SignaMax 10/100 Ethernet Extender User guide

Category
Network extenders
Type
User guide
Signamax Connectivity Systems
Industrial 10/100BASE-TX Ethernet Extender
U SER S G U I D E
Signamax Connectivity Systems
Industrial Ethernet Extender
Model 065-1167A
User’s Guide
Signamax Industrial Ethernet Extender
FCC Warning
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with this user’s guide, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the user
may be required to take adequate measures.
Signamax Connectivity Systems from Advanced Electronic
Supports Products Inc. All rights reserved.
1
Signamax Industrial Ethernet Extender
Trademarks
Product names mentioned in this manual may be trademarks
or registered trademarks of those products and are hereby
acknowledged.
Ethernet is a trademark of Xerox Corporation.
Signamax is a trademark of Advanced
Electronic Support Products, Inc.
2
Signamax Industrial Ethernet Extender
Preface
Audience
This guide is designed for the person who installs, configures,
deploys, and maintains the Ethernet network. This document
assumes the reader has moderate hardware, computer, and
Internet skills.
Safety and Warnings
This guide uses the following symbols to draw your attention
to certain information.
Symbol
Meaning
Description
Note
Notes emphasize or supplement important points
of the main text.
Tip
Tips provide helpful information, guidelines, or
suggestions for performing tasks more effectively.
Warning
Warnings indicate that failure to take a specified
action could result in damage to the device, or
could result in serious bodily injury.
Electric
Shock
Hazard
This symbol warns users of electric shock hazard.
Failure to take appropriate precautions such as not
opening or touching hazardous areas of the
equipment could result in injury or death.
3
Signamax Industrial Ethernet Extender
Typographic Conventions
This guide also uses the following typographic conventions.
Convention
Bold
Indicates text on a window, other than the window title, including
menus, menu options, buttons, fields, and labels.
Italic
Indicates a variable, which is a placeholder for actual text
provided by the user or system. Angled brackets (< >) are also
used to indicate variables.
screen/code
Indicates text that is displayed on screen or entered by the user.
< > angled
brackets
Indicates a variable, which is a placeholder for actual text
provided by the user or system. Italic font is also used to indicate
variables.
[ ] square
brackets
Indicates optional values.
{ } braces
Indicates required or expected values.
| vertical bar
Indicates that you have a choice between two or more options or
arguments.
4
Signamax Industrial Ethernet Extender
Contents
FCC Warning _________________________________ 1
CE Mark Warning _____________________________ 1
Trademarks __________________________________ 2
Preface _____________________________________ 3
Audience _______________________________________ 3
Safety and Warnings _____________________________ 3
Typographic Conventions _________________________ 4
Contents ____________________________________ 5
Introduction _________________________________ 6
Key Features ____________________________________ 7
Quick Start Guide ________________________________ 8
Unpacking the Hardware __________________________ 9
Hardware Features _______________________________ 9
Installing the Industrial Ethernet Extender ___________ 16
Troubleshooting ________________________________ 21
Additional Troubleshooting Suggestions ____________ 23
Specifications __________________________________ 24
5
Introduction
Congratulations on your purchase of the 065-1167A
Industrial Ethernet Extender. This Industrial Ethernet
Extender is a state-of-the-art IEEE-compliant network
solution designed for users who require
high-performance to eliminate bottlenecks and increase
productivity.
To simplify installation, the Industrial Ethernet Extender
is shipped ready for use.
065-1167A Industrial Ethernet Extender
6
Signamax Industrial Ethernet Extender
Key Features
This section summarizes the key features of the 065-1167A
Industrial Ethernet Extender.
One 10/100Base-TX Ethernet port with RJ-45 connector
Auto negotiation of speed and duplex mode on Ethernet
port
Auto MDIX on Ethernet port
Complies with IEEE 802.3 10Base-T and IEEE 802.3u
100Base-TX standards
One Ethernet Extender port with RJ-11 connector or
Termianl Block
Ethernet Extender port auto senses the speed
DIP switch for configuring Ethernet Extender Auto or
Local mode, Symmetic or Asymmetric mode, and
Performance or Standard mode
Status LEDs
External AC to DC power adapter
7
Signamax Industrial Ethernet Extender
Quick Start Guide
Description
For Reference, See…
Find a Location for the Industrial Ethernet
Extender
Set the Industrial Ethernet Extender on a flat
surface, Wall-mount, or DIN-Rail mount.
” (page 16)
Connect to the 10/100 Mbps Ethernet Port
Connect one end of a Category 5 or better
Ethernet cable to the Ethernet port of a
computer, printer, network storage, or
other network device.
Connect the other end to a 10/100 Mbps
RJ-45 port on the Industrial Ethernet
Extender.
10/100 Mbps RJ-45 Port"
(page 10)
and
Connecting to the 10/100
Mbps RJ-45 Port” (page 18)
Connect to the Ethernet Extender Port
Insert the voice grade copper wire between
one pair of Ethernet Extenders via Ethernet
Extender port (RJ-11 connector or Terminal
Block).
Power On
Connect the female end of the supplied AC
power adapter cable to the power
receptacle on the back of the Industrial
Ethernet Extender.
Connect the 3-pronged end of the AC
power adapter cable to a grounded
3-pronged AC outlet.
Wait for the Industrial Ethernet Extender to
complete its Power On Self Test.
Confirm that the LEDs for ports connected
to a device are green. If not, replace the
Ethernet cable, and then check the port
LED again.
Applying AC Power” (page 19)
8
Signamax Industrial Ethernet Extender
Unpacking the Hardware
Unpack the items and confirm that no items are missing or
damaged. Your package should include:
One 065-1167A Industrial Ethernet Extender
One external power adapter
One CD containing this user’s guide
If any item is damaged or missing, notify your authorized
representative. Keep the carton, including the original
packing material, in case you need to store the product or
return it.
Hardware Features
The following sections describe the hardware features of
the 065-1167A Industrial Ethernet Extender.
Front Panel
The figure below shows the front panels of the 065-1167A
Industrial Ethernet Extender.
9
Signamax Industrial Ethernet Extender
Front Panel
10/100 Mbps RJ-45 Port
The 065-1167A Industrial Ethernet Extender has one
10/100 Mbps RJ-45 port. This port is an auto-sensing,
auto-MDIX 10/100 Mbps port.
When you insert a cable into an RJ-45 port, the Industrial
Ethernet Extender:
Determines whether the cable is a straight-through or
crossover cable.
Automatically ascertains the maximum speed (10 or 100
Mbps) and duplex mode (half- or full-duplex) of the
attached device.
After determining this information, the Industrial Ethernet
Extender configures the RJ-45 port automatically to enable
communications with the attached device, without requiring
user intervention.
10
Signamax Industrial Ethernet Extender
Ethernet Extender Port
The 065-1167A Industrial Ethernet Extender has one
Ethernet Extender port (RJ-11 connector or Terminal Block.
Insert the voice grade copper wire between one pair of
Ethernet Extenders via Ethernet Extender port (RJ-11
connector or Terminal Block). One device must be set to
LOC mode and the other to Auto mode when two devices
are connected.
LEDs
The 065-1167A front panel LEDs show power and
link/activity status. The following table summarizes the
LEDs on the Industrial Ethernet Extender.
11
Signamax Industrial Ethernet Extender
Front Panel LEDs
LED
Color
Status
Description
PWR
Green
ON
Receiving power.
OFF
Power off.
Ethernet Extender Port
Link/Activity
Green
ON
Connection is established.
OFF
No connection is established.
Flashing
Port is sending or receiving data.
Per
Green
ON
Performance mode.
OFF
Standard mode.
RMT
Green
ON
Remote mode.
LOC
Green
ON
Local mode.
SYM
Green
ON
Symmetric mode.
ASM
Green
ON
Asymmetric mode.
Line Speed
Green
ON
Displays the link speed in Mbps.
10/100TX Port
Link/Activity
Green
ON
Valid network connection.
OFF
No data transmission on port.
Flashing
Port is sending or receiving data.
Speed
Yellow
ON
Link speed at 100Mbps.
OFF
Link speed at 10Mbps.
12
Signamax Industrial Ethernet Extender
Rear Panel
The 065-1167A rear panel has a receptacle for connecting
the supplied external power adapter. Use only the external
power adapter supplied with the Industrial Ethernet
Extender.
Rear Panel
DIP Switch Settings
Switch
Setting
Description
1
AUTO
Default. Recommended setting for all Ethernet extenders.
LOC
Local mode. Connected extenders must be set to Auto.
2
SYM
Symmetric transmission mode
ASM
Asymmetric transmission mode
3
Per
Peformance mode: Faster speed with less noise immunity
Std
Standard mode: Standard speed with better noise immunity
13
Signamax Industrial Ethernet Extender
Symmetric and Asymmetric Transmission
Modes
Symmetric Mode provides a balanced data rate for upstream
and downstream. This mode is suitable for network
extension.
Similar transmission rates for upstream and downstream.
In asymmetric mode, the downstream data rate is higher
than the upstream. This mode is suitable for applications
such as IP cameras.
Higher transmission rate from Local to Remote.
14
Signamax Industrial Ethernet Extender
Bottom Panel (Not shown)
The 065-1167A bottom panel has a product label that
shows regulatory compliance, product serial number, and
other information.
Top Panel
There are five LEDs on the top casing, which indicate the
current transmission speed.
15 15
Signamax Industrial Ethernet Extender
Installation
Before you install your Industrial Ethernet Extender, be sure
your operating environment meets the following operating
environment requirements.
Site Requirements
Parameter
Requirements
Desktop installations
DIN-Rail installations
Wall Mount installations
Provide a flat table or shelf surface.
Top hat type 35mm.
Stably mount on wall surface.
Access
Locate the Industrial Ethernet Extender in a position
that lets you access the front panel RJ-45 port and
Ethernet Extender port, view the front panel LEDs,
and access the rear-panel power connector.
Power source
Provide a power source within 6 feet (1.8 meters) of
the installation location. Power specifications for the
Industrial Ethernet Extender are shown in Appendix
A. Be sure the AC outlet is not controlled by a wall
switch, which can accidentally turn off power to the
outlet and the Industrial Ethernet Extender.
Environmental
Temperature:
Install the Industrial Ethernet Extender in a dry area,
with ambient temperature between -10 and 60ºC (14
and 140ºF). Keep the Industrial Ethernet Extender
away from heat sources such as direct sunlight,
warm air exhausts, hot-air vents, and heaters.
Operating humidity:
The installation location should have a maximum
relative humidity of 95%, non-condensing.
16
Signamax Industrial Ethernet Extender
Parameter
Requirements
Ventilation:
Do not restrict airflow by covering or obstructing the
rear and side panels of the Industrial Ethernet
Extender. Keep at least 2 inches (5.08 centimeters)
free on all sides for cooling.
Be sure there is adequate airflow in the room where
you intend to install the Industrial Ethernet Extender.
Operating conditions:
Keep the Industrial Ethernet Extender at least 6 ft
(1.83 m) away from nearest source of
electromagnetic noise, such as a photocopy
machine.
Stacking
If you intend to stack two or more Industrial Ethernet
Extenders, be sure:
The mounting surface can safely support the
stack.
There is adequate space around the stack for
ventilation and cooling.
Installing the Industrial Ethernet Extender
You can install your Industrial Ethernet Extender on a flat
surface, DIN-Rail, or wall with other equipment.
If installing the Industrial Ethernet Extender on a
desktop, shelf, DIN-Rail, or wall, allow sufficient
ventilation space between the device and the objects
around it.
065-1167A Industrial Ethernet Extender Dimensions:
80.3 x 109.2 x 23.8mm (W x D x H) (3.16 x 4.3 x 0.94)
17
Signamax Industrial Ethernet Extender
Connecting to the 10/100 Mbps RJ-45 Port
The front panel has one 10/100 Mbps RJ-45 port. To
prevent ESD damage, follow normal board and component
handling procedures.
To connect devices to the 10/100 Mbps RJ-45 port:
1. Insert one end of a Category 5 or better Ethernet cable
into a Ethernet port.
2. Insert the other cable end into the Ethernet port of a
computer, printer, network storage, or other network
device.
Connecting to Ethernet Extender Port
The front panel of the Industrial Ethernet Extender provides
one RJ-11 connector or Terminal Block (see “Ethernet
Extender Port” on page 11). To prevent ESD damage,
follow normal board and component handling procedures.
To connect the Industrial Ethernet Extender’s Ethernet
Extender port:
Insert the voice grade copper wire between one pair of
Ethernet Extenders via Ethernet Extender port (RJ-11
connector or Terminal Block). One device must be set to
LOC mode and the other to Auto mode when two devices
are connected.
18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31

SignaMax 10/100 Ethernet Extender User guide

Category
Network extenders
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI