TP-LINK RE200 Quick Installation Manual

Category
Networking
Type
Quick Installation Manual

TP-LINK RE200 is a wireless range extender that eliminates Wi-Fi dead zones by extending the coverage of your existing network. It features two easy setup options, either via a web browser or using WPS (Wi-Fi Protected Setup). It can extend both 2.4GHz and 5GHz Wi-Fi bands, providing a fast and stable connection for devices like smartphones, tablets, and laptops. Additionally, it comes with an Ethernet port, allowing you to connect wired devices like gaming consoles or smart TVs to your wireless network.

TP-LINK RE200 is a wireless range extender that eliminates Wi-Fi dead zones by extending the coverage of your existing network. It features two easy setup options, either via a web browser or using WPS (Wi-Fi Protected Setup). It can extend both 2.4GHz and 5GHz Wi-Fi bands, providing a fast and stable connection for devices like smartphones, tablets, and laptops. Additionally, it comes with an Ethernet port, allowing you to connect wired devices like gaming consoles or smart TVs to your wireless network.

LEDs
7106505500 REV1.0.3
2.4G and 5G
Red – During boot up, reset, or weak wireless signal.
Green – Strong wireless signal.
OFF The extender is not connected to 2.4GHz or
5GHz Wi-Fi bands of your router.
Wireless Signal
ON The wireless is enabled.
OFF The wireless is disabled.
Power
ON The extender is powered on.
Ethernet
ON – A device is connected via the Ethernet port.
Blinking – The Ethernet port is transmitting data.
OFF – No device is connected via the Ethernet port.
Exit
Next
Choose Region Wireless Settings Review SettingsStart
Please click Next to set up the Range Extender or click Exit to go to the Device Management Page.
Main Router/AP WiFi Network Name(SSID):
Exit
Next
Wi-Fi Network Name_2.4GHz:
Wi-Fi Network Name_5GHz:
Connection Status:
N/A
N/A
Disconnected
Choose Region Wireless Settings Review SettingsStart
Quick
Installation
Guide
AC750 WiFi Range Extender
RE200
Two easy setup options:
Option 1: Using a Web Browser
Option 2: Using WPS (Wi-Fi Protected Setup)
Disconnect the Ethernet (wired) connection to
your computer. Click the Wi-Fi icon on the
taskbar and connect to the Extender's network
(e.g. TP-LINK_Extender_XXGHz). No password is
required to connect the rst time.
4
A. On the Start screen, click Next.
D. Enter your router’s Wi-Fi password and
either choose Copy from Main Router or
Customize to create a name for the 2.4GHz
extended network, then click Next.
E. Repeat step C and D to extend the 5GHz wireless
network.
F. Verify your Wireless Settings and click Finish.
Both 2.4G and 5G LEDs should turn on.
B. Choose your region from the Region drop-down
list and click Next.
Note: Per FCC regulations, all Wi-Fi products marketed in the
U.S. are xed to the U.S. region only.
C. Select your router's 2.4GHz wireless network
name (SSID), or select Skip to skip this band and
click Next. If the SSID is hidden, select Set SSID
and MAC manually.
Follow the Quick Setup Wizard to congure the extender.
3
Launch a web browser and type
http://tplinkrepeater.net in the address eld.
Use admin (all lowercase) for both Username
and Password to log in.
http://tplinkrepeater.net
admin
admin
Username:
Password:
Login
Cancel
Login
Congure
RESETThis button resets the extender to its
factory default settings.
ETHERNET port – Used to connect an
Ethernet-enabled device to the wireless
network.
RESET
ETHERNET
RESET
ETHERNET port
1
Plug the extender into an electrical outlet
near your router, and wait until the Wireless
LED is lit and solid green.
1
OPTION
Using a Web Browser
Power On
Ideal Range Extender Placement
5Relocate
2Connect
Signal MAC Channel Security
00-0A-EB-74-06-06 1 WPA-PSK
0C-72-2C-B3-A5-2C 1 WPA-PSK
Available Wireless Networks (2.4GHz): 24
Choose SSID
TP-LINK_2.4GHz_XXX
TP-LINK_XXX
Back
Next
Choose Region Wireless Settings Review SettingsStart
Set SSID and MAC Manually
Skip (I don’t want to use this band)
TP-LINK_2.4GHz_XXX
00-0A-EB-74-06-06
Most Secure(WPA-PSK/WPA2-PSK)
123456789
Back
Next
TP-LINK_2.4GHz_XXX_EXT
Choose Region Wireless Settings Review Settings
Start
Main Router/AP Network (2.4GHz)
Main Router/AP WiFi Network Name(SSID):
Main Router/AP MAC Address(BSSID):
WiFi Security Option:
Fill in the WiFi Password of your Main
Router/AP:
Range Extender Network (XXGHz)
Range Extender WiFi Network Name(SSID): Copy from Main Router/AP TP-LINK_2.4GHz_XXX
Customize
TP-LINK_5GHz_XXX
00-0A-EB-74-06-06
Most Secure(WPA-PSK/WPA2-PSK)
123456789
Back
Next
TP-LINK_5GHz_XXX_EXT
Choose Region Wireless Settings Review SettingsStart
Main Router/AP Network (5GHz)
Main Router/AP WiFi Network Name(SSID):
Main Router/AP MAC Address(BSSID):
WiFi Security Option:
Fill in the WiFi Password of your Main
Router/AP:
Range Extender Network (XXGHz)
Range Extender WiFi Network Name(SSID): Copy from Main Router/AP TP-LINK_5GHz_XXX
Customize
Wireless Setting
Main Router/AP WiFi Network Name (2.4GHz):
Main Router/AP WiFi Network Name (5GHz):
Range Extender WiFi Network Name (2.4GHz):
WiFi Security Option:
WiFi Password:
Range Extender WiFi Network Name (5GHz):
WiFi Security Option:
WiFi Password:
TP-LINK_2.4GHz_XXX
TP-LINK_5GHz_XXX
TP-LINK_2.4GHz_XXX_EXT
Most Secure (WPA/WPA2-PSK)
123456789
TP-LINK_5GHz_XXX_EXT
Most Secure (WPA/WPA2-PSK)
123456789
Choose Region Wireless Settings Review SettingsStart
Back
Finish
Export Settings
Both 2.4GHz and 5GHz extended networks share the same Wi-Fi password as your main network, but
may have dierent wireless network names if you customize the names during the conguration.
Region: Please Select Your Region
Please select your own region to prevent illegal usage against the local law.
Connection are available
Not connected
Wireless Network Connection
Connect automatically Connect
TP-LINK_Extender_XXGHz
Main Network Extended Network
5G
2.4G
A. Plug the extender into an electrical outlet
about halfway between your router and
the Wi-Fi dead zone.
B. Wait about 1 minute until the
corresponding LEDs ( 2.4G and 5G ) are lit
and stay solid.
Solid green Good connection
Too far away from the router
No connection
Solid red
O
Blinking – WPS connection is in process.
ON WPS connection is successful.
OFF The extender is not connected to
your router by WPS.
RE
Smart TV Game Console Desktop
Ethernet Connection
Router
Refer to Step 5 of Option 1 to relocate your
Range Extender.
Entertainment Adapter
Troubleshooting and Support
The Range Extender can be used as a wireless
adapter to connect any Ethernet-enabled device,
such as a Blu-ray player, game console, DVR, or smart
TV, to your wireless network.
First, connect the extender to your Wi-Fi network by
following the instructions in Option 1 or Option 2,
then connect an Ethernet-enabled device to the
extender using an Ethernet cable as shown in the
diagram on the right.
My router has no WPS button, how do I connect
the extender?
Your router does not support WPS, please use Option
1 to set up the extender.
Why both 2.4G and 5G LEDs are still o after
completing Option 1?
You may have entered the incorrect Wi-Fi password
of your main network during the conguration.
Please log into the Extender's web-based interface
to check the password and try again.
If the 2.4G and 5G LEDs are still o, please reset the
extender and go through the conguration again.
What should I do when I cannot connect the
extender via WPS?
Some dual-band routers may be trouble
connecting to the extender via WPS. If you
experience connection issues, please congure
the extender using Option 1.
What should I do if I cannot access the
Extender's web interface?
Make sure your computer is connected to the
extended network.
Make sure your computer is set to obtain an
IP address automatically.
1
2
3How do I restore the extender to its factory
default settings?
With the extender powered on, use a pin to
press the Reset button until all the LEDs turn
on momentarily, then release the button.
5
4Technical Support
For detailed troubleshooting instructions, visit:
www.tp-link.com/en/support/faq
For all other technical support, please contact us at:
USA / Canada
Toll Free: +1 866 225 8139
E-mail: support.usa@tp-link.com (USA)
support.ca@tp-link.com (Canada)
Support Availability: 24 hours a day, 7 days a week
1
Plug the extender into an electrical outlet
near your router, and wait until the Wireless
LED is lit and solid green.
2
OPTION
Using WPS (Wi-Fi Protected Setup)
Power On
3Relocate
2Connect
Important: Please use Option 1 if your router does not support WPS.
Keep away from
Enjoy!
Enjoy!
Choose a location away from Bluetooth devices and other
household electronics, such as cordless phone, microwave,
and baby monitor, etc., to minimize signal interference.
Both 2.4GHz and 5GHz extended networks share the same SSID (network name) and password as your main network.
Ideal Range Extender Placement
Main Network Extended Network
5G
2.4G
A. Press the WPS button on your router and immediately press the RE button on your extender.
The corresponding LEDs ( 2.4G and 5G )
should turn on and stay solid after about 1
minute, indicating that WPS connection is
successful.
If not, please use Option 1.
1. For more information about using WPS on your router, please refer to the router manufacturer's user guide.
2. The WPS function in some routers may be disabled by default. If the WPS connection fails, please use Option 1.
B. If you are connecting the extender to a dual-band router, but only 2.4G or 5G LED is on, repeat step A
to connect the other band.
©2015 TP-LINK
  • Page 1 1
  • Page 2 2

TP-LINK RE200 Quick Installation Manual

Category
Networking
Type
Quick Installation Manual

TP-LINK RE200 is a wireless range extender that eliminates Wi-Fi dead zones by extending the coverage of your existing network. It features two easy setup options, either via a web browser or using WPS (Wi-Fi Protected Setup). It can extend both 2.4GHz and 5GHz Wi-Fi bands, providing a fast and stable connection for devices like smartphones, tablets, and laptops. Additionally, it comes with an Ethernet port, allowing you to connect wired devices like gaming consoles or smart TVs to your wireless network.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI