Ricatech RR1600 User manual

Page is loading ...

English

IMPORTANT SAFEGUARDS FOR AUDIO PRODUCTS

PLEASE READ CAREFULLY THE FOLLOWING IMPORTANT SAFEGUARDS THAT ARE

APPLICABLE TO YOUR EQUIPMENT.

1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions - All operating and use instructions should be followed.

5. Water and Moisture - The appliance should not be used near water-for example,

near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a

swimming pool and the like.

6. Carts and Stands - The appliance should be used only with a cart or stand that is

recommended by the manufacturer.

6A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

7. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the

manufacturer.

8. Ventilation - The appliance should be situated so that its location or position does not interfere with-its proper

ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may

block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may

impede the flow of air through the ventilation openings.

9. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or

other appliances (including amplifiers) that produce heat.

10.Power Sources - The appliance should be connected to a power supply only of the type described in the

operating instructions or as marked on the appliance.

11.Grounding or Polarization - Precautions should be taken so that the grounding or polarization means of an

appliance is not impeded.

12.Power - Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to cords at plugs, and the point

where they exit from the appliance.

13.Cleaning - The appliance should be cleaned only as recommended by the manufacturer.

14.This product is designed for use with the antenna attached and should not be connected to any other external

antennas.

15.Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for

a long period of time.

16.Object and Liquid Entry - Care should be taken so objects do not fall and liquids are not spilled into the

enclosure through openings

17.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:

A. The power-supply cord of the plug has been damaged; or

B. Objects have fallen, or liquid has been spilled into the appliance; or

C. The appliance has been exposed to rain; or

D. The appliance does not appear to operate normally or exhibits a marked change inperformance; or

E. The appliance has been dropped, or the enclosure damaged.

18.Servicing - The user should not attempt to service the appliance beyond that described in the operating

instructions. All other servicing should be referred to qualified service personnel.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE. DO NOT REMOVE COVER. PILOT LAMPS SOLDERED

IN PLACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

―Ventilation not being impeded.‖

―Do not exposed to dripping or splashing and that no objects filled with liquids,

such as vases, shall be placed on the apparatus.‖

Specification

FREQUENCY : FM 87.5 -108 MHz / AM 522 - 1620 KHz

POWER SOURCE : AC 230V~50HZ

ANTENNA : EXTERNAL 300 Ohm ANTENNA FOR FM

Built in ferrite bar for AM

POWER CONSUMPTION : 110W

SPEAKER :16.5cm Dynamic type x2

6.3cm Tweeter type x2

USB 2.0 PORT : Full Speed 512MB - 4GB(Support FAT16,FAT32)

*DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

The lighting flash with arrowhead

symbol, within an equilateral

triangle, is inten-ded to alert user

to the pre-sence of uninsulated

―dangerous voltage‖ within the

product’s enclosure that may be

of sufficient magnitude to

constitute risk of electric shock to

persons.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER -

SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The exclamation point within an

equilateral triangle is intended to

alert user to the presence of

important operating and

maintenance (servicing)

instruction in the literature

accompanying the appliance.

GETTING STARTED

1. Unwind the AC power cord at the back of the unit.

2. Connect the plug to the power wall outlet.

3. Press the MAIN POWER button on the back of the unit to switch the main power on.

4. Press the POWER button on the front of the unit to switch the unit to Standby mode.

5. Press the STAND BY button to begin the operation.

6 Press the LIGHT button to switch the LED lighting system on.

7. Connect the FM antenna to the ANTENNA JACK for better reception.

CD OPERATION

1. To switch to CD mode by pressing FUNCTION until CD appear on the LCD display.

2. Press OPEN/CLOSE to open the CD drawer.

3. Place a CD on the CD drawer .

5. The Total track no and Total play time of CD will show on the LCD display.

6. Press PLAY to start playing the CD

7. Press SKIP+ to go forward to the next track.

8. Press SKIP- to go backward to the previous track.

9. Press STOP to stop playing the CD.

10. Press PLAY/PAUSE when play a track to pause.

11. Press PLAY/PAUSE again to resume playing.

12. Press VOLUME UP to increase the sound volume (Maximum Value: 30)

13. Press VOLUME DOWN to decrease the sound volume (Minimum Value:0)

MP3 CD OPERATION

1. To Switch to CD mode by pressing FUNCTION until CD appear on the LCD display.

2. Press OPEN/CLOSE to open the CD drawer.

3. Place a MP3-CD on the CD drawer.

4. Press OPEN/CLOSE again to close the CD drawer. The total Album

number and total play time of MP3-CD will show on the LCD display.

( For e.g. 100 tracks file in 10 Albums evenly).

5. Press the PLAY/PAUSE button to play the MP3 tracks.

6. Press SKIP+ to go forward to the next track.

7. Press SKIP- to go backward to the previous track.

8. Press PRE-UP to go forward to the next Album.

9. Press PRE –DOWN to go backward to the previous Album.

10. Press STOP to stop playing the MP3-CD.

11. Press PLAY/PAUSE when play a track to pause.

12. Press PLAY/PAUSE again to resume playing.

13. Press VOLUME UP to increase the sound volume (Maximum Value: 30).

14. Press VOLUME DOWN to decrease the sound volume (Minimum Value: 0).

RADIO OPERATION

1. Press FUNCTION until TUNER appears on the LCD display.

2. Press BAND to select the desired waveband: FM or AM.

3. Press and hold SKIP+ or SKIP- until a radio station with sufficient signal.

strength is found. Repeat this procedure until the desired station is reached.

4. To tune into a weak station briefly press SKIP+ or SKIP- repeatedly until

the display shows the desired frequency or when the best reception has been obtained.

Note: 1. For FM Tuning, ((ST)) will show on the LCD display when stereo sound is obtained.

2. A maximum of 30 radio stations for FM and 10 for AM can be stored in the memory.

When a preset radio station is selected, the preset number appears on the display.

PROGRAMMING STATIONS

1. Press FUNCTION to TUNER mode.

2. Press AM/FM to select the desired wave band: FM or AM.

3. Press SKIP+ or SKIP- to tune to the desired frequency.

4. Press ―PROGRAM , the ―PROGRAM‖ and ―01‖ on LCD display will start flashing.

The current preset number will be displayed for selection.

5. If you wish to store the radio station to another preset number, press the PRE-UP or PRE-DOWN to

select the desired preset number.

6. Press PROGRAM on the unit again to store the radio station. Repeat steps 3 to 6 to store other preset

radio stations.

Note **During program, if no button is pressed within 5 seconds, the system will exit program mode

automatically.

SELECTING STATION

1. Press PRE-UP or PRE-DOWN to select the desired preset number. The preset number, radio frequency,

and PROGRAM will appear on the display.

2. Press MO./ST. on the Remote control to switch On or Off the stereo sound effect, stereo is On when

the ((ST))appears on the LCD display .

PROGRAMMING

Up to 64 tracks can be programmed for play in any desired sequence.

**The track must be programmed in Stop mode.

**The same track can be programmed more than once.

1. Press FUNCTION to switch to CD, or CARD-USB mode.

2. In stop mode, press the PROGRAM button. ―oo ― on top of LCD display starts flashing.

―Memory‖ and ―000 P - - 01‖ will show on the LCD display.

3. Press SKIP+ or SKIP- to select a desired Album.

4. Press the PROGRAM to store the selected album. ―oX‖ will be shown on the display and the ―000‖ will

start flashing. (where ―X‖ indicates the selected album)

5. Press SKIP+ or SKIP- again or using the numeric keys on the remote control select the desired track.

6. Press the PROGRAM to store the selected track. ―00‖, ―PROGRAM‖and ―000 P - - 02‖ will show on the

display.

7. Repeat steps 2 - 5 to select and store other desired tracks.

8. Press PLAY/PAUSE to start programmed playing from the PROGRAM 01 track.

9. To end the programmed play, press the STOP button.

RANDOM PLAYING

You can play all the tracks in random mode.

1. During playing, pause or stop mode, press RANDOM to enable random play mode.

―RANDOM‖ will appear on the display.

2. To exit RANDOM mode, press RANDOM again ―RANDOM‖ will disappear from the display.

REPEAT PLAYING

1. In stop or play mode, press the REPEAT once, ―REPEAT 1‖ will show on the LCD display. The selected

tracks will play repeatedly.

2. Press the REPEAT twice, ―REPEAT ALL‖ will show on the LCD display. All tracks will play repeatedly.

3. Press the REPEAT button for the third time, ―ALBUM REPEAT‖ will show on the LCD display,

the tracks in the selected Album will play repeatedly.

4. To exit the repeat mode, press the REPEAT button repeatedly until the ―REPEAT‖ icon disappears from

the LCD display.

Note: If "RANDOM" function has been selected, the repeat play mode will be disabled.

MUTE

Press the MUTE button to cut off the sound, the volume level bar on the right of the

LCD display will flash.

INTRO

Press the INTRO button, ―INTRO‖ will shown on the LCD display , the first 10 seconds of each track will play

automatically.

BBS

1. Press BBS once to switch ON the BBS sound effect.

2. Press BBS twice to switch OFF the BBS sound effect.

EQ

Press EQ repeatedly to choose the sound field as below sequence:

SEARCH PLAY (For MP3 CD only)

Search by Track name:

1. Press the FIND/ESP button once in Stop mode, on LCD display starts to flash.

2. Use SKIP+ or SKIP- to select the letter (A-Z) that match the first letter (A-Z) of the track's name.

3. Hold the SKIP+ or SKIP- for 1-2 seconds until the on LCD stops flashing.

4. Press SKIP+ or SKIP- to select the track starting with the selected letter (A- Z).

Search by Album name:

1. Press FIND/ESP twice in stop mode until ―ALBUM‖ and appears on the LCD display.

2. Press SKIP+ or SKIP- repeatedly to select an Album.

3. Hold the SKIP+ or SKIP- for 1-2 seconds to enter the selected Album,―ALBUM‖ will disappear on the LCD

display.

4. Press SKIP+ or SKIP- to select the track in the selected Album.

5. Press PLAY/PAUSE to play the selected track.

**If there are files in the root directory, the display will show ―Root‖. Hold SKIP+ or SKIP- for 1-2 seconds

until ―ALBUM‖ disappears from the LCD display. Then search the files in the root directory by pressing SKIP+

or SKIP- .

MP3 INFORMATION

1. If the MP3 file has track information stored on it, such as Artist and Title, the LCD will display that

information during MP3 CD playback.

2. Press and hold the FIND/ESP button over 1 second - MP3 information will show on the LCD.

NOTE: If the MP3 was recorded without any track information, ―UNKNOWN‖ or ―NONE‖ will be displayed

when the Find button is pressed.

ESP MODE

Shockproof function "ESP" can be set in CD mode only. Press the FIND/ESP button to switch the ESP function

on in CD mode and ―ESP‖ will appear on the LCD display. Press FIND/ESP again. "ESP" will disappear on the

LCD display.

USB OPERATION

1. Press the FUNCTION button until "USB" appears on the LCD display.

2. Connect the USB device (MP3 Player or USB Flash Memory Drive with stored music files) to the USB PORT.

Note: The unit can only play MP3 files up to 4GB max. and does not play WMA files.

3. Repeat Steps 5 to14 of MP3 CD OPERATION.

SD CARD OPERATION

1. Press the FUNCTION button until "CARD" appears on the LCD display.

2. Inster an SD Card with pre-recorded MP3 music (not supplied) into the card slot.

Note:The unit can only play MP3 files up to 4GB max. and does not play WMA files.

3. Repeat Steps 5 to14 of MP3 CD OPERATION.

USB SPECIFICATION

Interface

* USB2.0 Full speed, HOST (USB HUB is not supported)

Corresponding Flash Memory

* USB1.1 Flash memory

* USB2.0 High speed Flash memory

* Minimum memory size: 512MByte

* Maximum memory size: 4GByte

MP3 Decoder

* Compatible with MPEG Audio 1, 2, 2.5

* Compatible with Layer 1, 2, 3

* Compatible with Sampling rate: 8k, 16k, 32k, 11.025k, 22.05k, 44.1k, 12k, 24k,48kHz

* Compatible with Bit rate: 128k ~ 320kbps

* Subfolder nest: 8

* Number of track/titles Max 999

* Support ID3 tag V2.0

IMPORTANT NOTES

The USB connector does not support connection with a USB extension cable and is not designed for direct

communication with a Computer. It is not guaranteed that all USB memory devices & SD Card will work on this

audio system. Do not disconnect the USB device/SD Card during USB/CARD mode, as this may damage the

external device or its files. Please first switch to another Mode or power off before safely disconnecting the USB

device/SD Card.

Location of parts

USB jack

SD card slot

Speakers

Mute button

LCD Display

Sensor

Standby button

EQ button

Power button

Find/ESP button

Function button

Play / pause button

Stop button

Open/Close button

CD/Tuner skip + button

CD/Tuner skip - button

Volume down button

Intro button

Light button

BBS button

Band button

Repeat button

Random button

Program button

Album pre-up button

Album pre-down button

Volume up button

CD drawer

Remote location

Red

Black

Red

Black

Metal

conductor

FM Antenna : 300 Ohm Jack

Main power button

AUX.in Jack

Lighting switch

(Release/hold)

Earphone

Internal / External speaker switch (int./Ext.)

Ext. Speaker jack

Power / Standby button

Function button

Mute button

Volume up button

EQ button

BBS button

Volume down button

Repeat button

Random button

0-9 button

AM / FM button

AUX button

Find / ESP. Mono / Stereo button

Preset + button

Scan / Skip + button

Scan / Skip - button

Preset - button

Program button

Intro button

Stop button

Play / Pause button

CUSTOMER SUPPORT

You can contact the Ricatech customer service when you have a question or a problem with your

Ricatech product. You can contact us by telephone and email.

Email

For customer support by email, please sent a email to

[email protected]

Please make sure that

you mention the model number and serial number of the product, mention your name & address and

describe your question or problem clearly.

Telephone

For customer support by telephone, please dial +32 3 3265694. One of our service staff will be ready

to serve you.

For full procedure please visit the website of Ricatech at: www.ricatech.com

Page is loading ...

Plaats van onderdelen

usb-

aansluiting

SD-kaartsleuf

Luidsprekers

Mute-knop

LCD Display

(lcd-scherm)

Sensor

Stand-byknop

EQ-knop

Stroomtoevoerknop

Find/ESP-knop

Function-knop

Play/Pause-knop (Afspelen/Pauze-knop)

Stop-knop

Open/closeknop

cd/Tuner skip + knop

CD/Tuner skip - knop

Volume down-knop

Introknop

Lichtknop

BBS-knop

Bandknop

Repeat-knop

Random-knop

Program-knop

Album pre-up-knop

Album pre-down-knop

Volume up-knop

cd-lade

Afstandsbedieningslocatie

Rood

Zwart

Rood

Zwart

Metalen

geleider

FM-antenne : 300 Ohm Aansluiting

Hoofdstroomtoevoerknop

AUX.in-Aansluiting

Lichtschakelaar

(Loslaten/vasthouden)

Koptelefoo

n

Interne / Externe luidsprekerschakelaar

(int./Ext.)

Ext. Luidsprekeraansluiting

Stroom / Stand-byknop

Function-knop

Mute-knop

Volume up-knop

EQ-knop

BBS-knop

Volume down-knop

Repeat-knop

Random-knop

0-9-knop

AM / FM-knop

AUX-knop

Find / ESP. Mono / Stereo-knop

Preset + knop

Scan / Skip + knop

Scan / Skip - knop

Preset - knop

Program-knop

Introknop

Stop-knop

Play / Pause-knop

Page is loading ...

Ricatech RR1600 User manual

Ricatech RR1600 User manual

in other languages

Related papers

Other documents