EtherWAN ED3541 Series Quick Installation Guide

Brand
EtherWAN
Model
ED3541 Series
Category
Network switches
Type
Quick Installation Guide

EtherWAN ED3541 Series

The EtherWAN ED3541 Series is a hardened Ethernet extender that allows you to extend the range of your Ethernet network over long distances using voice-grade copper wire. It is ideal for use in harsh environments, such as industrial settings, outdoor applications, and remote locations.

The ED3541 Series is capable of transmitting data at speeds of up to 100 Mbps over distances of up to 2600 meters (8530 feet). It supports both 10/100BASE-TX and 10/100BASE-FX connections, and it can be used to connect devices such as IP cameras, sensors, and PLCs to your network.

The ED3541 Series is also equipped with a number of features that make it easy to use and manage. These features include:

EtherWAN ED3541 Series

The EtherWAN ED3541 Series is a hardened Ethernet extender that allows you to extend the range of your Ethernet network over long distances using voice-grade copper wire. It is ideal for use in harsh environments, such as industrial settings, outdoor applications, and remote locations.

The ED3541 Series is capable of transmitting data at speeds of up to 100 Mbps over distances of up to 2600 meters (8530 feet). It supports both 10/100BASE-TX and 10/100BASE-FX connections, and it can be used to connect devices such as IP cameras, sensors, and PLCs to your network.

The ED3541 Series is also equipped with a number of features that make it easy to use and manage. These features include:

W70G-ED3541XQ5 Page 1
Installation Guide
ED3541 Series | Hardened Ethernet Extender
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 03/29/2023
1 Unpacking
Unpack the items. Your package should include:
▪ One ED3541 hardened Ethernet extender
If items are missing or damaged, notify your
EtherWAN representative. Keep the carton and
packing material.
2 Select a Location
▪ Installations: Desktop, DIN-Rail mount.
▪ Identify a power source within 6 feet (1.8 meters).
▪ Choose a dry area with ambient temperature
between -40 and 75ºC (-40 and 167ºF).
▪ Keep away from heat sources, sunlight, warm air
exhausts, hot-air vents, and heaters.
▪ Be sure there is adequate airflow.
▪ Keep the device at least 6 ft (1.83 m) away from
the nearest source of electromagnetic noise, such
as a photocopy machine.
3 LED Indicators
LED
Color
Power 1, 2
Green
Ethernet Extender Port
Link/Activity
Green
Line Speed
Green
10/100TX Port
Link/Activity
Green
Speed
Yellow
W70G-ED3541XQ5 Page 2
Installation Guide
ED3541 Series | Hardened Ethernet Extender
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 03/29/2023
4 Connection
▪ Insert one end of the Ethernet cable into a switch
port.
▪ Connect the other end into the Ethernet port of
the device.
▪ Insert the voice grade copper wire between one
pair of Ethernet Extenders via Ethernet Extender
port (RJ-11 connector or Terminal Block).
Distance and data rates for Ethernet Extender ports:
Distance (m)
Data Rate (Mbps)
300
100
400
80
600
60
800
40
2600
1
This distance/data rate information is measured
according to testing standards in the EtherWAN
laboratory. The actual installation and connection
speed will be affected by the quality of copper wire
and the impact of noise disturbance.
5 DIP Switch Settings
Pin
Up
Down
DIP Switch 1 (Site)
Auto mode
Local mode
DIP Switch 2 (LDR)
Turn on link
down relay
Turn off link
down relay
Auto mode: This is the factory default setting. The
Extender will automatically select the Extender port to
operate in Local or Remote mode.
Local mode: Operation mode of the Extender is fixed
as Local mode. A pair of Extenders can only have one
Extender set to Local mode.
Connection establishment time for Extender port:
▪ One Extender is set as Local mode, the other is set
as Auto mode: Around 40 seconds.
▪ If a pair of Extenders are set to Auto mode,
connection establishment time may be longer,
possibly up to a few minutes.
NOTE: After making changes to the position of any DIP
switch, the Ethernet Extender must be rebooted for
the new settings to take effect.
Ethernet Extender Connection
RJ-11 and Terminal Block port pinouts
Pin 3: Tip, Pin 4: Ring.
Use a telephone line to connect two RJ-11 or Terminal
Block ports between two Ethernet Extenders.
6 Apply DC Power
▪ Connect the DC power cord to the plug-able
terminal block on the Ethernet Extender, and then
plug it into a standard DC outlet.
▪ Connect the ground connection from the terminal
block to the grounding surface.
Manufacturer information:
EtherWAN Systems, Inc.
33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New
Taipei City, 221 Taiwan
The full product manual can be downloaded from:
www.etherwan.com
  • Page 1 1
  • Page 2 2

EtherWAN ED3541 Series Quick Installation Guide

Brand
EtherWAN
Model
ED3541 Series
Category
Network switches
Type
Quick Installation Guide

EtherWAN ED3541 Series

The EtherWAN ED3541 Series is a hardened Ethernet extender that allows you to extend the range of your Ethernet network over long distances using voice-grade copper wire. It is ideal for use in harsh environments, such as industrial settings, outdoor applications, and remote locations.

The ED3541 Series is capable of transmitting data at speeds of up to 100 Mbps over distances of up to 2600 meters (8530 feet). It supports both 10/100BASE-TX and 10/100BASE-FX connections, and it can be used to connect devices such as IP cameras, sensors, and PLCs to your network.

The ED3541 Series is also equipped with a number of features that make it easy to use and manage. These features include:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents