Eneo NXC-1302M Installation Operation User Manual

1

INSTALLATION / OPERATION / USER’S MANUAL

NXC Series

MEGAPIXEL NETWORK CAMERA

2

3

WARNINGS AND CAUTIONS:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR

MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR

OTHER OPENINGS ON THE EQUIPMENT.

CAUTION

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated "dangerous voltage" within the product's enclosure

that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the product.

PRECAUTIONS

Safety ---------------------------------- Installation -----------------------------

Cleaning ----------------------------------

CAUTION

RISK OF ELECTRNIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Should any liquid or solid object fall into the cabinet,

unplug the unit and have it checked by the qualified

personnel before operating it any further.

Unplug the unit from the wall oulet if it is not going to

be used for several days or more. To disconnect the

cord, pull it out by the plug. Never pull the cord itself.

Allow adequate air circulation to prevent internal heat

build-up. Do not place the unit on surfaces (rugs,

blankets, etc.) or near materials(curtains, draperies)

that may block the ventilation holes.

Height and vertical linearity controls located at the rear

panel are for special adjustments by qualified

personnel only.

Do not install the unit in an extremely hot or humid place

or in a place subject to excessive dust, mechanical

vibration.

The unit is not designed to be waterproof.

Exposure to rain or water may damage the unit.

Clean the unit with a slightly damp soft cloth.

Use a mild household detergent. Never use strong

solvents such as thinner or benzene as they might

damage the finish of the unit.

Retain the original carton and packing materials for safe

transport of this unit in the future.

4

FCC COMPLIANCE STATEMENT

CE COMPLIANCE STATEMENT

FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO

COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF

THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE

PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS

OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES,

AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN

ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL

INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A

RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE

THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN

EXPENSE.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE

PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO

OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME NMB-003 DU

CANADA.

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

5

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS -- All the safety and operating instructions should be read before the

appliance is operated.

2. RETAIN INSTRUCTIONS -- The safety and operating instructions should be retained for future

reference.

3. CLEANING -- Unplug video monitor or equipment from the wall outlet before cleaning. Do not

use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4. ATTACHMENTS -- Do not use attachments not recommended by the video monitor or

equipment manufacturer as they may result in the risk of fire, electric shock or injury to persons.

5. WATER AND MOISTURE -- Do not use video monitor or equipment near water - for example,

near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming

pool or the like.

6. ACCESSORIES -- Do not place video monitor or equipment on an unstable cart, stand or table.

The video monitor or equipment may fall causing serious injury to a child or adult and serious

damage to the equipment. Wall or shelf mounting should follow the manufacturer's instructions

and should use a mounting kit approved by the manufacturer.

6A. Video monitor or equipment and cart combinations should be moved with care.

Quick stops, excessive force and uneven surfaces may cause the equipment and cart

combination to overturn.

7. VENTILATION -- Slots and openings in the cabinet at the back or bottom are provided for

ventilation and to ensure reliable operation of the video monitor or equipment and to protect it

from overheating. These openings must not be blocked or covered. The openings should never

be blocked by placing the video monitor or equipment on a bed, sofa, rug, or other similar

surface. Video monitor or equipment should never be placed near or over a radiator or heat

register. Video monitor or equipment should not be placed in a built-in installation such as a

bookcase unless proper ventilation is provided.

8. POWER SOURCES -- Video monitor or equipment should be operated only from the type of

power source indicated on the marking label. If you are not sure of the type of power supplied to

your home, consult your video monitor or equipment dealer or local power company. For video

monitor or equipment designed to operate from battery power refer to the operating instructions.

9. GROUNDING OR POLARIZATION -- This video monitor may be equipped with a polarized

alternating - current line plug (a plug having one blade wider than the other). This plug will fit into

the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully

into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Alternate

Warnings - This video monitor is equipped with a three-wire grounding-type plug, a plug having

a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety

6

feature. If you are unable to insert the plug into the outlet, contact your electrician to replace

your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

10. POWER CORDS -- Do not allow anything to rest on the power cord. Do not locate video monitor

or equipment where the cord will be abused by persons walking on it.

11. HEED WARNINGS -- Follow all instructions marked on the video monitor or equipment.

12. LIGHTNING -- For added protection for video monitor or equipment during a lightning storm, or

when it is left unattended and unused for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent damage to the video product due to

lightning and power-line surges.

13. OVERLOADING --Do not overload wall outlets and extension cords as this can result in a risk of

fire or electric shock.

14. OBJECT AND LIQUID ENTRY -- Never push objects of any kind into video monitor or

equipment through openings as they may touch dangerous voltage points or short-out parts that

could result in a fire or electric shock. Never spill liquid of any kind on the product.

15. SERVICING -- Do not attempt to service video monitor or equipment yourself as opening or

removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

16. DAMAGE REQUIRING SERVICE -- Unplug video monitor or equipment from the wall outlet and

refer servicing to qualified service personnel under the following conditions:

A. When the power-supply cord or the plug has been damaged.

B. If liquid has spilled or objects have fallen into the video product.

C. If the video product has been exposed to rain or water.

D. If the video product does not operate normally by following the operating instructions, adjust

only those controls that are covered by the operating instructions as an improper adjustment

of other controls may result in damage and will often require extensive work by a qualified

technician to restore the video product to its normal operation.

E. If the video product has been dropped, or the cabinet damaged.

F. When the video product exhibits a distinct change in performance -- this indicates a need for

service.

17. REPLACEMENT PARTS -- When replacement parts are required, be sure the service

technician has used replacement parts specified by the manufacturer or that have the same

characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or

other hazards.

18. SAFETY CHECK -- Upon completion of any service or repairs to this video product, ask the

service technician to perform safety checks to determine that the video product is in proper

operating condition.

19. FIELD INSTALLATION -- This installation should be made by a qualified service person and

should conform to all local codes.

7

CONTENTS

DESCRIPTION ----------------------------------------------------------------------------------------------------11

Models ---------------------------------------------------------------------------------------------------11

Key Features --------------------------------------------------------------------------------------------11

Components --------------------------------------------------------------------------------------------12

Camera Layout -----------------------------------------------------------------------------------------13

INSTALLATION ---------------------------------------------------------------------------------------------------15

Before Installation -------------------------------------------------------------------------------------15

Starting Installation ------------------------------------------------------------------------------------15

DC Auto Iris Lens Installation & Adjustment -------------------------------------------------------16

Audio Connection --------------------------------------------------------------------------------------17

Alarm Connection --------------------------------------------------------------------------------------17

OPERATION -------------------------------------------------------------------------------------------------------18

Minimum conditions for using web browser -------------------------------------------------------18

Accessing the IP camera ------------------------------------------------------------------------------18

Main Menu ----------------------------------------------------------------------------------------------19

LIVE VIEW --------------------------------------------------------------------------------------------------------20

Live Video Page Icons ---------------------------------------------------------------------------------21

SETUP -------------------------------------------------------------------------------------------------------------22

Users -----------------------------------------------------------------------------------------------------23

Network -------------------------------------------------------------------------------------------------26

Image ----------------------------------------------------------------------------------------------------27

Audio -----------------------------------------------------------------------------------------------------29

Date & Time --------------------------------------------------------------------------------------------31

Live View – Source ------------------------------------------------------------------------------------32

Image – Basic ------------------------------------------------------------------------------------------35

Image – AE & AWB ------------------------------------------------------------------------------------36

Image – Day & Night ----------------------------------------------------------------------------------39

Video & Image – Stream1 ----------------------------------------------------------------------------41

Video & Image – Stream2 ----------------------------------------------------------------------------43

Video & Image – Stream3 ----------------------------------------------------------------------------46

Video & Image – Stream4 ----------------------------------------------------------------------------49

Video & Image – Webcasting ------------------------------------------------------------------------53

Audio – Basic -------------------------------------------------------------------------------------------54

Event In – Alarm-In ------------------------------------------------------------------------------------56

Event In – Manual Trigger ----------------------------------------------------------------------------58

Event In – VMD Stream1 ----------------------------------------------------------------------------59

Event In – VMD Stream3 -----------------------------------------------------------------------------61

8

Event In – VMD Stream4 -----------------------------------------------------------------------------63

Event Out – SMTP --------------------------------------------------------------------------------------65

Event Out – FTP& JPEG -------------------------------------------------------------------------------68

Event Out – Audio Alert -------------------------------------------------------------------------------69

Event Out – Audio Alert – Audio Recorder -------------------------------------------------------70

Event Out – PTZ Preset--------------------------------------------------------------------------------72

Event Out – SD Record --------------------------------------------------------------------------------73

Event Map -----------------------------------------------------------------------------------------------75

Event Map – Add ---------------------------------------------------------------------------------------76

Device – PTZ --------------------------------------------------------------------------------------------77

Device – RS485 -----------------------------------------------------------------------------------------78

SD Playback – SD Playback List View ---------------------------------------------------------------79

Security – Users ----------------------------------------------------------------------------------------81

Security – HTTPS --------------------------------------------------------------------------------------84

Security – IP Filtering ----------------------------------------------------------------------------------86

Date & Time ------------------------------------------------------------------------------------------- 87

Network – Basic ----------------------------------------------------------------------------------------89

Network – DDNS ---------------------------------------------------------------------------------------91

Network – RTP -----------------------------------------------------------------------------------------92

Network – UPnP ----------------------------------------------------------------------------------------94

Network – QoS ----------------------------------------------------------------------------------------95

Language -----------------------------------------------------------------------------------------------96

Maintenance --------------------------------------------------------------------------------------------97

Support --------------------------------------------------------------------------------------------------99

About ---------------------------------------------------------------------------------------------------100

Technical Specifications ---------------------------------------------------------------------------------------101

Models --------------------------------------------------------------------------------------------------101

General -------------------------------------------------------------------------------------------------101

Electrical / Connector --------------------------------------------------------------------------------101

Mechanical ---------------------------------------------------------------------------------------------102

Video ---------------------------------------------------------------------------------------------------102

Audio ---------------------------------------------------------------------------------------------------103

System Integration -----------------------------------------------------------------------------------103

Environmental -----------------------------------------------------------------------------------------103

Physical ------------------------------------------------------------------------------------------------104

Troubleshooting -------------------------------------------------------------------------------------------------105

Upgrading the Firmware -----------------------------------------------------------------------------105

General Troubleshooting ----------------------------------------------------------------------------105

9

LIST of ILLUSTRATIONS

Figure 1. 4-pin iris driver connector ---------------------------------------------------------------------------16

Figure 2. DC auto iris Lens connection -----------------------------------------------------------------------16

Figure 3. Audio connection -------------------------------------------------------------------------------------17

Figure 4. Alarm connector --------------------------------------------------------------------------------------17

Figure 5. Main menu ---------------------------------------------------------------------------------------------19

Figure 6. Main Live View Page ---------------------------------------------------------------------------------20

Figure 7. Basic Configuration -----------------------------------------------------------------------------------22

Figure 8. Basic Configuration / Users -------------------------------------------------------------------------23

Figure 9. Basic Configuration / Users / Add User -----------------------------------------------------------24

Figure 10. Basic Configuration / Users / Modify User -------------------------------------------------------25

Figure 11. Basic Configuration / Network --------------------------------------------------------------------26

Figure 12. Basic Configuration / Image -----------------------------------------------------------------------27

Figure 13. Basic Configuration / Audio ------------------------------------------------------------------------29

Figure 14. Basic Configuration / Date & Time ---------------------------------------------------------------31

Figure 15. Live View / Source ----------------------------------------------------------------------------------32

Figure 16. Video & Image / Image – Basic ------------------------------------------------------------------35

Figure 17. Video & Image / Image – AE & AWB ------------------------------------------------------------36

Figure 18. Video & Image / Day & Night ---------------------------------------------------------------------39

Figure 19. Video & Image / Stream1 -------------------------------------------------------------------------41

Figure 20. Video & Image / Stream2 -------------------------------------------------------------------------43

Figure 21. Video & Image / Stream2 ROI setting -----------------------------------------------------------45

Figure 22. Video & Image / Stream3 -------------------------------------------------------------------------46

Figure 23. Video & Image / Stream3 ROI setting -----------------------------------------------------------48

Figure 24. Video & Image / Stream4 -------------------------------------------------------------------------49

Figure 25. Video & Image / Stream4 ROI setting -----------------------------------------------------------52

Figure 26 Video & Image / Webcasting ----------------------------------------------------------------------53

Figure 27. Audio / Basic ----------------------------------------------------------------------------------------54

Figure 28. Event / Event In – Alarm In -----------------------------------------------------------------------56

Figure 29. Event / Event In – Manual Trigger ---------------------------------------------------------------58

Figure 30. Event / Event In – VMD Stream1 -----------------------------------------------------------------59

Figure 31. Event / Event In – VMD Stream3 -----------------------------------------------------------------61

Figure 32. Event / Event In – VMD Stream4 -----------------------------------------------------------------63

Figure 33. Event / Event Out – SMTP (Email) ---------------------------------------------------------------65

Figure 34. Event / Event Out – FTP & JPEG -----------------------------------------------------------------67

Figure 35. Event / Event Out – Audio Alert ------------------------------------------------------------------69

Figure 36. Event / Event Out – Audio Alert / Audio Recorder----------------------------------------------70

Figure 37. Event / Event Out – Audio Alert / ARecorder window -----------------------------------------70

Figure 38. Event / Event Out – Audio Alert / Encode setup -----------------------------------------------71

Figure 39. Event / Event Out – PTZ Preset ------------------------------------------------------------------72

Figure 40. Event / Event Out – SD Record -------------------------------------------------------------------73

Figure 41. Event / Event Map ----------------------------------------------------------------------------------74

Figure 42. Event / Event Map – Add --------------------------------------------------------------------------75

10

Figure 43. Device / PTZ------------------------------------------------------------------------------------------77

Figure 44. Device / RS485---------------------------------------------------------------------------------------78

Figure 45. SD Playback / Playback List View------------------------------------------------------------------79

Figure 46. SD Playback / Playback List View – Playback----------------------------------------------------80

Figure 47. System / Security – Users -----------------------------------------------------------------------81

Figure 48. System / Security – Users / Add User -----------------------------------------------------------82

Figure 49. System / Security – Users / Modify User --------------------------------------------------------83

Figure 50. System / Security – HTTPS ------------------------------------------------------------------------84

Figure 51. System / Security – IP Filtering -------------------------------------------------------------------86

Figure 52. System / Date & Time ------------------------------------------------------------------------------87

Figure 53. System / Network – Basic -------------------------------------------------------------------------89

Figure 54. System / Network – DDNS ------------------------------------------------------------------------91

Figure 55. System / Network – RTP ---------------------------------------------------------------------------92

Figure 56. System / Network – UPnP -------------------------------------------------------------------------94

Figure 57. System / Network – QoS -------------------------------------------------------------------------95

Figure 58. System / Language ---------------------------------------------------------------------------------96

Figure 59. System / Maintenance -----------------------------------------------------------------------------97

Figure 60. System / Support -----------------------------------------------------------------------------------99

Figure 61. About ------------------------------------------------------------------------------------------------100

11

DESCRIPTION

-------------------------------------------------------------------------------------------------------------------------------------

The NXC Series camera is an internet protocol based megapixel network camera with a built-in web

based viewer on Internet Explorer®. The camera has a connection feature for third-party

applications and compatible with supplied Utility software for easy installation and Client software to

search, configure, manage, live view, record and playback.

The camera supports dual compression formats and multiple streaming simultaneously. The two

standard compression formats include H.264 and MJPEG. The multiple streams can be configured to

a variety of resolutions, bit rates and frame rates.

The camera uses 1/2.5 inch CMOS sensor and complies with CS mount lens and also supports PoE

(Power over Ethernet), DC12V, and AC24V.

Models

NXC-1401M NXC Series, 1 Megapixel, 30ips@1280x720

NXC-1402M NXC Series, 2 Megapixel, 15ips@1600x1200

NXC-1301M NXC Series, 1 Megapixel, 30ips@1280x720, Day/Night

NXC-1302M NXC Series, 2 Megapixel, 15ips@1600x1200, Day/Night

Key Features

- HDTV Video Quality

The NXC Series are capable of providing the outstanding image quality with HDTV performance and

profiles (High, Main, and Baseline) in H.264 compression.

- Multiple Streaming

Each stream can be programmed independently and transmitted using different configurations.

- ROI (Region of Interest)

ROI features that transmit specially selected area in the primary stream using different FPS,

Resolution, Bit Rates and Picture Quality.

- Easy Focus

Easy Focus helps to reduce the installation efforts especially video image focusing of the camera.

- Dual Codec (H.264, MJPEG)

The NXC Series supports two standard compressions formats H.264 and MJPEG.

12

- Digital PTZ

Supports maximum 10x digital zoom.

- Intelligent Video Motion Detection

The NXC Series offers intelligent & sophisticated video motion detection for each multiple streams.

- Triple Power (Power over Ethernet, DC12V, AC24V)

This camera supports Power over Ethernet (PoE), which supplies power to the camera through the

network. If the network has no PoE, connect a DC12V or AC24V power connector.

- Day and Night

The NXC Series provide clear monitoring images even in low light conditions using IR-cut filter.

- SD Local Recording

The NXC Series provides local video recording function. When camera detects video motion or

alarm events or manual trigger, it can record video stream by itself.

- Voice Alert Linked to Alarm Detection

The NXC Series can play the audio file stored in the camera in synchronization with alarm detection

by the sensor input or the motion detection function.

- Network Flow Control

The NXC Series provides a flow control function which enhances network efficiency by significantly

restricting user video streams with designating the maximum bandwidth.

- ONVIF Certificate

The NXC Series network camera complies with the ONVIF certificate. ONVIF (Open Network Video Interface

Forum) is an open industry forum for the development of a global standard for the interface of network video

products.

Components

Quantity Description

1 Camera

1 Installation CD

1 C- Mount Ring

1 Auto DC-Iris Connector

NOTE

Lens, installation hardware and Adapter for DC12V / AC24V are not supplied.

13

Camera Layout

RJ-45 connector: Supplies power to the camera through the network using PoE. If PoE is

not available, supplies DC12V or AC24V power source to the POWER connector.

ETHERNET link indication LED: Flashes green to indicate that data is being TX/RX by the

camera.

ETHERNET activity indication LED: Glows solid amber to indicate that a live connection is

established.

STATUS indication LED: Flashes amber about one time per second to indicate normally

working and flashes green about 2~3 time per second while upgrade.

POWER indication LED: Glows solid red if power is supplied properly.

SPEAKER connector: Connect external speaker for audio output.

MIC connector: Supplies external microphone as an audio input source.

POWER connection: Supplies DC12V or AC24V as the power source comply with Class2.

14

RESET button: Restores the camera’s factory default settings. This button is recessed. Use a

small tool, such as a paper clip, to press the reset button.

Please take steps as follows:

1.

Power off

2.

Press and hold the RESET button

3.

Supply the camera with power

4.

Hold the RESET button for 15 seconds

ALARM connection: Connect one or two physical alarm input signal into the device and one

alarm output signal that can be used to control an external alarm circuit.

BNC connector: Connect BNC cable for composite video output.

INSTALLATION TOP STAND connector: 0.25 Inch (0.64cm) UNC-20 screw, top of camera

housing.

INSTALLATION BOTTOM STAND connector: 0.25 Inch (0.64cm) UNC-20 screw, bottom

of camera housing.

FOCUS ADJUSTING / FIXING screw: Tighten this screw after focus the lens of a camera.

AUTO IRIS LENS connector: Connect the DC auto iris lens 4-pin connector into this

connector to control the amount of light allowed through the lens.

CS MOUNT LENS: connection: Attach the CS type lens.

RS485 connection: Connect RS485 compatible device for PTZ control.

SD Card: Insert SD card for local recording.

15

INSTALLATION

-------------------------------------------------------------------------------------------------------------------------------------

Before Installation

Before installing the camera, thoroughly familiarize yourself with the information in this section of

the manual.

- Recommends connecting the camera to a network that use a DHCP (Dynamic Host Configuration

Protocol) server to address devices.

- To ensure secure access to the IP camera, place the camera behind a firewall when it is

connected to a network.

NOTES

- Use megapixel lens for higher image quality.

- The NXC Series are designed and tested to deliver optimal image quality using megapixel lens.

- If the standard definition lens was installed on megapixel camera, the image quality will be poor

than expected.

- Recommend to install the megapixel lens from the following lens manufactures.

-- TAMRON

-- COMPUTAR

-- FUJINON

Starting Installation

1. Install the Lens

- Be careful the lens does not touch camera sensor when installer try to enter the lens into camera.

- Install manual lens or DC auto iris lens.

- If DC auto iris lens needs to install, connect DC auto iris 4-pin connector into iris drive connector

located on the side of the camera.

2. Mount the camera

The camera can be mounted from both top side and bottom side.

3. Connect other peripheral devices

Connect the other peripheral devices such as Alarm, Audio and BNC connector.

4. Supply the camera with power.

- If PoE is not available, connect DC12V or AC24V wires to the camera power connector. Be careful

when DC12V wiring especially the direction of positive and negative. Use power supply compatible

with FCC Class2.

16

- This camera complies with IEEE802.3af standard. It means that the power for this camera can be

supplied from Ethernet cabling without additional power supply. This can be reducing the

installation efforts.

- The camera will complete a configuration processing within approximately 40 seconds. The amber

LED flashes one time per second after the configuration processing are complete.

5. View the camera image

View the camera image using BNC connector or built-in web browser or supplied Client software.

NOTE

This camera will autosense and work with either a straight Ethernet cable or crossover Ethernet

cable.

DC Auto Iris Lens Installation & Adjustment

The camera supports DC-type auto iris lenses. Perform the following steps to install and adjust a

DC-type auto iris lens.

- Solder the lens control wires to the connector supplied with the camera.

Figure 1. 4-Pin iris driver connector

- Attach the DC-type auto iris lens to the lens mount on the front of the camera.

- Plug the connector into the auto iris jack on the side of the camera. The connector is polarized

and can be inserting into the iris jack one way.

Figure 2. DC auto iris Lens connection

17

Audio Connection

This camera supports bidirectional audio. Install the microphone and speaker which has an amplifier

capability.

Figure 3. Audio connection

External Speaker

External Microphone

Alarm Connection

The camera provides two alarm input for external signaling devices and one alarm output for

activating external device. Both Normally Open and Normally Closed devices are supported. Be

consult before alarm device installation how to wire between the camera and alarm devices.

Figure 4. Alarm connector

Alarm Input 1

Alarm Ground

Alarm Input 2

Alarm Output

Alarm Ground

RS485 -

RS485 +

18

OPERATION

-------------------------------------------------------------------------------------------------------------------------------------

Before starting the camera, installation must be complete. The camera completes a configuration

sequence within approximately 40 seconds when power is supplied. The amber LED of this

megapixel camera flash one time per second indicating the configuration sequence is complete.

NOTES

- If the DHCP is enabled but the camera is not connected to a DHCP server, the camera will be set

default IP 192.168.30.220 and try to get IP from DHCP server about every two seconds.

- Network and processor bandwidth limitations might cause the video stream to pause or appear

pixilated when an increased number of Web-interface users connection to the camera. Decrease

the images per second, resolution, compression, or bit rate settings of the Web-interface video

streams to compensate for network or processor limitations.

Minimum conditions for using web browser

The minimum system requirements to use a Web browser with this IP camera are as follows:

- CPU: Pentium® 4 microprocessor, 2.0GHz

- Operational System: Windows XP® or Windows Vista® or Windows7®

- System Memory: RAM 512 Mbyte

- Ethernet: 100 Mbit

- Video Resolution: 1024(Horizontal) x 768(Vertical) pixels or higher

- Internet Explorer® 7 or later

- ActiveX® 1.0.0.13 or later

Accessing the IP camera

1. Open Web browser

- Double click Internet Explorer® icon.

2. Type IP address

- Type the camera’s IP address in the Internet Explorer® address bar.

- The default IP address is

192.168.30.220

NOTES

- If you do not know the camera’s IP address, install the SmartManager® utility software available

on the CD supplied with the product. The utility software will locate the assigned Model name,

Host name, MAC address, IP address, Version and others.

- Refer to the SmartManager® utility software manual for more detail.

3. Log On to the camera

- Click the Live View icon for default live image view or the Setup icon to change the configuration

values.

19

Main Menu

Figure 5. Main menu

The dialog box will be appears.

- Type User ID and Password in the dialog box. The default User ID and Password is

admin

.

NOTE

For security purposes, be sure to change the password after you log on for the first time.

20

LIVE VIEW

-------------------------------------------------------------------------------------------------------------------------------------

The Live View page provides you to select the properties of video source. You can view the live

image from this page and also access the Setup menu and operate the main functions.

Figure 6. Main Live View Page

Page is loading ...

Eneo NXC-1302M Installation Operation User Manual

This manual is also suitable for

Eneo NXC-1302M Installation Operation User Manual

Related papers

Other documents