Axis T8124-E User manual

Installation Guide

ENGLISH DEUTSCH

ITALIANO

ESPAÑOL

FRAN

Ç

AIS

AXIS T8123-E Outdoor Midspan 30 W (1-port)

AXIS T8124-E Outdoor Midspan 60 W (1-port)

Legal Considerations

Video and audio surveillance can be prohibited by laws that

vary from country to country. Check the laws in your local

region before using this product for surveillance purposes.

Electromagnetic Compatibility (EMC)

This equipment has been designed and tested to fulfill

applicable standards for:

• Radio frequency emission when installed according to the

instructions and used in its intended environment.

• Immunity to electrical and electromagnetic phenomena

when installed according to the instructions and used in

its intended environment.

USA - This equipment has been tested using a shielded

network cable (STP) and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Canada - This Class B digital apparatus complies with

Canadian ICES-003.

Europe - This digital equipment fulfills the

requirements for RF emission according to the Class B limit

of EN 55022.

Australia - This digital equipment fulfills the

requirements for RF emission according to the Class B limit

of AS/NZS CISPR 22.

Safety

This product complies with IEC/EN/UL 60950-1 and

IEC/EN/UL 60950-22, Safety of Information Technology

Equipment.

Japan - B

Korea -

ࢇ̛̛Еɼࢽࡈ%̗ࢷ࢕ળࢶଢ̛̛Ի۰

࣯Իɼࢽ߾۰یࡈଜЕʨࡶּࢶࡳԻଜֲֻҘ

एࠇ߾۰یࡈଟܹ࢑ݡТЬ

Equipment Modifications

This equipment must be installed and used in strict

accordance with the instructions given in the user

documentation. This equipment contains no

user-serviceable components. Unauthorized equipment

changes or modifications will invalidate all applicable

regulatory certifications and approvals.

Liability

Every care has been taken in the preparation of this

document. Please inform your local Axis office of any

inaccuracies or omissions. Axis Communications AB cannot

be held responsible for any technical or typographical errors

and reserves the right to make changes to the product and

documentation without prior notice. Axis Communications

AB makes no warranty of any kind with regard to the

material contained within this document, including, but not

limited to, the implied warranties of merchantability and

fitness for a particular purpose. Axis Communications AB

shall not be liable nor responsible for incidental or

consequential damages in connection with the furnishing,

performance or use of this material. This product is only to

be used for its intended purpose.

RoHS

This product complies with both the European RoHS

directive, 2002/95/EC, and the Chinese RoHS

regulations, ACPEIP.

WEEE Directive

The European Union has enacted a Directive

2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE Directive). This directive is

applicable in the European Union member states.

The WEEE marking on this product (see right) or

its documentation indicates that the product

must not be disposed of together with household waste. To

prevent possible harm to human health and/or the

environment, the product must be disposed of in an

approved and environmentally safe recycling process. For

further information on how to dispose of this product

correctly, contact the product supplier, or the local

authority responsible for waste disposal in your area.

Business users should contact the product supplier for

information on how to dispose of this product correctly. This

product should not be mixed with other commercial waste.

Support

Should you require any technical assistance, please contact

your Axis reseller. If your questions cannot be answered

immediately, your reseller will forward your queries through

the appropriate channels to ensure a rapid response. If you

are connected to the Internet, you can:

• download user documentation and software updates

• find answers to resolved problems in the FAQ database.

Search by product, category, or phrase

• report problems to Axis support staff by logging in to your

private support area

• chat with Axis support staff (selected countries only)

• visit Axis Support at www.axis.com/techsup/

ENGLISH

Safeguards

• Store the Axis product in a dry and ventilated environment.

• Avoid exposing the Axis product to vibration, shocks or heavy pressure. Do not install the product on unstable

brackets, unstable or vibrating surfaces or walls, since this could cause damage to the product.

• Only use applicable tools when installing the Axis product; excessive force could cause damage to the prod-

uct.

• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.

• Use only accessories that comply with technical specification of the product. These can be provided by Axis or

a third party.

• Installation and removal of AXIS T8123-E/T8124-E must be carried out by qualified personnel only.

• The equipment is intended only for installation in a Restricted Access Location.

• This product is not intended to become a permanent part of the building structure.

• Read this Installation Guide before connecting AXIS T8123-E/T8124-E to its power source.

• Follow basic electricity safety measures whenever connecting AXIS T8123-E/T8124-E to its power source.

• Power supply cord must not be attached to the building surface nor run through walls, ceilings, floors and

similar openings in the building structure.

• Measures must be taken to prevent physical damage to the power supply cord, including proper routing.

• A voltage mismatch can cause equipment damage and may pose a fire hazard. If the voltage indicated on the

label is different from the power outlet voltage, do not connect AXIS T8123-E/T8124-E to this

power outlet.

• US version only. All wiring and connections shall be in accordance with NFPA 70 (NEC).

• US version only. This product is fitted with a NEMA 5-15P plug for connection to the branch circuit. If other

attachment methods are required, please reference local codes and requirements for proper connection to the

branch circuit.

• AXIS T8123-E/T8124-E AC power plug shall be connected to a sealed box in order to meet

EN 60529 level IP66 and NEMA 250 level 4x.

• AXIS T8123-E/T8124-E AC power lines shall be connected to the socket-outlet, which shall be installed near

the equipment and easily accessible.

• International version only. AXIS T8123-E/T8124-E AC power lines shall be connected via an external 2-pole

circuit breaker to the normal building installation wiring.

• AXIS T8123-E/T8124-E "DATA IN" and "DATA PWR OUT" ports are shielded RJ45 data sockets. They cannot be

used as Plain Old Telephone Service (POTS) sockets. Only RJ45 data connectors can be connected to these

sockets.

• Ensure cable length from Ethernet network source does not exceed 100 m (333 ft). AXIS T8123-E/T8124-E is

not a repeater and does not amplify the Ethernet data signal.

• Use a splitter if desired, ensure that the splitter is connected close to the terminal and not on the Midspan.

• Designed to meet GR-1089-CORE lightning protection demands.

• This Axis product shall be used in compliance with local laws and regulations.

• Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for service matters

• Installation and removal of AXIS T8123-E/T8124-E must be carried out by qualified personnel only.

Page is loading ...

AXIS T8123-E/T8124-E Installation Guide Page 5

ENGLISH

AXIS T8123-E/T8124-E

Installation Guide

Package Contents

Note: Ethernet cable, RJ45 male connectors and mounting screws are not part of the delivery

Functions and Features

AXIS T8123-E/T8124-E 1-Port 802.3at Gigabit PoE Outdoor Midspan injects power over data

carrying Ethernet cabling. It maintains IEEE802.3at and IEEE802.3af standards. These power levels

allow usage by a new range of Ethernet-based applications such as video phones, 802.11n Access

Points, WiMAX Transmitters, PTZ cameras and more. AXIS T8123-E/T8124-E DATA PWR OUT port is

designed to carry Gigabit Ethernet data and power over a standard CAT5e cable, delivered through

4-pairs (Alt A: pins 1,2(-) / 3,6(+) and Alt B: pins 4,5(+) / 7,8(-)).

AXIS T8123-E/T8124-E

Midspan with pre-installed power cable

(power cable country specific)

International

USA

Mounting kit 2X RJ45 male plug waterproof

connectors covers

Grounding wire

Printed material Installation Guide (this document)

AC power cable color code Line Neutral Protective earth

US version - NFPA 70 (NEC) Black White Green

International version - IEC 60445 Brown Blue Green/Yellow

Page 6 AXIS T8123-E/T8124-E Installation Guide

Install the Hardware

AXIS T8123-E/T8124-E may be wall or bench mounted using the rear side holes.

Note the following before mounting AXIS T8123-E/T8124-E to a fixed location:

• Do not cover AXIS T8123-E/T8124-E or block the airflow to the product with any foreign

object. Keep AXIS T8123-E/T8124-E away from excessive heat and humidity, and free from

vibration and dust.

• Ensure that the cable length from the Ethernet network source to your Axis video product

does not exceed 100 meters (333 ft). AXIS T8123-E/T8124-E is not a repeater and does not

amplify the Ethernet data signal.

• There is no "on-off" switch; simply plug AXIS T8123-E/T8124-E into an AC power outlet

installed near the equipment and easily accessible. For the international version of

AXIS T8123-E/T8124-E AC power line shall also be connected via an external 2-pole circuit

breaker to the normal building installation wiring.

To mount:

1. Fasten AXIS T8123-E/T8124-E with three screws. See Fig 1 (screw holes are marked 1, 2 and 3).

2. Connect one end of the grounding wire to EARTH GROUND (see fig 1b) and the other end to an

appropriate ground location. Make sure that this step (2) is performed before connecting

AXIS T8123-E/T8124-E to its power source! Use the supplied ground wire or a wire of equal or

larger area.

Note: When mounting the AXIS T8123-E/T8124-E make sure to use appropriate screws and plugs

for the surface (wood, concrete etc.). Do not unscrew the four pre-mounted screws

located in every corner of the product, since this violate the warranty of the product.

46.36

196

Fig 1

Fig 1b

1

EARTH GROUND

2 3

AXIS T8123-E/T8124-E Installation Guide Page 7

ENGLISH

3. Thread male plug waterproof connector cover (A,B and C) on to the Ethernet cable. See Fig 3.

4. Attach the Ethernet cable to DATA IN. See Fig 2.

5. Thread plug (A) over the RJ45 male plug, connected to DATA IN. See Fig 3.

6. Thread housing (B) over the plug and screw (hand tight only). See Fig 3.

7. Thread cover (C) over the connector and screw (hand tight only). See Fig 3.

8. Repeat steps 2 to 6 for DATA PWR OUT.

9. Connect AXIS T8123-E/T8124-E to an AC power line (100-240 V AC) complying with the

information in the Safeguards.

International version only. See Fig 4.

Note: Do not use cross over cable between AXIS T8123-E/T8124-E output port and load device.

DATA IN

DATA PWR OUT

LINE AC

L

N

PE

L

PE

Fig 2

Fig 3

RJ45

male plug

A

B

C

RJ45 male plug

waterproof

connector

cover

Fig 4

INCOMING

MAINS VOLTAGE

EXTERNAL PROTECTIVE

GROUND WIRE

Page 8 AXIS T8123-E/T8124-E Installation Guide

Specifications

Environmental

Electrical

Interface

Mode Temperature Relative humidity IP Class

Operating

AXIS T8123-E

-40°C to 50°C for 30 Watts (-40°F to 131°F)

-40°C to 65°C for 15.4 Watts (-40°F to149°F)

10 to 100%

(condensing) IP66

Operating

AXIS T8124-E

-40°C to 50°C for 60 Watts (-40°F to 131°F)

-40°C to 65°C for 30 Watts (-40°F to 149°F)

Storage -40°C to 85°C (-40°F to 185°F) Max 95%

(non-condensing)

N/A

Input Voltage 100-240 V AC (50/60 Hz)

Input Current AXIS T8123-E 1 Ampere (max)

Input Current AXIS T8124-E 2 Ampere (max)

Available Output Power (max) AXIS T8123-E 30 Watt

Available Output Power (max) AXIS T8124-E 60 Watt

Nominal Output Voltage 55 V DC

Input (DATA IN):

Ethernet 10/100/1000Base-T

RJ45 female socket

Output (DATA PWR OUT):

Ethernet 10/100/1000Base-T, plus 55 V DC

RJ45 female socket, with DC voltage on wire pairs

1-2 & 3-6, 4-5 & 7-8.

Power Cable (LINE AC) Pre-installed 3m power cable

AC power cable color code Line Neutral Protective earth

US version - NFPA 70 (NEC) Black White Green

International version - IEC 60445 Brown Blue Green/Yellow

AXIS T8123-E/T8124-E Installation Guide Page 9

ENGLISH

Troubleshooting

Warranty

For information about Axis product warranty and thereto related information, see

www.axis.com/warranty

Symptom Corrective Steps

AXIS T8123-E/

T8124-E does

not power up

1. Verify a reliable power cord is used.

2. Verify voltage at the power inlet is between 100-240 V AC.

3. Remove and reapply power and check the indicators on the powered device

during power up sequence.

A port indicator

on the powered

device is not lit

and the device

does not operate

1. Verify the Midspan detects a device.

2. Verify that the device is designed for PoE operation

3. Verify you are using a standard Category 5/5e/6, straight-wired cable, with

four pairs.

4. If an external power splitter is in use, replace it with a known good splitter

5. Ensure input Ethernet cable is connected to the DATA IN port.

6. Verify that the device is connected to the DATA PWR OUT port.

7. Try to reconnect the same powered device into a different Midspan. If it

works, there is probably a faulty port or RJ45 connection.

8. Verify there is no short over any of the twisted pair cables or over the

RJ45 connectors.

The end device

operates, but

there is no data

link

1. Verify the port indicator on the powered device is continuously lit.

2. If an external power splitter is in use, replace it with a known-good splitter.

3. Verify that for this link, you are using standard UTP/FTP Category 5 straight

(non-crossover) cabling, with all four pairs.

4. Verify Ethernet cable length is less than 100 meters from Ethernet source to

load/remote terminal.

5. Try to reconnect the same powered device into a different Midspan. If it

works, there is probably a faulty port or RJ45 connection.

Page is loading ...

Page 16 AXIS T8123-E/T8124-E Guide d'installation

DATA IN

DATA PWR OUT

LINE AC

L

N

PE

L

PE

Fig 2

Fig 3

RJ45

Prise mâle

A

B

C

Prise mâle RJ45

cache

connecteur

étanche

Fig 4

TENSION

D'ENTRÉE

CONDUCTEUR DE TERRE

DE PROTECTION EXTERNE

D'ALIMENTATION

Page is loading ...

Pagina 32 AXIS T8123-E/T8124-E Guida all'installazione

DATA IN

DATA PWR OUT

LINE AC

L

N

PE

L

PE

Fig 2

Fig 3

RJ45

maschio RJ-45

A

B

C

Connettore maschio RJ45

Copertura impermeabile

Fig 4

TENSIONE DI RETE

IN INGRESSO

CAVO DI TERRA

DI PROTEZIONE ESTERNO

Page is loading ...

Installation Guide

Ver.1.2

AXIS T8123-E/T8124-E

Printed: November 2012

Part No. 49679

Axis T8124-E User manual

This manual is also suitable for

Axis T8124-E User manual

in other languages

Related papers

Other documents