LXE 2325 Reference guide

Brand: LXE

Model: 2325

Category: Print & Scan

Type: Reference guide

2325 Vehicle Printer

Reference Guide

IMPORTANT NOTICE

The LXE 2325 Vehicle Printer is obsolete.

This electronic manual has been made available as a courtesy to LXE's

2325 customers. Please contact your LXE customer support representative

for assistance.

An EMS Technologies Company

2325A138REFGD

E-EQ-2325VPRG-A-ARC

November 1999

Revision A

Notice:

LXE Inc. reserves the right to make improvements or changes in the products described in this manual at any time without

notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, LXE assumes no

liability resulting from any errors or omissions in this document, or from the use of the information contained herein.

This manual is copyrighted. All rights are reserved. This document may not, in whole or in part, be copied, photocopied,

reproduced, translated or reduced to any electronic medium or machine-readable form without prior consent, in writing, from

LXE Inc.

125 Technology Parkway, Norcross, GA 30092 U.S.A. (770) 447-4224

LXE is a registered trademark of LXE Inc. All other brand or product names are trademarks or registered trademarks of their

Adobe Systems Incorporated." applies.

Note: The original equipment’s Reference Manual is copyrighted by Percon® Inc. This manual has been amended by

LXE® Inc., for the 2325 and Docking Stations with Percon’s express permission.

Notice:

The long term characteristics or the possible physiological effects of radio frequency electromagnetic fields have not been

investigated by UL.

FCC Information:

This device complies with FCC Rules, part 15. Operation is subject to the following conditions:

1. This device may not cause harmful interference

and

2. This device must accept any interference that may be received, including interference that may cause undesired

operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15

of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Warning: Changes or modifications to this device not expressly approved by LXE, Inc., could void the user’s authority to

operate this equipment.

Shielded cables must be used with this unit to ensure compliance with the FCC Class A limits.

EMC Directive Requirements:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may

be required to take adequate measures.

Industry Canada:

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

Approvals:

EMI / EMC Standards:

FCC Part 15 Subpart B

EN 55022 : 1998

Immunity:

EN55024:1998

EN61000-4-2:1995

EN61000-4-3:1995

EN61000-4-4:1995

EN61000-4-5:1995

EN61000-4-6:1996

EN61000-4-8:1993

E-EQ-2325VPRG-A-ARC 2325 Vehicle Printer Reference Guide

Table of Contents

CHAPTER 1 INTRODUCTION AND SPECIFICATIONS 1-1

Introduction ........................................................................................ 1-1

About This Guide .......................................................................................1-2

Document Conventions ..............................................................................1-2

Connect Power Supplies ................................................................... 1-3

Physical Installation ...................................................................................1-3

Internal 12V Battery Instruction ..............................................................1-3

Connect the Battery ..................................................................................1-3

Battery Life...............................................................................................1-4

Vehicle to Battery Connection...................................................................1-5

Fuse Replacement.......................................................................................1-6

Connectors ......................................................................................... 1-7

Optional RS-232 Connector ......................................................................1-7

Optional Internal Modem..........................................................................1-8

Specifications and Features.............................................................. 1-9

Printer Keypad.................................................................................. 1-11

Printer Panel Buttons...............................................................................1-11

Printer Self Test........................................................................................1-12

Printer Panel Indicators ..........................................................................1-13

Printer Panel Conditions .........................................................................1-13

Cradle Indicators......................................................................................1-14

Configuration.................................................................................... 1-15

Dip Switches..............................................................................................1-15

Default Factory Settings ..........................................................................1-15

Baud Rate Selection .................................................................................1-16

ii Table of Contents

2325 Vehicle Printer Reference Guide E-EQ-2325VPRG-A-ARC

CHAPTER 2 PROGRAMMING THE PRINTER 2-1

Defaults ...............................................................................................2-1

Control Commands ............................................................................ 2-2

Command Summary List.......................................................................... 2-2

Command Descriptions ..................................................................... 2-6

Printer Operation Control ........................................................................ 2-6

Initialization ............................................................................................. 2-6

Low-Temperature Operation Mode ......................................................... 2-9

Data Control........................................................................................... 2-10

Horizontal Motion.................................................................................. 2-11

Carriage Return Control......................................................................... 2-12

Print Quality........................................................................................... 2-13

Print Direction........................................................................................ 2-14

Paper Empty Sensor Control.................................................................. 2-15

Paper Feed Control.................................................................................. 2-16

Vertical Feed.......................................................................................... 2-16

Skip-Over Perforation............................................................................ 2-18

Line Spacing .......................................................................................... 2-19

Page Format Control ............................................................................... 2-21

Page Length............................................................................................ 2-21

Margins .................................................................................................. 2-22

Tab ......................................................................................................... 2-24

Character Control ............................................................................. 2-26

Font Selection ........................................................................................... 2-26

Character Pitch ........................................................................................ 2-27

Character Style ........................................................................................ 2-30

Miscellaneous ........................................................................................... 2-38

Bit Image Control.............................................................................. 2-39

Creating 8-Pin Bit Images....................................................................... 2-39

Density Change ........................................................................................ 2-45

Table of Contents iii

E-EQ-2325VPRG-A-ARC 2325 Vehicle Printer Reference Guide

CHAPTER 3 CHARACTER SET TABLES 3-1

Character Set 1................................................................................... 3-1

Character Set 2................................................................................... 3-2

All-Character Code Set ...................................................................... 3-3

Multilingual Character Set 1.............................................................. 3-4

Multilingual Character Set 2.............................................................. 3-5

Multilingual, All-Character Set .......................................................... 3-6

Other 17 Countries............................................................................. 3-7

CHAPTER 4 SOFTWARE CONTROLLED UNIVERSAL

ERIAL SWITCH (SCUSS) 4-1

Introduction ........................................................................................ 4-1

Example.......................................................................................................4-2

SETPRINT.C........................................................................................ 4-3

INDEX

Illustrations

Figure 1-1 2325 In the Cradle of the Vehicle Printer...........................................................1-1

Figure 1-2 Proper Connection of the Vehicle Cable ............................................................1-5

Figure 1-3 Three Connectors on Vehicle Printer .................................................................1-7

Figure 1-4 RS-232 Pinouts...................................................................................................1-7

Figure 1-5 9-Pin RS-232 Description...................................................................................1-8

Figure 1-6 Printer Panel Buttons........................................................................................1-11

Figure 1-7 Printer Panel Indicators ....................................................................................1-13

Figure 1-8 Cradle Indicators ..............................................................................................1-14

iv Table of Contents

2325 Vehicle Printer Reference Guide E-EQ-2325VPRG-A-ARC

E-EQ-2325VPRG-A-ARC 2325 Vehicle Printer Reference Guide

Table of Contents

CHAPTER 1 INTRODUCTION AND SPECIFICATIONS 1-1

Introduction ........................................................................................ 1-1

About This Guide ........................................................................................1-2

Document Conventions ...............................................................................1-2

Connect Power Supplies ................................................................... 1-3

Physical Installation ....................................................................................1-3

Internal 12V Battery Instruction ...............................................................1-3

Connect the Battery ..................................................................................1-3

Battery Life...............................................................................................1-4

Vehicle to Battery Connection....................................................................1-5

Fuse Replacement........................................................................................1-6

Connectors ......................................................................................... 1-7

Optional RS-232 Connector .......................................................................1-7

Optional Internal Modem...........................................................................1-8

Specifications and Features.............................................................. 1-9

Printer Keypad.................................................................................. 1-11

Printer Panel Buttons................................................................................1-11

Printer Self Test.........................................................................................1-12

Printer Panel Indicators ...........................................................................1-13

Printer Panel Conditions ..........................................................................1-13

Cradle Indicators.......................................................................................1-14

Configuration.................................................................................... 1-15

Dip Switches...............................................................................................1-15

Default Factory Settings ...........................................................................1-15

Baud Rate Selection ..................................................................................1-16

ii Table of Contents

2325 Vehicle Printer Reference Guide E-EQ-2325VPRG-A-ARC

Illustrations

Figure 1-1 2325 In the Cradle of the Vehicle Printer........................................................... 1-1

Figure 1-2 Proper Connection of the Vehicle Cable ............................................................ 1-5

Figure 1-3 Three Connectors on Vehicle Printer ................................................................. 1-7

Figure 1-4 RS-232 Pinouts................................................................................................... 1-7

Figure 1-5 9-Pin RS-232 Description................................................................................... 1-8

Figure 1-6 Printer Panel Buttons........................................................................................ 1-11

Figure 1-7 Printer Panel Indicators .................................................................................... 1-13

Figure 1-8 Cradle Indicators .............................................................................................. 1-14

E-EQ-2325VPRG-A-ARC 2325 Vehicle Printer Reference Guide

Chapter 1

Introduction and Specifications

Introduction

Refer to the 2325 Vehicle Printer Operator’s Guide

(LXE DocID 2325A137OPGD) for operation and

installation information

The portable LXE™ 2325 Vehicle Printer, for use with LXE’s 2325

handheld computers, combines a rugged dot matrix printer with the

charging and storage functions of a storage cradle for the handheld

computer. The printer has an integrated vehicle power supply, integrated

paper tray and 2325 cradle. The unit prints a full 80 columns width at

180 characters per second.

Figure 1-1 2325 In the Cradle of the Vehicle Printer

The built-in computer cradle in the printer safely holds the 2325

handheld computer for both data printing and computer storage and

charges the 2325 battery. The printer operates as a true portable system

Note: Refer to the next sections for information on the 12V internal

battery and connecting vehicle power to the printer.

1-2 Introduction

2325 Vehicle Printer Reference Guide E-EQ-2325VPRG-A-ARC

About This Guide

Refer to the LXE 2325 Operator’s Guide (LXE DocID

2325A136OPGD) for instructions when operating a 2325 in the 2325

Vehicle Printer.

This guide presents information on the printer, paper, ribbons, printer

settings, indicator lights, charging the battery, care and maintenance,

programming the printer, and supported character sets.

This product contains a Small Sealed Lead-Acid (SSLA) battery.

This battery must be recycled. Disposal of this battery must be in

accordance with local, state, and federal regulations. The State of

Florida “Land Ban” applies to this battery. In Canada, disposal must

be in compliance with Canadian environmental protection laws. For

further information call LXE at 770-449-0154.

Document Conventions

The following conventions are used in this document:

• Bold type and CAPITAL LETTERS are used to identify commands.

• Italics are used for parameters.

• Bullets indicate:

- action items

- lists of alternatives

- lists of required steps that are not necessarily sequential.

• Sequential lists (e.g., those that describe step-by-step procedures)

appear as numbered lists.

Connect Power Supplies 1-3

E-EQ-2325VPRG-A-ARC 2325 Vehicle Printer Reference Guide

Connect Power Supplies

Physical Installation

The printer is designed to be fully portable. The main criteria for

installation/operation is to ensure that the unit is level so that the

printhead moves from side to side without having to be pulled “uphill”

by the carriage motors.

When mounted within the cab of a vehicle or anywhere else within the

vehicle, care should be taken to ensure that the unit does not move

during acceleration, braking or traversing rough roads. This may be

accomplished by use of straps or a retaining box around the printer.

Excessive vibration and shock can be minimized by using dense foam

padding under and/or around the unit.

It would not be advisable to place the printer in any location where it

could become a lethal projectile in the event of an accident.

Internal 12V Battery Instruction

Important

The LXE 2325 Vehicle Printer is shipped with a disconnected battery.

This method preserves the overall life of the battery as well as maintains

the original charge. Make sure to connect the battery before using the

printer. The battery is a 12V DC lead acid gel battery, Model PP12V2

manufactured by GS Battery-Canada.

Connect the

Battery

1. Open and remove the printer cover (see section titled “Opening the

Printer”).

2. Open the printer mechanism using the release lever (see section

titled “Paper, Loading Paper”).

3. Flip up the levers on both tractor feed assemblies (see section titled

“Paper, Loading Paper”).

4. Using a Phillips screwdriver, loosen (DO NOT REMOVE) the two

screws on each end of the battery hold down bar (battery bar screws

1-4 Connect Power Supplies

2325 Vehicle Printer Reference Guide E-EQ-2325VPRG-A-ARC

can be seen through the two holes in the printer mechanism base

plate). The battery bar is located directly below the printer

mechanism base plate.

5. Slide the battery out from its compartment to access the battery

terminals (to slide the battery out, tilt the printer while slightly

lifting on the battery).

6. Remove tape on wires as well as the red tape on the terminals and

connect the red wire to the red terminal on the battery and the black

wire to the black terminal - make sure the wires stay underneath the

hold down bar.

7. Slide the battery (lettering side down) underneath the hold down bar

by tilting it forward.

8. Tighten the two screws. Hint: Load the paper in the printer after

this step.

9. Flip down the two levers on the tractor feed assemblies.

10. Lower the printer mechanism.

11. Close the cover.

The printer is now ready to use.

Battery Life

In order to maintain the life of the 12V gel battery in the printer, one of

two options must be followed:

1. The printer is turned off and left plugged into a charger when not in

use.

2. The battery is disconnected if the printer is to be unused for more

than four weeks.

Connect Power Supplies 1-5

E-EQ-2325VPRG-A-ARC 2325 Vehicle Printer Reference Guide

Vehicle to Battery Connection

Important This equipment is designed for Vehicle Use Only. Any other use is

at the owner’s risk and responsibility.

Equipment is designed to use 10 to 30 volt DC power source only.

The printer should receive a full charge on a daily basis. The battery is

fully charged when the green LED turns off.

The printer is designed for use with any DC power source within the

range of 10 V to 30 V. When connected to a power source that falls

within this range and can source the proper amount of current, the

printer battery will be properly charged and will maintain its charge

under normal usage.

It is recommended that the vehicle cable be connected to an unswitched

outlet on the vehicle’s fuse box, or directly to the vehicle battery. This

connection method reduces the chance of interference from the vehicle’s

charging system and prolongs the life of the printer’s internal 12V DC

Lead acid gel battery.

Figure 1-2 Proper Connection of the Vehicle Cable

The printer chassis (green wire) is isolated from the printer electronic

ground. Therefore, the printer can be used with positive or negative

ground vehicle systems.

1-6 Connect Power Supplies

2325 Vehicle Printer Reference Guide E-EQ-2325VPRG-A-ARC

When the printer is connected to an unswitched outlet on the fuse box

the printer will always receive a charge from the vehicle battery. If the

unit is left turned on for extended periods of time the unit could drain the

vehicle battery.

If the printer is connected to a switched outlet on the fuse box the printer

will only charge when the vehicle is on. This will eliminate the problem

of draining the vehicle battery; however it may place additional load on

the internal battery of the printer should the vehicle be run for short

periods. The printer should receive a full charge on a daily basis. The

unit is fully charged when the green CHARGING indicator light turns

off. The printer must be connected to an external source (vehicle or

external power supply) to ensure that the battery is properly charged.

Fuse Replacement

The unit uses a 250V, 3A Fast Blow, high current interrupting rating

fuse that is externally accessible and user replaceable. Should it need

replacement, replace with same size, rating and type of fuse -- Littelfuse

part number 312-003.

Internal Fuse Replacement:

The internal fuses F1 and F2 are rated at

F1: 250V 4 Amps Slow Blow

F2: 250V 3 Amps Fast Blow

Caution:

For continued protection against risk of fire, replace

only with the same type and rating of fuse.

Connectors 1-7

E-EQ-2325VPRG-A-ARC 2325 Vehicle Printer Reference Guide

Connectors

Figure 1-3 Three Connectors on Vehicle Printer

1 Power

2 RS-232 (Optional) Connector

3 Internal Modem (Optional) Connector

(RJ-45)

Optional RS-232 Connector

RS-232 Connection is made through an RS-232 Connector. The

connector is an industry-standard RS-232. The connector includes a

PC/AT standard 9-pin “D” male connector with pin 9 capable of

supplying 5 VDC at 200mA (max) for an external barcode scanner.

Pin 1 Pin 5

Pin 6 Pin 9

Figure 1-4 RS-232 Pinouts

1-8 Connectors

2325 Vehicle Printer Reference Guide E-EQ-2325VPRG-A-ARC

PIN SIGNAL DESCRIPTION

1 DCD Data Carrier Detect - Input

2 RXD Receive Data - Input

3 TXD Transmit Data - Output

4 DTR Data Terminal Ready - Output

5 GND Signal/Power Ground

6 DSR Data Set Ready - Input

7 RTS Request to Send - Input

8 CTS Clear To Send - Input

9 RI Ring Indicator - Input (Default)

Figure 1-5 9-Pin RS-232 Description

Optional Internal Modem

Note: Chapter 4 “Software Controlled Universal Serial Switch

(SCUSS)” only applies when a modem board is installed in the

vehicle printer.

Plug one end of the telephone cord (four conductor flat cable) into the 6-

pin RJ-45 connector and the other end into an analog telephone wall

jack.

The modem supports the AT Command set with extensions and can

operate with industry standard communication software.

Specifications and Features 1-9

E-EQ-2325VPRG-A-ARC 2325 Vehicle Printer Reference Guide

Specifications and Features

LXE 2325 Reference guide

LXE 2325 Reference guide

Related papers

Other documents