Balboa Magna'flow Operating instructions

Magna'flow
Balboa
Brand
Balboa
Model
Magna'flow
Type
Operating instructions

This manual is also suitable for

Balboa Water Group Magna'flow Manifold Jet is a versatile and easy-to-install spa jet that offers a customizable and relaxing hydrotherapy experience. With its adjustable nozzle assembly and therapy options, you can tailor the water flow and intensity to your liking. The jet's sleek design and simple installation process make it a great addition to any spa, allowing you to enjoy a soothing massage in the comfort of your own home.

Balboa Water Group Magna'flow Manifold Jet is a versatile and easy-to-install spa jet that offers a customizable and relaxing hydrotherapy experience. With its adjustable nozzle assembly and therapy options, you can tailor the water flow and intensity to your liking. The jet's sleek design and simple installation process make it a great addition to any spa, allowing you to enjoy a soothing massage in the comfort of your own home.

MAGNA’FLOW MANIFOLD JET INSTRUCTIONS
The correct hole size for the Magna’flow Manifold jet is 2 5/8”.
Before drilling the hole(s) to install the jet(s), make sure mounting surface is flat. This will help assure the best seal. 1.
Drill one 2 5/8” hole for each jet. 2.
The gasket (#2) can be placed on the inside or outside surface. Make sure surface is smooth enough to seal. 3.
Before inserting the wall fitting (#3) thru the hole, apply silicone to threaded area of wall fitting only. This will help 4.
seal the wall fitting (#3) and jet (#1) together.
Tighten wall fitting (#3) into jet (#1) hand tight (10 FOOT POUNDS MAX ALLOWED) with gasket (#2) in place. The 5.
gasket (#2) and silicone will create a good seal.
After the jets are installed on spa, connect the plumbing. Be sure air line is connected to barb and water line is 6.
placed in socket. Use care when applying cement inside slip socket of the jets. If too much cement is used, it
may be pushed up inside jet housing causing poor jet performance.
Be sure air lines do not sag. If air lines sag, the jets may not aerate properly. 7.
Run spa for fifteen minutes to clear debris from water lines, then thread nozzle assembly (#4) into place using a 8.
9/16” nut driver. Make sure nozzle assembly is threaded snugly into place.
Slip adjustment handle (#5) through wall fitting (#3) lining up ribs on side of nozzle assembly (#4) with cut-outs at 9.
base of adjustment handle (#5). Press adjustment handle (#5) firmly into place. Clips must snap into place.
Insert therapy option into adjustment handle (#5). Pressing firmly to snap into place. To remove, pull on snout of 10.
eyeball (or flowpath spout).
Note: It may be easier to remove therapy option with pump running. Block outlet
with index finger and pull on snout of eyeball or flowpath spout.
Rotate adjustment handle (#5) 9011. ° to control flow of water.
CAUTION: DO NOT APPLY ANY SILICONE INSIDE THE JET. THIS WILL INTERFERE WITH
THE OPERATION OF THE JET.
88-4876, Rev. A June 1, 2009
#1 3/4” x 3/8” MANIFOLD
JET BODY 10-4570
#2 AFII GASKET 10-5847
#3 WALL FITTING 10-4801
#4 NOZZLE ASSEMBLY 10-4804
#5 ADJUSTMENT HANDLE 10-4802
OR SL ADJUSTMENT HANDLE 10-4702
#6 DUAL PORT PATHFLOW 10-4820
#7 EYEBALL 10-4503
#8 CAGE 10-4806
#9 SINGLE PORT PATHFLOW 16-4821
  • Page 1 1

Balboa Magna'flow Operating instructions

Magna'flow
Balboa
Brand
Balboa
Model
Magna'flow
Type
Operating instructions
This manual is also suitable for

Balboa Water Group Magna'flow Manifold Jet is a versatile and easy-to-install spa jet that offers a customizable and relaxing hydrotherapy experience. With its adjustable nozzle assembly and therapy options, you can tailor the water flow and intensity to your liking. The jet's sleek design and simple installation process make it a great addition to any spa, allowing you to enjoy a soothing massage in the comfort of your own home.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents