NOTICE:
Read and follow the instructions in this manual to ensure correct assembly of this product.
Keep children and pets away from assembly area unless they are supervised.
Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house,
overhanging branches, laundry line, or electrical wires.
Some parts may have sharp edges. When assembling and using this product, basic safety
precautions should always be followed to reduce the risk of personal injury and damage to the
product.
Assemble on level ground.
Check all bolts for tightness before use, and periodically check and tighten bolts as necessary.
This unit is heavy. Do not assemble this item alone.
OWNER'S MANUAL
HARDTOP GRILL GAZEBO
ITEM: L-GG029PST
Roof Vent A 2
Base B 4
Base Cover C 4
Truss Beam (1) D1 2
Truss Beam (2) D2 2
Top Connecting Pole E 1
Connecting Board 1 F1 2
Connecting Board 2 F2 2
Connecting Board 3 F3 4
Top Hook G 1
Roof Cladding – long
panel (1) H1 2
Roof cladding – long
panel（2） H2 2
Roof Cladding – long
panel（3） H3 2
Roof Cladding – short
panel（1） I1 2
Roof Cladding – short
panel（2） I2 2
Roof Cladding – short
panel（3） I3 2
Trim Cap J 1
Pole （1） K1 2
Pole （2） K2 2
Skew Support Piece L 4
Countertop M 2
Screen N 2
Cover Supporting
Board O 6
Parts List
AA M6X20 Screw 40PCS
BB M6 Washer 40PCS
Z M6 Wrench 2 PCS
Hardware Pack Used in Step 1
Fig.1: Attach truss beam D1 (D2) to top roof vent (A), assemble them with baffle (F2) by using screw (AA) and
washer (BB).
Fig.2: Attach top hook (G) to Top Connecting Pole (E).
Fig.3: Attach Top Connecting Pole (E) to top roof vent (A) by using screw (AA) and washer (BB)
Fig.4: Attach Connecting Board (F3) to top roof vent (A) by using screw (AA) and washer (BB)
Fig.5: Attach Truss Beam D1 (D2) to Connecting Board (F3) by using screw (AA) and washer (BB)
Fig.6: Attach Connecting Board F1 to Truss Beam D1 (D2) by using screw (AA) and washer (BB)
BB M6 Washer 42PCS
CC M6X15 Screw 40PCS
DD M6X35 Screw 2 PCS
Hardware Pack Used in Ste
p
2
Fig.7: Attach the Roof cladding – short panel (I1 I2 I3) to Cover Supporting Board (O) by using screw (CC) and
washer
(
BB
)
Fig.9: Attach trim cap (J) to Top Connecting Pole by using screw (DD) and washer (BB).
Fig.8: Attach Roof cladding – long panel (H1 H2 H3) to Cover Supporting Board (O) by using screw (CC) and
washer (BB)
AA M6X20 Screw 40PCS
BB M6 Washer 48PCS
CC M6X15 Screw 8PCS
II Φ8X180 Stake 8 PCS
Hardware Pack Used in Step 3
Fig.10: Insert Base cover (C) into Pole (K1&K2), attach Base (B) and Pole K1&K2 by using screw (CC), washer
(BB).
Fig.11: Lift the assembled top frame, insert into Pole K1&K2, locked them by using screw (AA), washer (BB).
Fi
g
.12:
A
ttach Screen
(
N
)
to Pole
(
K1&K2
)
b
y
usin
g
screw
(
AA
)
, washer
(
BB
)
.
Fig.13: Attach Skew support piece (L) onto Pole K1 (K2) and Truss Beam D1 (D2) by using screw
(AA), washer (BB).
Fig.14: Attach Countertop M onto Pole K1 (K2) by using screw (AA), washer (BB).
Fig.15: Lift up Base cover (C), use (II) to fasten the gazebo on the ground. Put down Base cover
(C) and now your gazebo is ready for use.
Care & Maintenance
Steel components of garden accessories and furniture are treated with rust inhibiting paint that
protects them from rust. However, due to the nature of steel, surface oxidation (rusting) will occur if
this protective coating is scratched. This is a natural process. To minimize this condition, it is
recommended that care be taken when assembling and handling the product, in order to prevent
the paint from being scratched. If scratching or damage occurs, it is recommended that the area be
touched up immediately with rust inhibiting paint, which is included in the package. Surface rust can
be removed easily using a very light application of common cooking oil. If surface oxidation
(rusting) occurs and no measures are taken to correct it, the oxidation may start dripping onto the
deck or patio, which may cause damaging stains that may be difficult to remove.
Please do not return this product to the store. For technical assistance on assembly or
replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am EST to
8:00 pm PST or fax the replacement part form which is in the box to 1-740-283-3549 or
Email [email protected] for assistance.
Made in China
2016-4
/
