Jandy AquaLink RS All Button Quick Review Card

Brand: Jandy

Model: AquaLink RS All Button

Type: Quick Review Card

AquaLink® RS All Button Quick Review Card

Basic Operation: The AquaLink® RS All Button Indoor Controller can turn your pool/spa/landscape equipment on and off two ways:

First, you can press the button of the equipment you want to turn on. When the LED above the button is illuminated, the equipment is on (with

the exception of the heater buttons). When the LED above a button ashes, the equipment is being protected by a built-in safety delay.

Second, you can program the equipment to turn on and off at specic times.

Owners Manual may be downloaded online @ www.jandy.com

For Technical Support call 707.776.8200 ext.260

6000 Condor Dr., Moorpark, CA, USA 93021 • 707.776.8200 • FAX 707.763.7785

Filter Pump Button

Spa Pump Button

Equipment Labels

Display

Display Hold/ Release

Heater Button

Auxiliary Buttons

Turns on the lter pump and starts

water circulation.

Turns on the lter pump and

switches water circulation from pool

to spa.

Indicates generic “AUX” labels. Cus-

tom labels can be added for each

“AUX” from the label pack.

Rotates between messages indicat-

ing time/date/temperature and status

of equipment.

Stops or starts the display rotating

through messages (e.g. time, date,

temperature).

Turns auxiliary functions on and off. If

LED is lit, function is on.

Turns heaters on and off. If LED is

green, heater is enabled. If LED is red,

heater is ring.

Basic Programming: To set a particular piece of equipment to turn on and off at a predetermined time, press the MENU button, press

the forward arrow button to scroll to the PROGRAM menu, press ENTER, and then press the button for the equipment that you want to

program. The Controller Display will ask you to enter the day. Use the arrow buttons to select the day and press ENTER. The display will

now ask you for the starting and ending times. Repeat this process for each piece of equipment that you wish to program. You may enter as

many programs as needed for each piece of equipment.

Set the Time: First press the MENU button, then use the forward arrow button to scroll to SET TIME and press ENTER. Scroll to the correct

year,month and day, pressing ENTER for each. Scroll to the correct hour and minute and press ENTER.

Label Auxiliary Functions: Press the MENU button, press the backward arrow button to scroll to SYSTEM SETUP and press ENTER. At

the LABEL AUX menu, press ENTER, and select the AUX button above to label. Scroll to the desired function in the LABEL AUX menu and

press ENTER. Repeat for all functions.

Note 1: The labels “TIMED AUX”, “AIR BLOWER” and “FILL LINE” are 30 minute timed cycles.

Note 2: If DIP switches 1,2, or 3 are on, Auxiliaries 1, 2 and 3 are labeled CLEANER, LOW SPEED and SPILLOVER respectively and

cannot be relabeled.

Set the Temperature: Press the MENU button, then use the forward arrow button to scroll to SET TEMP and press ENTER. Use the arrow

buttons to move between pool and spa temperature, then press ENTER. Use the arrow buttons to raise or lower the temperature, then

press ENTER.

AquaLink® RS All Button Programming & System Defaults

Default Temperature Default Remote Settings Default Freeze Protection Settings

Default Pool Temp. 80°F

Default Spa Temp. 102°F

Default Temp. 1* 80°F

Default Temp. 2* 60°F

*Pool only / Spa only systems

Button 1 - Spa (Filter Pump)*

Button 2 - Spa Heater (Temp 1)*

Button 3 - AUX 1

Button 4 - AUX 2

*Pool/Spa combination systems

Filter Pump: Freeze Protection ON.

All other Equipment: Freeze Protection OFF

NOTE: If you selected Spa to be freeze protected, water

circulation will switch between pool and spa every 30

minutes during freezing pool and spa every 30 minutes

during freezing conditions once freeze mode is active.

7059 Rev. C

Jandy AquaLink RS All Button Quick Review Card

Jandy AquaLink RS All Button Quick Review Card

Jandy AquaLink RS All Button Quick Review Card

Related papers

Other documents