TP-LINK RE200 Quick Installation Manual
- Category
- Routers
- Type
- Quick Installation Manual
TP-LINK RE200 is a compact yet powerful Wi-Fi range extender that can boost the wireless signal of your existing router and eliminate dead zones in your home or office. With dual-band technology, the RE200 extends both 2.4GHz and 5GHz Wi-Fi signals, providing speeds of up to 750Mbps. It also features a built-in Ethernet port, allowing you to connect wired devices such as gaming consoles, smart TVs, and desktop computers to your Wi-Fi network.
TP-LINK RE200 is a compact yet powerful Wi-Fi range extender that can boost the wireless signal of your existing router and eliminate dead zones in your home or office. With dual-band technology, the RE200 extends both 2.4GHz and 5GHz Wi-Fi signals, providing speeds of up to 750Mbps. It also features a built-in Ethernet port, allowing you to connect wired devices such as gaming consoles, smart TVs, and desktop computers to your Wi-Fi network.
LED Explanation
RE200
Applicable Model:
Quick
Installation Guide (Power)
On: The extender is on.
O: The extender is off.
Quick Setup using your Web Browser
Method ONE
Enjoy! Both extended networks share the same Wi-Fi passwords as those of your host networks, but may have dierent wireless network names if you have
customized them during the configuration.
(ETHERNET)
On: A device is connected to the ETHERNET port,
but there is no activity.
Flashing: A device is connected to the ETHERNET
port, and is active.
O: No device is connected to the ETHERNET port.
2.4G/5G
Solid Green: The extender is connected to the
2.4GHz/5GHz wireless network of the router and
is in a good location.
Solid Red: The extender is connected to the
2.4GHz/5GHz wireless network of the router, but
is too away from it.
O: The extender isn’t connected to the router.
On: The extender’s wireless function is enabled.
O: The extender’s wireless function is disabled.
(Wireless Signal)
On: WPS connection is established.
Flashing: WPS connection is in progress.
O: No active connection.
(RE)
Method ONE Quick Setup using your Web Browser
Launch a web browser, type http://tplinkrepeater.net in
the address bar and use admin (all lowercase) for both
Username and Password to log in.
Configure
1 4 Select the WiFi Security Option of the host network and
enter the password. Either keep the default SSID or
customize it for the extended network. Then click Next.
5Verify your wireless settings and click Finish.
Corresponding LED(s) (2.4G/5G) should light up.
http://tplinkrepeater.net
admin
admin
Login
Go to Quick Setup Wizard to configure your extender.
2
Back
Next
TP-LINK_2.4GHz_XXX
00-0A-EB-74-06-06
Most Secure(WPA-PSK/WPA2-PSK)
123456789
Copy from Main Router/AP
Customize
Main Router/AP Network (2.4GHz)
Main Router/AP WiFi Network Name(SSID):
Main Router/AP MAC Address(BSSID):
WiFi Security Option:
Fill in the WiFi Password of your Main Router/AP:
Range Extender Network (2.4GHz)
Range Extender WiFi Network Name(SSID):
TP-LINK_2.4GHz_XXX_EXT
TP-LINK_2.4GHz_XXX
Wireless Settings
Review Settings
Start
3Select your router’s 2.4GHz/5GHz host network and
click Next.
If the login window does not pop up, please refer
to the FAQ > Q2.
If your router does not support 5GHz wireless
network, please click Skip to continue.
Signal MAC Channel Security
00-0A-EB-74-06-06 1 WPA-PSK
0A-72-2A-B3-A5-2C 1 WPA-PSK
Available Wireless Networks (2.4GHz): 24
Choose SSID
TP-LINK_2.4GHz_XXX
TP-LINK_XXX
√
Wireless Settings
Review Settings
Start
Next
Rescan
Back
Set SSID and MAC Manually
Skip (I don’t want to use this band)
3
Relocate
Ideal Extender PlacementRouter Clients
Extended Network
Host Network
Wait for the extender to reconnect and the 2.4G/5G LED should turn green. If
not, relocate it closer to the router to achieve better signal quality.
Plug in the extender halfway between your router and the Wi-Fi dead zone.
The location you choose must be within the range of your existing host
network.
1
2
4
1. Unplug the Ethernet cable from your computer (if any).
2. Click the Wireless Network Connection icon on your
taskbar.
3. Click the refresh icon and connect to the extender’s
network (e.g. TP-LINK_Extender_2.4GHz5GHz).
or
Connect to the Extender
For Windows Users
Connection are available
Not connected
Wireless Network Connection
Connect automatically Connect
TP-LINK_Extender_2.4GHz
√
10:31
1. Unplug the Ethernet cable from your Mac (if any).
2. Click the Wi-Fi icon in the top right corner of the
screen, and connect to the extender’s network
(e.g. TP-LINK_Extender_2.4GHz/5GHz).
For Mac OS X Users
Wi-Fi: On
Turn Wi-Fi Off
TP-LINK_Router
Join Other Network...
Create Network...
Open Network Preferences...
TP-LINK_Extender_2.4GHz
Plug your extender into a power
outlet near your Router/AP.
Power on
12
Wait until the and LEDs
light up.
7106506294 REV1.0.2
©2016 TP-LINK
Frequently Asked Questions (FAQ)
Q1. How to reset the extender?
A1. With the extender powered on, press the RESET button with a pin for 1 second. Wait
for 2 seconds until all the LEDs flash once.
A2. Log into the management page via your web browser, go to System Tools >
Factory Defaults and click Restore.
Q2. What should I do if I can not access the web management page of the extender?
A1. If your computer is wirelessly connected, make sure that you have connected to the
extender’s SSID.
If your computer is connected via an Ethernet cable, please make sure that the
connection is stable.
A2. Make sure your computer is set to obtain an IP address and DNS server address
automatically.
A3. Verify that http://tplinkrepeater.net is correctly entered in the web browser and
press Enter.
Both extended networks share the same network names (SSIDs) and passwords as those of your host networks.
Enjoy!
Entertainment Adapter
Ethernet connection
Smart TV
Game Console
Desktop
The extender can be used as a wireless adapter to connect any Ethernet-only device
such as a Blu-ray player, game console, DVR or smart TV to your Wi-Fi network.
First, connect the extender to your router referring to Method ONE or Method TWO.
Then connect your Ethernet-only device to the extender via an Ethernet cable.
WPS is an easier way to extend your host network. You are recommended to use this method if your host router has a WPS button.
The button might look like one of these: . Otherwise, please refer to Method ONE.
Method TWO Quick Setup using the WPS (RE) Button
Plug the extender into a power
outlet near your router.
Power on
2
1Press the WPS button on your router, and then press the button on your extender.
Connect
If you are connecting the extender to a dual-band router but only 2.4G or 5G LED is on, repeat Step 1 to
connect the other band.
For more information about using WPS on your router, please refer to the router manufacturer's user guide.
Some ISP gateways disable the WPS function by default. If the WPS connection fails, please refer to Method ONE.
Relocate
Router
Ideal Extender PlacementRouter Clients
Extended Network
Host Network
Wait for the extender to reconnect and the 2.4G/5G LED should turn green. If
not, relocate it closer to the router to achieve better signal quality.
Plug in the extender halfway between your router and the Wi-Fi dead zone.
The location you choose must be within the range of your existing host
network.
1
2
The LED should go from
ashing to solid, indicating that
WPS connection was successful,
and then it will go o in 2 minutes.
12
3
Wait until the and LEDs
light up.
-
1
-
2
TP-LINK RE200 Quick Installation Manual
- Category
- Routers
- Type
- Quick Installation Manual
TP-LINK RE200 is a compact yet powerful Wi-Fi range extender that can boost the wireless signal of your existing router and eliminate dead zones in your home or office. With dual-band technology, the RE200 extends both 2.4GHz and 5GHz Wi-Fi signals, providing speeds of up to 750Mbps. It also features a built-in Ethernet port, allowing you to connect wired devices such as gaming consoles, smart TVs, and desktop computers to your Wi-Fi network.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
TP-LINK RE210 Quick Installation Guide
-
TP-LINK RE200 Quick Installation Manual
-
TP-LINK RE210 AC750 WiFi Range Extender Owner's manual
-
TP-LINK RE450 Quick Installation Manual
-
-
-
TP-LINK RE350 Quick Installation Manual
-
-
TP-Link Technologies TE7RE450 User manual
-
TP-LINK RE205 User manual
