brand
meitav-tec
Model
CTU-4524-3S-FC-Super
Type
Product information
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents