Extron FOX II R DP 4K User manual

Category
Network media converters
Type
User manual

This manual is also suitable for

1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications bef
ore connecting the
pr
oduct to the po
wer source.
FOX II T/R DP 4K • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the
Extron FOX II T/R DP 4K Fiber Optic Extenders.
WARNING: The FOX II T/R DP 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with
caution. Plug the attached dust caps into the optical transceivers when the ber cable is unplugged.
CLASS 1 LASER PRODUCT, see the FOX II T/R DP 4K User Guide, at www.extron.com.
AVERTISSEMENT : Le FOX II T/R DP 4K émet une lumière invisible en continu (conforme à la classe1) qui peut être dangereux
pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque
le câble bre optique est débranché.
Produit laser de classe1, voir le FOX II T/R DP 4K User Guide sur www.extron.com (en anglais).
Installation
FOX II DP 4K Transmitter Rear Panel
FOX II DP 4K Receiver Rear Panel
100-240V ~ -.-A MAX
50-60 Hz
DISPLAYPORT LOOP THRU
LR
RS-232
OPTICAL
Tx
RESET
LINK
LINK
Rx
RS-232 IR
ALARM
Tx Rx G1 2
LR
Tx Rx Tx RxG
AUDIO
INPUTS
AUDIO
RETURN OUT
REMOTE
OVER
FIBER
FOX T DP 4K
100-240V ~ -.-A MAX
50-60 Hz
DISPLAYPORT
LR
RS-232
OPTICAL
Tx
RESET
LINK
LINK
Rx
RS-232 IR
ALARM
Tx Rx G1 2
LR
Tx Rx Tx RxG
AUDIO
OUTPUTS
AUDIO
RETURN IN
REMOTE
OVER
FIBER
FOX R DP 4K
Step 1 — Mounting
Turn off or disconnect all equipment power sources
and mount the transmitter and receiver as required.
For mounting details and considerations, see the
FOX II T/R DP 4K User Guide at www.extron.com.
Step 2 — Input and Output Connections
a. Connect a DisplayPort
DISPLAYPORT LOOP THRU
video source to the
transmitter DisplayPort input connector.
b. If desired, connect a DisplayPort video display
to the transmitter Loop-Thru connector for a
local display.
c. Connect a DisplayPort video display to the receiver DisplayPort output connector.
DISPLAYPORT
d. Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector
LR
AUDIO
on the transmitter. See the drawing below step 2g to make connections on the captive screw connector.
e. Connect an audio output device to either or both the 3.5 mm mini jack or the Audio 5-pole captive screw connector
on the receiver. See the drawing below step 2g to make connections on the captive screw connector.
f. For optional returned audio, connect an audio output device to the Audio Return Out 5-pole captive screw
LR
AUDIO
RETURN OUT
LR
AUDIO
RETURN IN
connector on the transmitter. See the drawing below step 2g to make connections on the captive screw
connector.
g. For optional returned audio, connect an audio input device to the Audio Return In 5-pole captive screw
connector on the receiver. See the drawing below to make connections on the captive screw connector.
ATTENTION:
For unbalanced audio, connect the sleeves to the
ground contact. DO NOT connect the sleeves to the
negative (–) contacts.
Pour l’audio asymétrique, connectez les manchons au
contact au sol. Ne PAS connecter les manchons aux
contacts négatifs (–).
NOTE: For returned audio, above, and RS-232 and IR responses (from the receiver to the transmitter), on the next page, you
must install the receiver-Tx-to-transmitter-Rx cable in step 3b.
Unbalanced Stereo Output Balanced Stereo Output
Unbalanced Stereo Input
Balanced Stereo Input
Do not tin the wires!
Tip
No Ground Here
No Ground Here
Tip
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves
Tip
Sleeve
Sleeve
Tip
LR
2
FOX II T/R DP 4K • Setup Guide (Continued)
h. If you want the FOX II DP 4K units to pass serial or IR data or control signals, such as for serial
Rx TxGnd
Tx RxGnd
IR Device
RS-232 Device
RS-232 IR
Tx Rx Tx RxG
OVER
FIBER
control of a projector, connect the master device to the transmitter and the controlled device to
the receiver via the Over Fiber 5-pole captive screw connectors on both units.
i. For remote monitoring of the status of the Rx optical link on either the transmitter or
RS-232
ALARM
Tx Rx G
12
REMOTE
receiver, connect a locally constructed or obtained device to the two rightmost poles
of the Alarm and Remote RS-232 5-pole captive screw connector on that unit. The
unit shorts both poles together when no light is detected.
NOTE: The transmitter port reports the status of the link from the receiver.
The receiver port reports the status of the link from the transmitter.
j. For remote control of a unit and for loading rmware, connect a host device, such as a computer or control system, to either of the
following ports on the unit to be controlled:
Configuration port
— The front panel USB mini-B connector.
NOTE: Extron recommends performing firmware updates via the Configuration port only.
Remote RS-232 port
— The rear panel Remote RS-232 port, the 3 leftmost poles of this 5-pole captive screw connector.
RS-232
ALAR
M
Tx Rx G
12
REMOTE
The protocol for the Remote port is as follows:
9600 baud no parity 8 data bits
1 stop bit no ow control
Step 3 — Throughput Connections
Receiver
T
ransmitter
11
22
22
11
OPTICAL
Tx
LINK
LINK
Rx
OPTICAL
Tx
LINK
LINK
Rx
NOTE: See the two fiber cable connection drawing at right. You can connect the transmitter and receiver in one of
two ways:
One way (transmitter to receiver) only, perform step 3a.
Two way (transmitter to receiver and return), perform steps 3a and 3b.
a. Connect the ber between the Tx port on the transmitter and the Rx port on the receiver (
1
, at right).
NOTE: Ensure that the transmitter and connected receiver are the same transmission mode, singlemode (SM) or
multimode (MM) and that you use the correct SM or MM fiber cable to connect the devices.
b. If you want the receiver to return serial data (such as responses from a controlled device), IR data, or returned audio
to the transmitter, connect a cable between the Tx port on the receiver and Rx port on the transmitter (
2
).
Tx Link and Rx Link LEDs — When lit, the link is active (light is output [Tx] or received [Rx]).
NOTE: The Link LEDs indicate transmission of light only, not whether there is data encoded in the optical link.
3
Operation
After the receiver, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems are
encountered, verify that the cables are routed and connected properly and that the display device has a compatible resolution and refresh
rate. If problems persist, call the Extron S3 Sales & Technical Support Hotline. See the contact numbers on the last page of this guide for
the Extron ofce nearest you.
Indications
NOTE: The figure below right is of a receiver. A transmitter has similar indications.
Power ( ) LED — Indicates that power is applied to the unit.
CONFIG
SIGNAL
VIDEO AUDIO
HDCP
OUTPUT
RETURN IN
Video LEDs
Signal LED — Lights on both units when the unit detects an input video
signal.
HDCP LED — Lights on both units when the input signal is HDCP
encrypted.
Audio LEDs
Input LED (transmitter) — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the
audio signal level drops below the threshold for 10 seconds or longer.
Output LED (receiver) — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the
audio signal level drops below the threshold for 10 seconds or longer.
Return Out LED (transmitter) — Lights when analog audio is present on the transmitter Return Audio Output connector.
Return In LED (receiver) — Lights when analog audio is present on the receiver Return Audio Input connector.
EDID (Transmitter)
SELECT
EDID
EDID Select rotary switch — Set this switch to one of the positions shown in the table below to select the source of the EDID or
a specic resolution.
Position 0 — An EDID that has previously been captured from a connected display or manually imported via an SIS
command or the Product Conguration Software.
Position 1 — The EDID is selected via the Remote or USB port on the transmitter only, using an SIS command or the Extron Product
Conguration Software.
Position 2 — Use the EDID from the display connected to the receiver.
NOTE: EDID from the display connected to the receiver requires connection of both ber cables.
Position 3 — Use the EDID from the display
connected to the transmitter loop-through.
Positions 4 through E — Specify a resolution.
The table at right identies the resolutions
associated with the switch positions. All
resolutions are at 60 Hz with the exception of
3840x2160 (E), which is 30 Hz.
Position F — No EDID assigned.
Remote control
See the FOX II T/R DP 4K User Guide, available at www.extron.com, for details on operating and monitoring the transmitter and receiver
using either SIS commands or the Extron Product Conguration Software.
Pos. Source or resolution Pos. Resolution Pos. Resolution
0 User recorded EDID 6 1366x768 C 2048x2160
1 Selected via RS-232 7 1440x900 D 2560x1600
2 Display on Rx output 8 1680x1050 E* 3840x2160
3 Display on Tx loop-through 9 1920x1080 F N/A
4 1280x720 A 1920x1200
5 1280x800 B 2048x1536
* 30 Hz
4
68-2540-50 Rev. B
01 16
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
FOX II T/R DP 4K • Setup Guide (Continued)
Application Diagram
S
T
A
N
D
B
Y
C
L
A
S
S
2
W
IRIN
G
1
2
XPA 10
0
2
LEVE
L
1
1
2
1
2
LI
MI
TER/
PR
O
T
ECT
S
I
G
NAL
2
INPUTS
O
UTPUT
R
EM
O
TE
0
0
V
OL/M
U
TE
1
0V
5
0
mA
100
-24
0V
1.
3
A
,
5
0
-6
0
Hz
100-
24
0V ~ -
.-A MAX
50-60 Hz
DISPLAYPORT
L R
RS-232
OPT
ICAL
T
x
R
ES
ET
LINK
LINK
Rx
RS-232 IR
ALARM
Tx Rx G
1 2
L R
Tx Rx Tx RxG
AUDIO
OUTPUTS
AUDIO
RET
URN IN
REMOTE
OVER
FIBER
FOX R DP 4K
100-240V ~ -.-A MAX
50-60 Hz
DISPLAYPORT LOOP THRU
L R
RS-232
OPTICAL
Tx
RESET
LINK
LINK
Rx
RS-232 IR
ALARM
Tx Rx G 1 2
L R
Tx Rx
Tx
RxG
AUDIO
INPUTS
AUDIO
RETURN OUT
REMOTE
OVER
FIBER
FOX T DP 4K
POW
ER
12V
-
-
A MAX
G
Tx Rx
R
T
S
CT
S
C
OM 1
G
T
x
Rx
C
OM
2
V
C G
V
OL
RELAYS
1 2
C
1
2 3
4
G
DIGITAL I/O
PWR
OUT
=
6W
eBUS
+V
+S
-S
G
LAN
IPCP PRO 250
IR/S
S
G
MODE
L
80
Extron
Extron
H
e
lp
Syste
m
Off
Display
R
oom
Control
Off
Mute
Screen
Li
ghting
Decem
b
e
r 15, 20
1
3 - 7:5
8
AM
Audio
Control
Volume
Mute
Tuner
1 2
3
VCR
L
a
pto
p
PC
D
VD
D
o
c
C
a
m
Tuner
On
Channel
Las
t
Presets
M
ore
Presets
3
2
1
6
5
4
9
8
7
Ente
r
0
RS-232
Ethernet
Ethernet
Audio
4K DisplayPort
4K DisplayPort
4K DisplayPort
Extron
SI 28
Surface-mount
Speakers
Extron
XPA 10
02
Power
Amplier
4K Display
PC
Local
Monitor
Up to 30 km (18.75 miles)
Singlemode Fiber
SM Model
Audio
RS-232
Extron
FOX T DP 4K
Fiber Optic Transmitter
Extron
FOX R DP 4K
Fiber Optic Receiver
Extron
TLP Pro 72
0T
7" Table Top
TouchLink Pro
Touchpanel
TCP/IP
Network
Extron
IPCP Pro 250
IP Link Pro
Control Processor
1 / 1

Extron FOX II R DP 4K User manual

Category
Network media converters
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document