Zamel EXTA FREE RNK-04 Manual Instruction

Brand: Zamel

Model: EXTA FREE RNK-04

Category: Wall transmitters

Type: Manual Instruction

RZB-04 WIRELESS CONTROL SET

- LIGHTING, 2-CHANNEL MANUAL INSTRUCTION

ZAMEL Sp. z o.o.

ul. Zielona 27, 43-200 Pszczyna, Poland

tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04

www.zamelcet.com, e-mail: [email protected]

VER. 003_20.05.2011

APPEARANCE

FEATURES

TECHNICAL DATADESCRIPTION

●completesetofwirelesscontrol(4–chan-

nel button radio transmitter RNK-04 and

2-channelradioflushreceiverROP-02).

●2outputrelays(drycontacts230VAC),

●lighting, heating operation control, other

receiverscontrol,

●easyushinstallationØ60mm,

●5operationmodes:switchingon,switch-

ing off, monostable mode, bistable mode,

timemode(switchoffdelay),

●wideoperationrange(upto200m),

●operationisopticallysignalled,

●low current consumption, possibility of

constant operation,

●possibility of increasing operation range

by means of RTN-01 retransmitter.

Radio ush receivers are used both as

elements in mounting in ush and surface

installation cable boxes and as an actuator

built directly in lighting tting casings and

other receivers). ROP-02 enables operation

in5differentmodes(switchingon,switching

off, monostable mode, bistable mode, time

mode.

RNK-04 ROP-02

Input (supply) terminals: - L, N

Inputratedvoltage: 3 V DC (CR2032 battery) 230 V AC

Battery life: 3 ÷ 5 years -

Inputvoltagetolerance:

-15 ÷ +10 %

Nominal frequency:

50 / 60 Hz

Nominalpowerconsumption: - 0,39 W („stand-by” mode) / 0,69 W

operationmode1channel/1,09W

operationmode2channels

Number of operation modes: - 5

Numberofchannels: 4 2

Transmission: radio 868,32 MHz

Codingway: unidirectional

Coding:: addressing transmission

Maximum number of remote controls: - 32

Range: upto250mintheopenarea

Time adjustment: - 1sec÷18hours(every1sec)

Optic signalling of transmitter’s operation: LED red diode

Input terminals: - IN1, IN2

Transmitter’s input (supply) terminals: - OUT1,OUT2(voltagecontacts)

Relay contact parameters: - 2NO 5A / 250V AC AC1 1250 VA

Number of terminal clamps: - 6

Section of connecting cables: - up to 2,5 mm2

Ambient temperature range: -10 ÷ +55 oC

Operating position: free

Casing mounting:

wall plugs, double-sided adhesive tape

installationcableboxØ60mm

Casing protection degree: IP20 (EN 60529)

Protectionlevel: III II

Overvoltagecategory: - II

Pollution degree: - 2

Surgevoltage: - 1 kV (EN 61000-4-5)

Dimensions: 90 x 80 x 11,5 mm 47,5 x 47,5 x 20 mm

Weight: 0,038 kg 0,039 kg

Reference standard: ETSI EN 300 220-1,

ETSI EN 300 220-2

EN 60669, EN 60950,

EN 61000

Opticsignallingofreceiver’soperation

Programmingpush-button

Input terminals (IN1, IN2)

Output terminals (OUT1, OUT2)

Input (supply) terminals (L, N)

Optic signalling

of transmitter’s operation

Push-buttons

The device is designed for

single-phase installation and

must be installed in accord-

ance with standards valid in

a particular country. The de-

vice should be connected

according to the details in-

cluded in this operating manual. Installation,

connectionandcontrolshouldbecarriedoutby

aqualiedelectricianstaff,whoactinaccord-

ance with the service manual and the device

functions.

Incaseofcasingdismantlinganelectricshock

mayoccur,andtheguaranteeislostthen.Be-

foreinstallationmakesuretheconnectionca-

blesarenotundervoltage.Thecruciformhead

screwdriver3,5mmshouldbeusedtoinstalthe

device. Improper transport, storage, and use

of the device inuence its wrong functioning.

 It is not advisableto instalthe device in the

followingcases:ifanydevicepartismissingor

thedeviceisdamagedordeformed.Incaseof

improperfunctioningofthedevicecontactthe

producer.

CAUTION!

The symbol means selective

collecting of electrical and electronic

equipment.

It is forbidden to put the used

equipment together with other waste.

WARRANTY CARD

Thereis24monthsguaranteeontheproduct

1. ZAMELprovidesatwo-yearwarrantyforitsproducts.

2. TheZAMELwarrantydoesnotcover:a)mechanicaldefects resultingfromtransport,loading/unloadingorothercircumstances

b)defectsresultingfromincorrectinstallationoroperationofZAMELproducts;c)defectsresultingfromanychangesmadebyCUS-

TOMERSorthirdparties,toproductssoldorequipmentnecessaryforthecorrectoperationofproductssold;d)defectsresulting

fromforcemajeureorotheraleatoryeventsforwhichZAMELisnotliable;e)powersupply(batteries)tobeequippedwithadevice

inthemomentofsale(iftheyappear);

3. AllcomplaintsinrelationtothewarrantymustbeprovidedbytheCUSTOMERinwritingtotheretailerafterdiscoveringadefect.;

4. ZAMELwillreviewcomplaintsinaccordancewithexistingregulations.;

5. Thewayacomplaintissettled,e.g.replacementoftheproduct,repairorrefund,islefttothediscretionofZAMEL.

6. Guaranteedoes not exclude, does not limit, nor does it suspend therightsofthe PURCHASER resulting from the discrepancy

betweenthegoodsandthecontract.

Salesman stamp and signature, date of sale

CONNECTION

APPLICATION

CAPACITY

750W

250W

500W

375W

ROP-02 MOUNTING

1.Disconnectpowersupplybythephasefuse,

thecircuit-breakerortheswitch-disconnector

combinedtothepropercircuit.

2. Check if there is no voltage on connec-

tion cables by means of a special measure

equipment.

3.Connectthecableswiththeterminalsinac-

cordancewiththeinstallingdiagram.

4.InstallROP-02deviceininstallationcablebox.

5.Switchonthepowersupplyfromthemains.

RNK-04 FUNCTIONING, MOUNTING

Bypressingthebutton,thetransmittersends

asignalwith868,32MHzfrequencywhichcon-

trolsEXTAFREEreceivers.Device program-

ming procedure (adding a transmitter to

a receiver’s memory) is described in par-

ticular EXTA FREE manual instructions.

Thedevicerange(upto250mdependingon

areceiver)canbeincreasedbymeansofare-

transmitterorfewRTN-01retransmitters.The

devicecanbemountedinanyplacebymeans

ofdouble-sided adhesive tape orwall plugs

5 x (3 x 30) mm.

Mountingbymeansofwallplugs:

1.Removethebutton- todoitpressthebut-

ton on one side, and on the other side put

ascrewdriverintoaslotandliftupthebutton.

2. Find a place on the wall to mount the

transmitter, make two holes corresponding

mountingholesfromthetransmitter’sbase.

3.Setwallplugsintheholes.

4.Fixthebasebymeansofscrewingscrews

intowallplugs.

5.Placethebuttonagain.

BATTERY CHANGE

Battery discharge status is signalled by

several LED red diode ashes during

transmission time.

1.Removethebutton(mounting-point1).

2. By means of a screwdriver lever up the

printed-circuit board releasing the bottom

latchandremoveitfromthebase.

3.Removethebatteryfromthelatch.

4.Mountanewbattery.Watchbatterypolari-

sationmarkedonthelatch.Wrongbattery

mountingmaycausedevicedamage.

5.Puttheremovedprinted-circuitboardback

inthebase.

6.Putbackthebutton.

CAUTION: While changing the battery,

it is suggested to press any of the buttons

for about 5 seconds before putting it into

a latch. Next press transmission button

several times to check its operation. If the

transmitter does not work properly repeat

the battery change procedure.

2-channelradioushreceiverROP-02

operatesasareceiverof8-channelremote

controllerP-256/8andof4-channelbutton

radiotransmitterRNK-04(lightsources

switchon/switchoffcontrol).Theabove

mentioned transmitters can also control

operationofradiolightingswitchRWL-01

and remote control socket RWG-01.

TheZAMELcompanydevices

whicharecharacterised

withthissigncancooperate

witheachother.

VER. 003_20.05.2011

ROP-02 OPERATION

ROP-02canoperateinvemodesforeverychannel:

MONOSTABLE

the relay operates only

while pressing transmit-

ter’spush-button.

BISTABLE

(one push-button) the

device changes relay

statuscyclicallyalways

after pressing the same push-

button.

SWITCH ON

the device switches on

afterpressingthepush-

button.

SWITCH OFF

the device switches off

afterpressingthepush-

button.

TIME

the device switches

off according to the

adjusted time (tp),

butitmaybeswitchedoffbefore

adjusted time nishes. Default

settings - 15 seconds.

CAUTION! Adjusted time can

not be deleted.

RADIO TRANSMITTERS PROGRAMMING - CHANNEL 1

TIME PROGRAMMING

RADIO TRANSMITTERS PROGRAMMING - CHANNEL 2

RADIO TRANSMITTERS DELETION

COOPERATION AND OPERATING RANGE

Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01

RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m

RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m

P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m

P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m

RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m

RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m

RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m

RNL-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m

RTN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m

RCR-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m

RTI-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m

RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m

*-1-channeltransmittersdonotcooperatewithrollerblindcontrollers.

CAUTION: The given range concerns open area - an ideal condition without any natural or articial obstacles. If there are some obstacles between a transmitter and a receiver,

it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100% ,

glass: from 10 to 20 %, Over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have

also a negative inuence on the range.

MONOSTABLE mode:

BISTABLE mode:

SWITCH ON/SWITCH OFFmode(twopush-buttons):

TIMEmode(onepush-button):

AnexemplaryprogrammingprocedurewiththeuseofP-257/2remotecontroller.TheprocedurefortherestofradioEXTAFREEtransmitters

is analogous. CAUTION: Every transmitter can cooperate with ROP-02 in a different mode, depending on how they were added to

the device. One transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode.

Press transmitter’s

push-buttonfor

a longer time.

Pressthetransmitter’spush-button

for a longer time. LED red diode

switcheson(rstsignalpulsates,

nextthesignalisconstant).

PressPROGpush-buttonofROP-01

deviceandthenreleaseit.LEDreddiode

switcheson(rstsignalpulsates,

nextthesignalisconstant).

Pressandreleasetransmitter’srst

push-button.LEDreddiodeswitcheson

(rstsignalpulsates,

nextthesignalisconstant).

Releasetransmitter’spush-

button.LEDreddiodeswitches

on(rstsignalpulsates,next

thesignalisconstant).

Release transmitter’s

push-button.LEDreddiodeswitches

on(thesignalpulsates),nexttheLED

reddiodeswitchesoff-itmeansthe

TRANSMITTER IS ADDED.

Pressandreleasethesametransmitter’s

push-buton.LEDreddiodeswitcheson

(signalpulsates)andthenswitchesoff-

THE TRANSMITTER IS ADDED.

Pressandreleasethesecondtransmitter’s

push-button.LEDreddiodeswitcheson

(thesignalpulsates)andnextitswitches

off - THE TRANSMITTER IS ADDED.

Pressthesametransmitter’spush-

-button and release it. LED red

diodeswitcheson(thesignalpulsa-

tes)andnextitswitchesoff-THE

TRANSMITTER IS ADDED.

PressPROGpush-buttonofROP-02device

foralongertimeuntilLEDreddiodeswitcheson

(constantsignal).NextreleasePROGpush-button.

PressPROGpush-buttonofROP-02device

for a longer time until LED red diode

switcheson(constantsignal).

NextreleasePROGpush-button.

PressPROGpush-buttonofROP-02device

for a longer time until LED red diode

switcheson(constantsignal).

NextreleasePROGpush-button.

PressPROGpush-buttonofROP-02device

for a longer time till LED red diode

switcheson(constantsignal).

NextreleasePROGpush-button.

CAUTION: Forthemonostablemode,pressthebuttonontheremotebeforepressingPROGpush-button.

Wait again (for about 5 seconds) till

LEDreddiodeswitcheson(rstsignal

pulsates,nextthesignalisconstant).

Waitagain-thirdtime(forabout5

seconds) till LED red diode

switcheson(rstsignalpulsates,

nextthesignalisconstant).

Aftertheadjustedtimeisnished(the

numberofLEDreddiodeashes)press

PROGpush-buttonandthenreleaseit-

TIME IS ADDED.

Aftertheadjustedtimeisnished

(thenumberofLEDreddiodeashes)

pressPROGpush-buttonandthen

release it - TIME IS ADDED.

PressPROGpush-buttonofROP-02deviceand

thenreleaseit.LEDreddiodeswitchesoffand

thenswitcheson(signalpulsates).EveryLED

diode pulse equals 1 second.

for

CHANNEL 1

for

CHANNEL 2

PressPROGpush-buttonofROP-02device

andthenreleaseit.LEDreddiodeswitchesoff

andthenswitcheson(signalpulsates).Every

LED diode pulse equals 1 second.

Maximumtimeis18hours.

PressPROGpush-buttonofROP-02deviceforalongertimetillLEDreddiodeswitcheson

(constantsignal).NextreleasePROGpush-button.Wait(forabout5seconds)tillLEDred

diodeswitcheson(rstsignalpulsates,nextthesignalisconstant).

PressPROGpush-buttonofROP-02deviceforalongertimeuntilLEDreddiodeswitches

on(constantsignal).NextreleasePROGpush-button.Wait(forabout5seconds)tillLEDred

diodeswitcheson(rstsignalpulsates,nextthesignalisconstant).

ChooseoneofROP-02veoperationmodes

andprogrammethedeviceinthesamewayas

forchannel1.

PressPROGpush-buttonofROP-02device

for a longer time.

After5secondsLEDreddiodeswitcheson

(signalpulsates)andthenitswitchesoff.

Releasethepush-buttoninROP-02-

MEMORY IS DELETED.

1s 2s ns

Zamel EXTA FREE RNK-04 Manual Instruction

Brand: Zamel

Model: EXTA FREE RNK-04

Category: Wall transmitters

Type: Manual Instruction

Download PDF

report

Zamel EXTA FREE RNK-04 Manual Instruction

Zamel EXTA FREE RNK-04 Manual Instruction

Related papers

Other documents