ATake Sound Orator Operating instructions
- Type
- Operating instructions
Welcome
Thank you for your purchase of the ATake™ Audio Amplifier. You are on your way to living a life free of wires. But first, please read this user’s guide carefully
for important information concerning operation, performance and safety.
You will find the ATake™ Audio Amplifier to be convenient and perfect for watching video and operating the touch screen to enjoy a mini multimedia feast
anytime anywhere.
Read the following recommendations before using the ATake™ Audio Amplifier. Following these you will be able to enjoy our product for many years.
Keep it dry and don’t take it to damp places to avoid the product’s internal circuit being affected.
Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort
certain plastic parts.
Don’t expose the product to cold areas. It may damage the internal circuit board.
Don’t try to disassemble the product as it may get damaged if you are not professional.
Don’t let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.
Don’t use intensive chemical products or detergent to clean the product.
Don’t scratch the surface with sharp things.
Please turn off the product if you don’t use it for a long time.
NOTE:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PACKAGE CONTENTS
• ATake Sound Orator Audio Amplifier
• Micro USB power cable
• 3.5mm right angle audio cable
• Instruction manual
Care and maintenance
2013.01
www.atake.com
MADE IN CHINA
TYPE: ASP-708
Sound
Orator
Place-n-Play
Audio Amplifier
Operating Instructions
1. Decorative translucent board 5. Loudspeaker 9. Micro USB charging cable (1.2m)
2. Blue LED Indicators (Working) 6. ON/OFF switch 10. Right angle audio cable (0.18m)
3. Red LED Indicator (Charging) 7. Micro USB charging port
4. Inductive sensing area 8. AUX (line in) port
FIGURE:
Charge your amplier
MAKE SURE THAT YOUR AMPLIFIER IS FULLY CHARGED BEFORE USING IT. A full charge is approximately 2 to 2.5
hours and plays continuously 4 hours then.
1. Connect to a USB charging cable or use an additional USB to DC adapter (not included) to charge.
2. When the LCD indicators are RED, the device is charging.
3. The LED indicators go off when the device is fully charged.
Broadcast music from your amplier, just Place-n-Play
1. Switch to turn “ON” the amplifier. The BLUE Indicators remain.
2. Turn on the music on your mobile phone, and place it on the inductive area.
3. Start listening to the music.
4. When the battery is low, the BLUE indicators blink continueously and the amplifier turns off automatically in
two minutes. Please charge your amplifier
immediately.
5. Please switch to turn OFF the amplifier if you don’t use it for a long time to prolong the battery life.
Connect to other music equipment
Connect to other portable media players to the AUX line-in port on the amplifier using the supplied cable.
PLEASE NOTE:
This product works perfect with speaker position at the buttom of the mobile phones; especially for Apple
iPhone series of smartphones. The audio amplification effect of the mobile phones may be affected or failed for
the speaker position is not in the inductive sensing area.
This product is an inductive audio amplifier, any signal interference sound from the phone will be amplified.
It’s not the product defective. Please re-adjust the phone's reception angle or strengthen signal receiving in
order to achieve a better audio amplification effect.
Troubleshooting
Q: Can not turn on the amplifier
A: Please use the Micro USB charging cable for charging, and then turn on the amplifer again.
Q: Can’t hear sound from the amplifer
A: Check whether your device is properly placed in the sensing area.
5
1
3
2
4
6 7 8
DC 5V
AUXON/OFF
9 10
-
1
-
2
