Color Television
© 2001 TOSHIBA CORPORATION
All Rights Reserved
34HF81
34HF81C
OWNER'S MANUAL
TM
Owner's Record
The model number and serial number are on the back
of your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
Model number:
Serial number:
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
2
Important Information
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
The lightning symbol in the triangle tells you that the
voltage inside this product may be strong enough to
cause an electric shock. DO NOT TRY TO SERVICE
THIS PRODUCT YOURSELF.
The exclamation mark in the triangle tells you that
important operating and maintenance instructions
follow this symbol.
CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS
POLARIZED PLUG WITH AN EXTENSION CORD
RECEPTACLE OR OTHER OUTLET UNLESS THE
PRONGS CAN BE FULLY INSERTED INTO THE
OUTLET TO PREVENT ANY EXPOSURE OF THE
PRONGS ON THE POLARIZED PLUG.
ATTENTION
POUR PRÉVENIR LES CHOCS ÉLECTRIQUES NE PAS
UTILISER CETTE FICHE POLARISÉE AVEC UN
PROLONGATEUR, UNE PRISE DE COURANT OU UNE
AUTRE SORTIE DE COURANT, SAUF SI LES LAMES
PEUVENT ÊTRE INSÉRÉS À FOND SANS EN LAISSER
AUCUNE PARTIE À DÉCOUVERT.
CAUTION
The plug has one prong wider
than the other and will fit
only one way into a standard
electrical outlet (120 volt AC,
60 Hz). If the plug does not
fit into the outlet, try turning
it around. If the plug still does
not fit, the outlet is probably non-standard and must be
replaced by a qualified electrician. Do not tamper with the plug
or try to force it into a non-standard outlet.
Note to CATV system installers in the USA
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC, which provides
guidelines for proper grounding, and, in particular, specifies that
the cable ground shall be connected to the grounding system of
the building, as close to the point of cable entry as practical.
Precautions
Installing your TV
• Place the TV on the floor or on a sturdy platform. The
mounting surface should be flat and steady. If you install the
TV on a soft floor, make sure that the floor is not damaged
by the weight of the TV.
• Place the TV far enough away from the walls to allow proper
ventilation. This will prevent the TV from overheating and
avoid possible damage to the TV. Avoid dusty places too.
Using your TV
• Do not stand or climb on the TV.
• Do not put any heavy object on top of the TV.
• Do not place containers with liquids such as drinks or
cosmetics on the TV. If any foreign material or water leaks
into the TV, unplug the AC cord and contact your dealer.
• Avoid displaying stationary images on your TV screen for
extended periods of time. Stationary patterns generated by a
POP/double-window display, computer displays, video
games, stock market reports, etc., can become permanently
engrained on the picture tube. This damage is not protected
by your warranty because it is the result of misuse. If you wish
to use your TV to display still images, reduce brightness and
contrast settings. Never leave a POP/double-window,
computer, or video game display unattended.
Cleaning your TV
• To clean the TV screen:
1. First remove the plug from the power outlet to avoid
possible shock hazard.
2. Use a clean cellulose sponge or chamois cloth dampened
with a solution of mild detergent and warm water to clean
TV screen and trim. Do not use too much water on the TV
screen. Water spills into the cabinet and may cause damage
to the TV. Avoid excess water.
3. Remove any extra moisture with the same cloth or a dry
one.
• To maintain the finish and appearance of the cabinet, polish
it from time to time with a quality furniture polish.
CAUTION
Never use strong solvents such as thinner, benzene or other
chemicals on or near cabinet, as they might damage the finish of
the cabinet.
Wide prong
3
Introduction................................................................ 4
Welcome to Toshiba ......................................................... 4
Exploring your new TV ................................................... 4
Connecting your TV .................................................. 5
Connecting a VCR .......................................................... 5
Connecting a cable converter box .................................... 6
Connecting a cable converter box and VCR ..................... 6
Connecting a DVD player or satellite receiver and
a VCR.............................................................................. 7
Connecting a DVD player (with or without
ColorStream™) and a VCR ............................................ 8
Connecting a DTV receiver/set-top box (with or without
ColorStream™) and a VCR ............................................ 9
Connecting two VCRs ................................................... 10
Connecting a camcorder ................................................ 10
Connecting an audio system .......................................... 11
Connecting an A/V receiver ........................................... 11
Using the remote control ...................................... 12
Preparing the remote control for use .............................. 12
Installing the remote control batteries ............................ 12
Remote Control functional key chart ...................... 13
Programming the remote control for use with
your audio/video devices ................................................ 15
Device code setup ................................................... 15
Searching and sampling the code of a device (991) .... 15
Verifying the device code (990) ............................... 16
Using the volume lock feature (993) ....................... 16
Operational feature reset (980) ............................... 16
Device code table ...............................................17-20
Learning about the remote control .......................... 21
Setting up your TV .................................................. 22
Learning about the menu system ................................... 22
Changing the on-screen display language ....................... 23
Selecting the antenna input............................................ 23
Adding channels to the TV’s memory ............................ 24
Programming channels automatically ...................... 24
Adding and erasing channels manually.................... 24
Adjusting the tilt correction feature......................... 25
Changing channels ........................................................ 25
Using the TV’s features.......................................... 26
Adjusting the channel settings........................................ 26
Switching between two channels ............................. 26
Programming your favorite channels ....................... 26
Labeling channels ................................................... 27
Viewing the wide-screen picture formats ........................ 29
Selecting the picture size ......................................... 29
Scrolling the Theater Wide picture
(Theater Wide 2 and 3 only) .................................. 31
Using the POP double-window feature .......................... 32
Switching the main and POP pictures ..................... 33
Freezing the POP picture ........................................ 33
Using the favorite channel search function .............. 33
Using the LOCKS menu ............................................... 34
Entering the PIN code ............................................ 34
Using the V-CHIP menu ............................................... 35
ENABLE BLOCKING .......................................... 35
TV RATING (Independent rating system for
broadcasters) ........................................................... 35
MPAA RATING (Independent rating system for
movies) ................................................................... 36
BLOCKING OPTION .......................................... 36
Unlocking programs temporarily ............................ 37
Locking channels ........................................................... 37
Locking video inputs ..................................................... 38
Using the front panel lock feature .................................. 39
Changing the PIN code ................................................. 39
Adjusting the picture ..................................................... 40
Selecting the picture mode ...................................... 40
Adjusting the picture quality ................................... 40
Saving new preference............................................. 41
Using the flesh tone feature ..................................... 41
Using the Digital Noise Reduction (DNR) feature .... 41
Selecting the cinema mode...................................... 42
Selecting the color temperature ............................... 42
Resetting picture adjustments ................................. 42
Selecting the video input source ..................................... 43
Labeling the video input sources .................................... 43
Using the closed caption feature ..................................... 44
Setting the sleep timer.................................................... 45
Setting the clock ............................................................ 45
Adjusting the sound ....................................................... 46
Muting the sound ................................................... 46
Selecting stereo/SAP broadcasts .............................. 46
Using the WOW surround sound feature ................ 47
Adjusting the sound quality .................................... 47
Resetting audio adjustments ................................... 48
Using the sub-woofer system “CYCLONE™” ....... 48
Turning off the built-in speakers ............................. 49
Selecting the Audio OUT sound ............................. 49
Using the StableSound™ feature ............................ 50
Selecting the background of the menu display ............... 50
Displaying on-screen information .................................. 50
Viewing the demonstration mode .................................. 51
Understanding the auto power off feature ...................... 51
Understanding the last mode memory feature ................ 51
Appendix ................................................................... 52
Specifications ................................................................. 52
Troubleshooting ............................................................. 53
Limited United States Warranty ..................................... 54
Index .......................................................................... 55
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
4
Introduction
Welcome to Toshiba
Congratulations! You have purchased one of the finest TVs on the
market. The goal of this manual is to guide you through setting up
and operating your Toshiba TV as quickly as possible.
This manual applies to models 34HF81 and 34HF81C. Before you
start reading, check your model number on the back of the TV.
Instructions in this manual are based on using the remote control.
You can also use the controls on the TV if they have the same name as
those on the remote control.
Please read all the safety and operating instructions carefully, and keep
the manual for future reference.
Exploring your new TV
You can operate your TV using the buttons on the front panel or the
remote control. The back panel and front panel (behind the door)
provide all the terminal connections you will need to connect other
equipment to your TV. See “Connecting your TV” on page 5.
CHANNELVOLUMEMENU
TV/VIDEO
R
L/MONO
AUDIOVIDEOS-VIDEO
POWER
VIDEO-3 IN
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
P
R
L
Y
P
B
P
R
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
Front
Video/audio inputs
(Video 3)
Volume x •
TV/VIDEO
POWER
Power
indicator
Remote sensor
Channel zy
MENU
Menu
x •zy
Behind the door
Please Note
On some models, the SET UP
menu automatically appears on-
screen the first time the TV is
turned on.
To change the menu settings, see
“Setting Up Your TV” on page 22
for details.
To close the menu, either press
EXIT or turn the TV off.
Back
ANT OUT
ANT-1 IN ANT-2 IN
Audio Center
Channel IN
Variable Audio
OUT
Video/Audio
OUT
ColorStream
HD1
ColorStream
HD2
VIDEO 1/2
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
5
Connecting your TV
If you have not connected electronic equipment before, or you have
been frustrated in the past, you may wish to read this section. (Cables
are not supplied.)
• A coaxial cable is the standard cable that comes in from your
antenna or cable converter box. Coaxial cables use “F”
connectors.
• Audio and video cables are usually color-coded according to use:
yellow for video and red and white for audio. The red audio cable
is for the stereo right channel, and the white audio cable is for
the stereo (or mono) left channel. If you look at the rear panel of
the TV, you will see that the terminals are color-coded in the
same manner as the cables.
• S-video cables provide better picture performance. S-video cables
can only be used with S-video compatible components.
• ColorStream™ cables come in sets of three and provide the best
picture performance. ColorStream cables can only be used with
ColorStream compatible components.
Connecting a VCR
This connection allows you to watch local channels and video
programs, play or record on the VCR while watching TV, and record
from one channel while watching another channel.
You will need:
• one coaxial cable
• one pair of audio cables (one single audio cable for a mono VCR)
• one video cable (one S-video cable for an S-VHS VCR)
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
PR
L
Y
P
B
PR
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
IN from ANT
VIDEO AUDIO
OUT to TV
CH 3
LR
CH 4
IN
OUT
Caution:
Do not plug the TV in until you have finished
connecting all of your equipment.
Note:
If you have a mono VCR, connect L/Mono to
VCR Audio OUT using only one audio cable.
If you have an S-VHS VCR, use an S-video
cable (in the S-video jacks) instead of the
regular video cable.
Do not connect a regular video cable and an
S-video cable to Video-1 at the same time.
ANTENNA
Coaxial Cable
AUDIO
Cables
VIDEO
Cable
S-VIDEO
Cable
Color Stream
Cable
Cable lead-in from Cable Box or Antenna
Stereo VCR
TV
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
6
Connecting a cable converter box
This connection allows you to watch basic and premium cable
channels.
To use the TV’s features, select ANT-1. To view premium channels,
select ANT-2, tune the TV to channel 3 or 4 (whichever channel is
vacant in your area), and use the converter box to change channels.
You will need:
• two coaxial cables
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
P
R
L
Y
P
B
P
R
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
Cable converter box
IN OUT
Connecting a cable converter box and VCR
This connection allows you to watch and record basic and premium
cable channels, watch videotapes, and record one channel while
watching another channel. To use the TV’s features, select ANT-1.
To view premium channels or record with the VCR, select ANT-2,
tune the TV to channel 3 or 4 (whichever channel is vacant in your
area), and use the converter box to change channels.
You will need:
• three coaxial cables
• one pair of audio cables (one single audio cable for a mono VCR)
• one video cable (one S-video cable for an S-VHS VCR)
IN from ANT
OUT to TV
CH 3
CH 4
VIDEO
AUDIO
LR
IN
OUT
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
P
R
L
Y
P
B
P
R
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
Cable converter box
IN OUT
Note:
When you use a converter box with your TV,
the remote control will not operate some
features,such as programming your favorite
channels, labeling channels, and locking
channels.
Note:
If you have a mono VCR, connect L/Mono to
VCR Audio OUT using only one audio cable.
If you have an S-VHS VCR, use an S-video
cable (in the S-video jacks) instead of a
regular video cable. Do not connect a regular
video cable and an S-video cable to Video-1
(or Video-2) at the same time.
When you use a converter box with your TV,
the remote control will not operate some
features, such as programming your favorite
channels, labeling channels, and locking
channels.
TV
From Cable
TV
From Cable
Stereo VCR
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
7
Connecting a DVD player or satellite receiver
and a VCR
This connection allows you to watch DVD/satellite, VCR, and TV
programs, and record one TV channel while watching another
channel.
You will need:
• one coaxial cable
• two pairs of audio cables (one single and one pair of audio cables
for a mono VCR)
• one video cable (between the TV and VCR)
• one S-video cable (between the TV and DVD player/satellite
receiver)
IN from ANT
VIDEO AUDIO
OUT to TV
CH 3
LR
CH 4
IN
OUT
IN from ANT
VIDEO
OUTOUT
S-VIDEO
AUDIO
OUT
L
R
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
P
R
L
Y
P
B
P
R
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
Caution:
The unauthorized recording of television
programs, videotapes, and other materials
may infringe upon the provisions of copyright
laws.
Note:
For the highest possible picture quality from a
non-ColorStream DVD player/satellite
receiver, you must use an S-video cable
between the TV and DVD player/satellite
receiver. (If your DVD player or satellite
receiver is ColorStream-compatible, see page
8).
Do not connect both an S-video cable and a
regular video cable between the TV and DVD
player/satellite receiver at the same time.
Doing so will distort the picture.
Do not connect the DVD player/satellite
receiver and VCR to the same video channel
on the TV. (See the illustrations, which show
the DVD player/satellite receiver connected to
Video-1 on the TV and the VCR connected to
Video-2 on the TV.)
TV
From Antenna
Stereo VCR
From Satellite Dish
DVD/Satellite receiver
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
8
Connecting a DVD player (with or without
ColorStream™) and a VCR
This connection allows you to watch DVD, VCR, and TV programs,
and record DVD and TV programs. You can record from one source
while watching a program from another source.
Your TV has ColorStream component video inputs. Connecting your
TV to a ColorStream-compatible DVD player (such as a Toshiba
ColorStream-equipped DVD player) can greatly enhance picture
quality and realism.
You will need:
• one coaxial cable
• three pairs of audio cables (two single and one pair of audio cables
for a mono VCR)
• two video cables
• one set of ColorStream video cables (one S-video cable for a non-
ColorStream DVD player;see notes at right)
IN from ANT
OUT to TV
CH 3
CH 4
VIDEO AUDIO
LR
IN
OUT
Satelite IN
VIDEO
OUT
S-VIDEO
AUDIO
COMPONENT VIDEO
OUT
L
R
L
R
P
R
P
B
Y
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
P
R
L
Y
P
B
P
R
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
Stereo VCR
From Antenna
TV
DVD Player with ColorStream™
Caution:
The unauthorized recording of television
programs, videotapes, and other materials
may infringe upon the provisions of copyright
laws.
Note:
For the highest possible picture quality, you
must use ColorStream video cables between
the TV and DVD player. You can connect the
ColorStream cables from the DVD player to
either ColorStream jack on the TV (HD1 or
HD2).
The ColorStream HD1 and HD2 jacks can be
used with Progressive (480p) and Interlace
(480i,1080i) scan systems.
If your DVD player is not ColorStream-
compatible, use the S-video connections
(both audio and video) instead of the
ColorStream connections. Do not connect
both S-Video and ColorStream cables
between the TV and DVD player at the same
time.
To record from the DVD player, set the VCR
to Line IN. To monitor recording from the
DVD player, set the VCR to Line IN, and set
the TV to Video-1.
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
9
Connecting a DTV receiver/set-top box (with
or without ColorStream™) and a VCR
This connection allows you to watch DTV (digital TV broadcast),
VCR, and TV programs, and record DTV and TV programs. You can
record from one source while watching a program from another
source.
Your TV has ColorStream component video inputs. Connecting your
TV to a ColorStream-compatible DTV receiver can greatly enhance
picture quality and realism.
You will need:
• one coaxial cable
• three pairs of audio cables (two single and one pair of audio
cables for a mono VCR)
• two video cables
• one set of ColorStream video cables (one S-video cable for a non-
ColorStream DTV receiver; see notes at right)
VIDEO
OUT
S-VIDEO
AUDIO
COMPONENT VIDEO
OUT
L
R
L
R
PRPBY
Satelite IN
IN from ANT
OUT to TV
CH 3
CH 4
VIDEO AUDIO
LR
IN
OUT
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
P
R
L
Y
P
B
P
R
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
DTV Receiver
VCR
From
Antenna
From
DTV Antenna
TV
Note:
For the highest possible picture quality, you
must use ColorStream video cables between
the TV and DTV receiver. You can connect the
ColorStream cables from the DTV receiver to
either ColorStream jack on the TV (HD1 or
HD2).
The ColorStream HD1 and HD2 jacks can be
used with Progressive (480p) and Interlace
(480i,1080i) scan systems.
If your DTV receiver is not ColorStream-
compatible, use the S-video connections
(both audio and video) instead of the
ColorStream connections. Do not connect
both S-Video and ColorStream cables
between the TV and DTV receiver at the same
time.
To record from the DTV receiver, set the VCR
to Line IN. To monitor recording from the DTV
receiver, set the VCR to Line IN, and set the
TV to Video-1.
Caution:
The unauthorized recording of television
programs, videotapes, and other materials
may infringe upon the provisions of copyright
laws.
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
10
Connecting two VCRs
This connection allows you to record (dub/edit) from one VCR to
another VCR while watching a videotape. You can also record from
one TV channel while watching another TV channel.
You will need:
• one coaxial cable
• two pairs of audio cables (two single audio cables for mono
VCRs)
• two video cables (two S-video cables for S-VHS VCRs)
VIDEO AUDIO
CH 3
LR
CH 4
IN
OUT
IN from ANT
OUT to TV
CH 3
CH 4
VIDEO AUDIO
LR
IN
OUT
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
PR
L
Y
P
B
PR
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
Connecting a camcorder
This connection allows you to watch video materials recorded on a
camcorder.
You will need:
• one pair of audio cables
• one video cable (one S-video cable for an S-VHS camcorder)
VIDEO
AUDIO
OUT
L
R
CHANNELVOLUMEMENU
TV/VIDEO
R
L/MONO
AUDIOVIDEOS-VIDEO
POWER
VIDEO-3 IN
VCR1
From Antenna
TV
***
Caution:
The unauthorized recording of television
programs, videotapes, and other materials
may infringe upon the provisions of copyright
laws.
Note:
If you have S-VHS VCRs, use S-video cables
instead of regular video cables. Do not
connect both a regular video cable and an S-
video cable to Video-1 or Video-2 at the same
time.
Do not connect the same VCR to the output
and input jacks on the TV at the same time.
To dub or edit, VCR 2 must select Line IN,
and the TV must select Video-1.
*
The Video OUT jack does not output the
POP picture.
**
The Audio OUT jacks can output the sound
of either the Main or POP picture (see
“Selecting the Audio OUT sound” on page
49).
Camcorder
TV front panel
VCR2
Caution:
If you have an S-VHS camcorder, use an S-
video cable between the S-video jacks on the
camcorder and TV. Do not connect both a
regular video cable and an S-video cable at
the same time.
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
11
LINE IN
LR
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
P
R
L
Y
P
B
P
R
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
Connecting an audio system
This connection allows you to use an audio amplifier to adjust the
audio level. This also allows you to use external speakers.
To control the audio, turn on the TV and the stereo amplifier, and
turn off the built-in speakers (see “Turning off the built-in speakers”
on page 49).
You will need:
• one pair of audio cables
Note:
To hear sound when using an external audio amplifier, the
volume of both the TV and the amplifier must be set
above 0 (zero).
For example, if the volume of the TV is set to 0, you will
not be able to hear any sound, even the volume of the
amplifier is at its highest level.
Connecting an A/V receiver
This connection allows you to use an audio/video (A/V) receiver to
enhance your TV’s sound.
If you have a system with Dolby Pro Logic
®
surround sound, you can
add to the realism of the sound by using the TV’s internal speakers as
center channel speakers.
You will need:
• one pair of audio cables
• one single audio cable for the audio center channel
• one video cable
ANT-1 OUT ANT-2
ANT(75 )
S-VIDEO
VIDEO
L/
MONO
AUDIO
R
VIDEO-2VIDEO-1
Y
P
B
P
R
L
Y
P
B
P
R
AUDIO
COLOR
STREAM
HD - 2
COLOR
STREAM
HD - 1
R
L
AUDIO
R
OUT
AUDIO CENTER
CHANNEL IN
L/
MONO
AUDIO
ON OFF
VIDEO
VAR
AUDIO
L
R
R
IN
IN
ON OFF
Note:
Refer to the instructions provided with your A/V receiver
for details about your surround sound system.
When the Audio Center Channel ON/OFF switch is in
the ON position, the TV speakers will function only as
center channel speakers.
Adjust the volume for the center channel speakers
using the center level control on the A/V receiver.
To use the TV speakers as normal speakers, set the
Audio Center Channel ON/OFF switch to the OFF
position.
TV
TV
Caution:
To avoid damaging the speakers, turn the TV
off before connecting or disconnecting the
Audio Center Channel audio cable.
Amplifier
To A/V Receiver
Video
OUT
TV
IN
Center
OUT
From Antenna
Dolby Pro Logic* surround sound
system connection example
Right
speaker
Left
speaker
Surround
speaker L
Surround
speaker R
VCR
A/V receiver
Audio Video
Video
Audio
Video
Audio
center
channel
Audio
LDP/DVD
T V
_________
* Dolby Pro Logic is a registered trademark
of Dolby Laboratories Licensing
Corporation.
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
12
Using the remote control
Preparing the remote control for use
Your Toshiba TV remote control has one dedicated TV mode and five
universal modes: VCR, Cable/SAT, DVD, Audio1, and Audio2. The
target devices and default devices being programmed for each mode
are as follows:
Target device/Mode mapping
Mode Device
TV Toshiba TV
CABLE/SAT Universal Cable, Satellite
VCR Universal VCR, DVD, LD, Cassette
DVD Universal DVD, VCR, LD, Cassette
AUDIO1 Universal Audio: Amp., Tuner, Misc.Audio, CD/MD
AUDIO2 Universal Audio: CD/MD, Amp., Tuner, Misc.Audio
Default device codes
Mode Default device
TV Toshiba TV
CABLE/SAT Toshiba Satellite receiver
VCR Toshiba VCR
DVD Toshiba DVD
AUDIO1 Pioneer Audio receiver
AUDIO2 Pioneer LD
Repeatedly press MODE to cycle among the modes.If you own
different brands of audio/video devices,you must first program your
remote control (see “Programming the remote control for use with
your audio/video devices” on page 15).
Installing the remote control batteries
To install the batteries:
1. Slide the battery cover off the back of the remote control.
2. Install two “AA” size alkaline batteries. Match the + and – signs
on the batteries to the signs on the battery compartment.
3. Slide the battery cover back on to the remote control until the
lock snaps.
Note:
Your TV’s remote control may not operate
certain features on your VCR, cable TV
converter, or other electronic device.
Refer to the owner’s manuals for your other
devices to determine their available features.
If your TV’s remote control does not operate a
specific feature on a device,use the remote
control that came with the device.
Caution:
• Dispose of batteries in a designated
disposal area.Do not throw batteries into a
fire.
• Do not mix battery types or combine used
batteries with new ones.
• If the batteries are dead or if you will not
use the remote control for a long time,
remove the batteries to prevent battery acid
from leaking into the battery compartment.
Note:
• Battery life expectancy is about one year
with normal use.
MODE
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
13
Remote Control functional key chart
Key Label
Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD Cassete
(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR)
LIGHT Lights the remote key, and toggles between enabled and disabled Illumination mode.
SLEEP Sleep timer --- --- --- --- --- --- ---
POWER Power Power Power Power Power Power Power Power
1/MOVIE Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 AV input 1 Digit 1 Digit 1
2/SPORTS Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 AV input 2 Digit 2 Digit 2
3/NEWS Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 AV input 3 Digit 3 Digit 3
4/SERVICES Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 AV input 4 Digit 4 Digit 4
5/LIST Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 CD Digit 5 Digit 5
6 Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Tuner Digit 6 Digit 6
MODE Remote control device mode selection
PIC SIZE Selects the This button is not available for other devices connected to this TV.
picture size.
7 Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Phono Digit 7 Digit 7
8 Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Cassette Digit 8 Digit 8
9 Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Aux Digit 9 Digit 9
ACTION --- Menu
Action, Menu
Menu Menu --- --- ---
100/– 100 100 100 100 100 100 100 100
0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0
ENT --- CH Enter CH Enter CH Enter --- --- --- ---
GUIDE/SETUP
--- Guide Guide Program DVD setup Program Program ---
INFO/TITLE --- --- INFO --- TITLE= --- --- ---
Top menu
FAVORITE/ Favorite CH ---
Favorite CH
--- Subtitle --- --- ---
SUBTITLE
ALPHASORT/ --- --- Alphasort --- Audio --- --- ---
AUDIO
MENU/ Menu open/ Select Select Enter Enter --- --- ---
ENTER Enter
yz Menu select Menu select Menu select Menu select Menu select --- --- ---
x •/(FAV) x • Menu select/ Menu select Menu select Menu select Menu select --- --- ---
(FAV) x •
VOL yz Volume Volume Volume Volume Volume Volume Volume ---
up/down* up/down* up/down* up/down* up/down* up/down* up/down*
EXIT/ Exit Exit Exit Exit DVD clear Exit/Clear Exit/Clear Exit/Clear
DVD CLEAR
CH
yz Channel Channel Channel Channel --- Channel --- ---
up/down up/down up/down up/down up/down
INPUT TV/Video TV TV VCR input TV Input TV TV
select
MUTE
Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute*
---
RECALL On-screen On-screen On-screen On-screen On-screen --- --- ---
display display display display display
CH RTN/ Previous Previous Previous Previous DVD --- --- ---
DVD RTN channel channel channel channel return
SLOW/
•
--- --- --- Forward Forward --- --- ---
DIR
x
--- --- --- --- Reverse --- --- ---
SKIP/
•
--- --- --- --- Forward CH forward Forward Forward
SEARCH
x
--- --- --- --- Reverse CH reverse Reverse Reverse
REW VCR VCR VCR Rewind Rewind Rewind Rewind Rewind
PAUSE/STEP VCR VCR VCR Pause Pause Pause Pause Pause
PLAY VCR VCR VCR Play Play Play Play Play
FF VCR VCR VCR F. Forward F. Forward F. Forward F. Forward F. Forward
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
14
Key Label
Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD Cassete
(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR)
TV/VCR VCR Bypass A/B TV/SAT TV/VCR --- --- --- ---
AM/FM DISC --- --- --- --- Disc shift AM/FM Disc shift Deck side
A/B switch
STOP VCR VCR VCR Stop Stop Stop Stop Stop
REC VCR VCR VCR Record --- Record Record Record
PIP CH
yz
POP channel TV TV TV TV TV TV TV
up/down
PIP POP on/off TV TV TV TV TV TV TV
MULTI
This button is not available for this TV model or any other device connected to this TV.
STILL POP Still TV TV TV TV TV TV TV
SWAP POP Swap TV TV TV TV TV TV TV
LOCATE This button is not available for this TV model or any other device connected to this TV.
SOURCE POP Source TV TV TV TV TV TV TV
Notes:
•“---” will send nothing.
•“ TV” will jump to TV.
•“ VCR” will jump to last active VCR or DVD. Active VCR/DVD is defined as the mode that remains for a minimum of 5
seconds, or if a key is pressed in that mode.
*
The VOLUME and MUTE will jump to “TV” by default. When the volume is unlocked, all the devices will have their own volume.
The AUDIO1/2 (Receiver, CD) modes will have their own volume even if Volume Lock is on TV, CABLE/SAT, VCR, or DVD. See
“Using the Volume Lock feature” on page 16.
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
15
Programming the remote control for use with
your audio/video devices
Device code setup
1. Refer to the Device code table on pages 17 – 20 to find the code
for the brand of your device.
If more than one number is listed, try each one separately until
you find the one that works.
2. Press MODE until the Mode indicator of the device (CABLE/
SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.
3. While holding down the RECALL button, press the Channel
Number buttons to enter the four-digit code of your brand of
device. If a valid code is entered, the mode indicator will blink
twice. If an invalid code is entered, the mode indicator will blink
one long blink.
4. Point the remote control at the device and press POWER to test
the code.
If the device turns on, you have entered the correct code.
If the device does not respond to the remote control, you may
have entered the wrong code. Repeat steps 3 and 4 using another
code.
5. Press MODE to select the TV mode to control the TV.
Searching and sampling the code of a device (991)
If you do not know the device code for a particular target unit, you
can cycle the remote control through the available codes for that
device mode and sample the functions to find the code that properly
operates the target device. The keys available to be sampled, provided
they are applicable to that mode, are 0, 1, 2, 3, POWER, VOL y,
CH y, PLAY, and STOP. Invalid keys will be ignored while in
program mode.
To cycle through each available device code and sample its functions:
1. Press MODE to select the mode you want to set up.
2. While holding down the RECALL button, press 9 –9 –1.
The remote control will enter program mode.
3. Point the remote control at the target device and press POWER
(or other function buttons that are available to be sampled).
4. If the device responds to the remote control:
Press RECALL to store the device code.
The mode indicator will blink twice and the remote control
will exit the program mode.
If the device does not respond to the remote control:
Press y, and then press POWER.
Repeat this step until the device responds to the remote
control, and then press RECALL.
Note: When a search cycle is completed, the mode indicator will blink three
times. The remote control will begin to cycle through the available codes
again. If no key is pressed within 10 seconds while programming, the
remote control will exit the program mode and return to the previous
code.
POWER
Numbers
RECALL
Note:
• Every time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes.These VCRs
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and
does not respond to any of the codes for
your VCR brand, set the switch to the other
position (VCR1 or VCR2) and reprogram
the remote control
MODE
y
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
16
Verifying the device code (990)
Use this feature to verify the codes for your other devices. The
number of blinks after pressing the 1, 2, 3, and 4 buttons is the 4-
digit code set up for that mode.
For example, to verify the device code of the VCR:
1. Press MODE to select the VCR mode.
2. While holding down the RECALL button, press 9 –9 –0.
3. Press 1 ➝ 0 blinks.
4. Press 2 ➝ 3 blinks.
5. Press 3 ➝ 8 blinks.
6. Press 4 ➝ 5 blinks.
This verifies that the device code of the VCR mode is “0385.”
Using the volume lock feature (993)
For the TV, CABLE/SAT, VCR, and DVD modes, the volume
controls (VOL yz and MUTE) can be programmed (locked) to the
selected device mode. This feature does not apply to the AUDIO1/2
modes.
For example, to lock the volume controls to always jump to the
CABLE/SAT mode:
1. Repeatedly press MODE to select the CABLE/SAT mode.
2. While holding down the RECALL button, press 9 –9 –3.
3. Press VOL y.
The Mode indicator will blink two times (locked).
The following table describes in more detail the Volume Lock
implementation.
Volume
TV CBL/SAT VCR DVD AUD1 AUD2
Locked to
TV (default)
TV TV TV TV AUD1 AUD2
CBL/SAT CBL/SAT CBL/SAT CBL/SAT CBL/SAT AUD1 AUD2
VCR VCR VCR VCR VCR AUD1 AUD2
DVD DVD DVD DVD DVD AUD1 AUD2
AUD1 AUD1 AUD1 AUD1 AUD1 AUD1 AUD1
AUD2 AUD2 AUD2 AUD2 AUD2 AUD2 AUD2
To reset the volume controls to the original device code:
1. While holding down the RECALL button, press 9 –9 –3.
2. Press VOL z.
The Mode indicator will blink four times (unlocked).
Operational feature reset (980)
This feature clears all setup features not related to “Device code set
up” and resets the Volume Lock to “TV.”
To reset the features:
While holding down the RECALL button, press 9 –8 –0.
The Mode indicator will blink two times, and then pause and
blink two more times.
Number
MODE
RECALL
VOL y z
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
17
Cable box setup codes
Brand Code
ABC 0020, 0022, 0026,
0027, 0030, 0032,
0033, 0036
Allegro 0172, 0334
Americast 0918
Antronix 0041, 0226
Archer 0041, 0172, 0226,
0816
BBT 0286
Belcor 0075
Bell & Howell 0033
Bell South 0918
Cable Star 0075
Cabletenna 0041
Cableview 0041
Century 0172
Citizen 0172, 0334
Colour Voice 0044, 0050
Comtronics 0059
Contec 0038
Digi 0656
Eastern 0021
Emerson 0816
Everquest 0034, 0059
Focus 0419
GC Electronics 0075, 0226
Garrard 0172
Gemini 0034, 0089, 0816
General Instrument 0030, 0295, 0495,
0829
GoldStar 0059, 0163
Goodmind 0816
Hamlin 0028, 0039, 0053,
0278, 0292
Hitachi 0030
Hytex 0026
Jasco 0034, 0172, 0334
Jerrold 0022, 0030, 0031,
0033, 0034, 0043,
0295, 0495, 0829
Linsay 0459
Magnavox 0046
Memorex 0019
Movie Time 0082, 0175
NSC 0082, 0089, 0175
Novaplex 0637
Oak 0026, 0038
Optimus 0040
Panasonic 0019, 0040, 0126
Panther 0656
Paragon 0019
Philips 0044, 0046, 0050,
0172
Pioneer 0042, 0163, 0552,
0896
Popular Mechanics 0419
Prelude 0789
Pulsar 0019
Quasar 0019
RCA 0040
Radio Shack 0034, 0334, 0816,
0902
Realistic 0226
Recoton 0419
Regal 0039, 0278, 0292
Regency 0021
Rembrandt 0030, 0089
Runco 0019
SL Marx 0059
Samsung 0059, 0163
Scientific Atlanta 0027, 0036, 0496,
0896
Seam 0529
Signal 0034, 0059
Signature 0030
Sprucer 0040
StarSight 0441, 0561
Starcom 0022, 0034
Stargate 0034, 0059, 0789,
0816
Starquest 0034
Sylvania 0020
TFC 0329
TV86 0082
Tandy 0277
TeleCaption 0240
Teleview 0059
Texscan 0020
Timeless 0437
Tocom 0031, 0032
Toshiba 0019
Tusa 0034
Unika 0041, 0172, 0226
United Artists 0026
Universal 0041, 0075, 0172,
0210, 0226
Viewstar 0046, 0082, 0277
Zenith 0019, 0073, 0544,
0918
Zentek 0419
Satellite Receiver setup codes
Brand Code
AlphaStar 0791
Chaparral 0072, 0235
Curtis Mathes 0080
Echostar 0288, 0299, 0794,
1024
Expressvu 0794
General Instrument 0380, 0646, 0888
HTS 0794
Hitachi 0838
Homecable 0257
Hughes Network
Systems 0768
IQ 0229
IQ Prism 0229
JVC 0794
Jerrold 0380, 0646
Legend 0288
Macom 0080
Magnavox 0741, 0743
Memorex 0288, 0743
Next Level 0888
Panasonic 0720
Philips 0741, 0743
Primestar 0380, 0646
RCA 0162, 0411, 0585,
0874
Radio Shack 0888
Realistic 0071
STS 0229
Sony 0658
Star Choice 0888
Toshiba 0080, 0101, 0768,
0809, 1071, 1072,
1073
Uniden 0071, 0093, 0257,
0741, 0743
Zenith 0080, 0875
Device code table
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
18
VCR setup codes
Brand Code
Admiral 0067, 0228
Adventura 0019
Aiko 0297
Aiwa 0019, 0056, 0326
Akai 0060, 0072, 0080,
0125
America Action 0297
American High 0054
Asha 0259
Audiovox 0056
Beaumark 0259
Bell & Howell 0123
Broksonic 0021, 0140, 0203,
0228, 0314, 0380,
0498
CCE 0091, 0297
Calix 0056
Canon 0054
Capehart 0039
Carver 0100
Cineral 0297
Citizen 0056, 0297
Colt 0091
Craig 0056, 0066, 0091,
0259, 0290
Curtis Mathes 0054, 0060, 0079,
0181
Cybernex 0070, 0259
Daewoo 0039, 0064, 0297,
0580
Daytron 0039
Denon 0061
Dynatech 0019
Electrohome 0056
Electrophonic 0056
Emerex 0051
Emerson 0019, 0021, 0055,
0056, 0062, 0080,
0087, 0107, 0140,
0203, 0227, 0228,
0231, 0297, 0313,
0314, 0380, 0498,
0580
Fisher 0066, 0073, 0085,
0123
Fuji 0052, 0054
Funai 0019
GE 0054, 0067, 0079,
0221, 0259
Garrard 0019
Go Video 0451, 0545, 0662
GoldStar 0056, 0057
Gradiente 0019, 0027
HI-Q 0066
Harley Davidson 0019
Harman/Kardon 0057, 0100
Harwood 0087, 0091
Headquarter 0065
Hitachi 0019, 0060, 0061,
0124
Hughes Network
Systems 0061
JVC 0027, 0060, 0086,
0403
Jensen 0060
KEC 0056, 0297
KLH 0091
Kenwood 0057, 0060, 0086,
0403
Kodak 0054, 0056
LXI 0056
Lloyd's 0019, 0227
Logik 0091
MEI 0054
MGA 0062, 0080, 0259
MGN Technology 0259
MTC 0019, 0259
Magnasonic 0297
Magnavox 0019, 0054, 0058,
0100, 0129, 0168
Magnin 0259
Marantz 0054, 0100
Marta 0056
Matsushita 0054, 0181, 0473
Memorex 0019, 0054, 0056,
0058, 0065, 0066,
0067, 0123, 0181,
0228, 0259, 0326,
0473, 1056, 1181,
1281
Minolta 0061, 0124
Mitsubishi 0062, 0067, 0080,
0086
Motorola 0054, 0067
Multitech 0019, 0091
NAD 0077
NEC 0057, 0059, 0060,
0086, 0123
Nikko 0056
Nikon 0053, 0272
Noblex 0259
Olympus 0054
Optimus 0056, 0067, 0077,
0123, 0181, 0451,
0473, 1067, 1081,
1181, 1281
Optonica 0081
Orion 0021, 0203, 0228,
0314, 0498
Panasonic 0054, 0096, 0181,
0244, 0473, 0635,
1081, 1181, 1281
Penney 0054, 0056, 0057,
0059, 0061, 0073,
0259
Pentax 0061, 0124
Philco 0054, 0228, 0498
Philips 0054, 0081, 0100,
0129, 0637, 1100,
1200
Pilot 0056
Pioneer 0077, 0086
Portland 0039
Profitronic 0259
Proscan 0079, 0221
Protec 0091
Pulsar 0058, 0070
Quarter 0065
Quartz 0065
Quasar 0054, 0096, 0181,
0473, 1181
RCA 0054, 0061, 0067,
0079, 0096, 0124,
0125, 0168, 0221,
0259
Radio Shack 0019, 1056
Radix 0056
Randex 0056
Realistic 0019, 0054, 0056,
0065, 0066, 0067,
0081, 0085, 0123
ReplayTV 0633, 0635
Ricoh 0053, 0272
Runco 0058
STS 0061
Samsung 0064, 0070, 0072,
0259
Sanky 0058, 0067
Sansui 0019, 0060, 0086,
0228, 0290, 0498
Sanyo 0065, 0066, 0123,
0259
Scott 0062, 0064, 0140,
0203, 0229, 0231
Sears 0019, 0054, 0056,
0061, 0065, 0066,
0073, 0076, 0085,
0123, 0124
Semp 0064
Sharp 0067, 0081
Shintom 0091
Shogun 0070, 0259
Singer 0091
Sony 0019, 0051, 0052,
0053, 0054, 0272,
1051
Sunpak 0272
Sylvania 0019, 0054, 0062,
0100, 0129
Symphonic 0019
TMK 0055, 0227, 0259
Tatung 0060
Teac 0019, 0060
Technics 0054, 0181
Teknika 0019, 0054, 0056
Thomas 0019
Tivo 0637
Toshiba 0062, 0064, 0076,
0085, 0229, 0231,
0385
Totevision 0056, 0259
Unitech 0259
Vector 0064
Vector Research 0057, 0059
Video Concepts 0059, 0064, 0080
Videosonic 0259
Wards 0019, 0054, 0061,
0066, 0067, 0079,
0081, 0091, 0100,
0168, 0231, 0259
White Westinghouse 0228, 0297
XR-1000 0019, 0054, 0091
Yamaha 0057
Zenith 0019, 0052, 0053,
0058, 0228, 0498,
0656
Device code table
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
19
DVD setup codes
Brand Code
Aiwa 0660
Denon 0509, 0653
GE 0541
Harman/Kardon 0601
JVC 0577, 0642
Kenwood 0553
Magnavox 0522
Marantz 0558
Mitsubishi 0540
Onkyo 0522, 0646
Optimus 0590
Panasonic 0509, 0651
Philips 0522, 0558
Pioneer 0544, 0590, 0651
Proscan 0541
RCA 0541
Samsung 0592
Sharp 0649
Sherwood 0652
Sony 0552
Technics 0509
Theta Digital 0590
Toshiba 0522
Yamaha 0509, 0564
Zenith 0522, 0610
Laser Disc setup codes
Brand Code
Aiwa 0222
Carver 0083, 0213, 0342
Denon 0078, 0191
Disco Vision 0042
Funai 0222
Harman/Kardon 0213
Hitachi 0042
Magnavox 0213, 0236
Marantz 0083, 0213
Mitsubishi 0078
NAD 0078
Optimus 0078
Panasonic 0223
Philips 0083, 0213
Pioneer 0042, 0078
Quasar 0223
Realistic 0222
Samsung 0342
Sega 0042
Sony 0212, 0220
Technics 0223
Theta Digital 0213
Yamaha 0236
CD Player setup codes
Brand Code
ADC 0037
Adcom 0174, 0253
Aiwa 0143, 0176
Akai 0175
Audio Alchemy 0213
Audio-Technica 0189
BSR 0213, 0264
Burmester 0439
California Audio Labs 0048, 0322
Carrera 0213
Carver 0176, 0198, 0318,
0456
DAK 0264
DKK 0019
Denon 0022, 0892
Emerson 0174, 0183, 0324,
0488
Fisher 0107, 0193, 0198,
0361
GE 0028
Garrard 0264, 0299, 0412,
0439
Genexxa 0051, 0183, 0324
Harman/Kardon 0176, 0192, 0445
Hitachi 0051, 0174
JVC 0091
Kenwood 0047, 0056, 0209,
0645, 0700, 0845
Kodak 0306
Krell 0176
Kyocera 0037
LXI 0324
Linn 0176
Luxman 0112
MCS 0048
MTC 0439
Magnavox 0176, 0324
Marantz 0048, 0176, 0199
McIntosh 0306
Mission 0176
NAD 0038, 0318
NEC 0253
NSM 0176
Nikko 0183, 0189, 0193
Onkyo 0120, 0887
Optimus 0019, 0051, 0056,
0106, 0164, 0198,
0213, 0215, 0299,
0324, 0361, 0439,
0445, 0456, 0487,
1082
Panasonic 0048, 0322, 0386,
0771
Parasound 0213, 0439
Philips 0176, 0306, 0645
Pioneer 0051, 0263, 0324,
0487, 1082
Proton 0176
QED 0176
Quasar 0048
RCA 0028, 0072, 0174,
0198, 0324, 0783
Realistic 0174, 0183, 0198,
0199, 0439
Rotel 0176, 0439
SAE 0176
STS 0037
Sansui 0176, 0221, 0324
Device code table
Sanyo 0106, 0198
Scott 0174, 0183, 0324
Sears 0324
Sharp 0056, 0199, 0880
Sherwood 0199, 0215, 0445,
1086
Sony 0019, 0204, 0509,
0623, 0624
Soundesign 0164
Tascam 0439
Teac 0193, 0199, 0412,
0439
Technics 0048, 0322
Toshiba 0038, 0318
Vector Research 0213
Victor 0091
Wards 0072, 0176
Yamaha 0055, 0189, 0206
Yorx 0480
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
20
Amplifier setup codes
Brand Code
Aiwa 0425
Carver 0288
Curtis Mathes 0319
Denon 0179
GE 0097
Harman/Kardon 0911
JVC 0350
Linn 0288
Magnavox 0288
Marantz 0288
Optimus 0319, 0414
Panasonic 0327
Philips 0288, 0911
Pioneer 0032, 0319
Realistic 0414
Sony 0239, 0708
Soundesign 0097
Technics 0327
Toshiba 0372
Victor 0350
Wards 0032, 0097
Yamaha 0373
Cassette Player setup codes
Brand Code
Aiwa 0048, 0216, 0219
Akai 0302
Carver 0048
Denon 0095
Fisher 0093
Garrard 0327, 0458
Harman/Kardon 0048, 0201
JVC 0263, 0292
Kenwood 0089
Magnavox 0048
Marantz 0028, 0048
Mitsubishi 0302
Onkyo 0154, 0155, 0301
Optimus 0046, 0239, 0356,
0458
Panasonic 0248
Philips 0048
Pioneer 0046, 0118, 0239
Revox 0209
Sansui 0028, 0048
Sherwood 0356
Sony 0189, 0262, 0310
Teac 0327
Technics 0248
Toshiba 0360, 0361
Victor 0292
Wards 0046
Yamaha 0113, 0116
Misc. Audio setup codes
Brand Code
Aiwa 0029, 0178, 0423
Fisher 0071
Harman/Kardon 0496
JBL 0496
JVC 0092
Jerrold 0478, 0539
Nikko 0395
Paramount Pictures 0336
RCA 0075
SSI 0336
Schneider 0395
Scientific Atlanta 0479
Sony 0029, 0178, 0595
Soundesign 0395
Starcom 0478
Yorx 0395
Receiver setup codes
Brand Code
ADC 0550
Adcom 0635
Aiwa 0140, 0177, 0208,
0424, 1108, 1424
Akai 0095, 0243
Capetronic 0550
Carver 0027, 0061, 0208,
0379, 1108, 1208
Casio 0214
Clarinette 0214
Curtis Mathes 0099
Denon 0023, 0292, 0790,
1123, 1179
Emerson 0443
Fisher 0061, 0238, 0379
Garrard 0443, 0482
Harman/Kardon 0129, 0208, 0910
Inkel 0081
JBL 0129
JVC 0093
Kenwood 0046, 0061, 0096,
0205, 0332, 0333,
1046, 1071, 1332,
1588
Koss 0443
LXI 0200
Linn 0208
Lloyd's 0214
MCS 0058, 0365
Magnavox 0147, 0208, 0214,
0410, 0550, 1108,
1208
Marantz 0058, 0147, 0208,
1108, 1208
Modulaire 0214
NAD 0339
NEC 0254
Nakamichi 0116, 0366
Onkyo 0119, 0154, 0399
Optimus 0061, 0099, 0196,
0200, 0205, 0238,
0550, 0689, 0757,
0820, 1042
Panasonic 0058, 0328, 0537,
1537
Penney 0214
Philips 0208, 0410, 1108,
1208
Pioneer 0033, 0099, 0169,
0550, 0649, 1042
Proscan 1273
Quasar 0058
RCA 0073, 0365, 0379,
0549, 0550, 1173,
1273
Realistic 0182, 0200, 0214
Sansui 0208, 0212, 0365,
1108
Sanyo 0238, 0820
Scott 0182, 0341
Sharp 0205
Sherwood 0081, 0510, 0521
Sony 0177, 0187, 0493,
1061, 1077, 1177,
1277
Soundesign 0689
Sunfire 0332, 0333, 1071,
1332
Teac 0182, 0482
Technics 0058, 0227, 0328,
0537, 1327, 1328,
1537
Thorens 1208
Victor 0093
Wards 0033, 0073, 0099,
0177, 0208
Yamaha 0195, 0205, 1195
Yorx 0214
Zenith 0876
Device code table
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
Toshiba 34HF81C User manual
- Category
- LCD TVs
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
