Sunjoy D-GZ841PST-C User manual

Assembly Instructions

Item# D-GZ841PST-C (PC Top)

Congratulations on your purchase of our SUNJOY 12’x10’ Hardtop Gazebo. Our clear, easy to

follow, step-by-step instructions will guide you through the assembly process from start to

finish.

● This unit is heavy. Do not assemble this item alone. 6-8 people are recommended for safe

assembly.

WARNING:

● Keep all children and pets away from assembly area. Children and pets should be supervised

when they are in the area of the Gazebo construction.

● Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house,

overhanging branches, laundry line or electrical wires.

● Some parts may contain sharp edges. When assembling and using this product, basic safety

precautions should always be followed to reduce the risk of personal injury and damage to the

product. Please read all instructions before assembly and use.

● Check all bolts for tightness before use, and periodically check and tighten bolts as necessary.

● Assemble on level ground

.

IMPORTANT

Please do not return this product to the store. For technical assistance on assembly or replacement

parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am EST to 8:00 pm PST or fax the

replacement part form which is in the box to 1-740-283-3549 or Email customer.care@sunjoygroup.com

for assistance.

Big panel 1 A1 2

Big panel 2 A2 2

Small panel 1 B1 2

Small panel 2 B2 2

Fence C 8

Connector D 4

Top connector E 4

Lower connector F 4

Short beam1 G1 2

Short beam2 G2 2

Long beam1 G3 2

Long beam2 G4 2

Long top bar I1 2

Corner frame I2 2

Oblique beam J 4

Middle beam 1 K1 2

Middle beam 2 K2 2

PC piece 1 M1 4

PC piece 2 M2 4

PC piece 3 M3 4

PC piece 4 M4 4

PC piece 5 M5 4

PC piece 6 M6 2

PC piece 7 M7 2

Parts List

Big left cover N1 4

Big right cover N2 4

Middle cover N3 2

Small cover 1

O1

2

Small cover 2

O2

2

Left rail P1 4

Right rail P2 4

Middle rail P3 2

Center plate Q1 6

Corner plate Q2 8

Hook R 1

Small top connector S 1

Cover T 1

Small slanted beam U 4

Panel wall W 8

Long netting bar 1 W1 2

Long netting bar 2 W2 2

Short netting bar 1 W3 2

Short netting bar 2 W4 2

Cover flap 1 X1 2

Cover flap 2 X2 4

Cover flap 3 X3 4

BB M6 Flat washer 124 PCS

DD Nut 16PCS

FF M6X15 Bolt 64 PCS

GG M6X70 Bolt 16 PCS

LL M6X35 Bolt 16 PCS

HH M6X25 Bolt 12 PCS

Z M6 Wrench 2 PCS

Hardware Pack 1

Fig.1: Secure the fence (C) to the

panels (A1/A2/B1/B2) by using bolts

(FF) and flat washers (BB).

Fig.2: Connect big panel 1 (A1) and small panel 1 (B1) by using

bolts (JJ), flat washers (BB), repeat this for big panel 2 (A2) and

small panel 2 (B2).

Hardware Pack 2

Fig.3: Fix top connector (E) and

lower connector (F) onto short

beam / long beam (G1/G3) by

using bolts (GG), flat washers

Fig.4: Attach assembly beams

(G1/G2) to big panel 1 / big panel 2 /

small panel 1 / small panel 2 (A1/A2

/B1/B2) by using flat washers (BB),

bolts (FF) and bolt (LL) separately.

Fig.5: Secure the connector (D) to

the beams by using bolts (FF) and

flat washers (BB).

AA M6X15 Screw 24 PCS

BB M6 Flat washer 80 PCS

FF M6X15 Bolt 4 PCS

DD Nut 16 PCS

EE M6X20 Bolt 20 PCS

JJ M6X60 Screw 16 PCS

Fig.7: Fix oblique beam (J)

to corner frame (I2) by

using bolts (EE) and flat

washers (BB)

Fig.9: Attach middle beam 1

(K1) to (I2) by using by

using bolts (EE) and flat

washers (BB)

Fig.11: Attach the upper side of middle beam 2

(K2) to long top bar (I1) by using bolts (EE), flat

washers (BB)

Fig.13: Connect cover flap

(X2) to small slanted beam

(U) and fix small slanted

beam (U), cover flap 2

(X2), small top connector

(S) by using bolts (JJ), nuts

(DD), flat washers (BB)

Fig.15: Insert and screw

the hook (R) tightly into the

corresponding hole on the

small top connector (S).

Fig.6: Insert long top bar (I1) into corner frame (I2) and fix them by using bolts (AA) and flat washers (BB).

Fig.11-1: Attach the lower side

of middle beam 2 (K2) to lower

connector (F) by using bolts

(JJ), flat washers (BB), nuts

(DD).

Fig.12-1: Attach netting

bar1/2/3/4(W1/W2/W3/W4)

to middle beam 1/2 (K1/K2)

by using bolts (AA), flat

washers (BB).

Fig.12-2: Fix the other side

of netting bar 1/2/3/4

(W1/W2/W3/W4) to oblique

beam (J) by using bolts

(AA), flat washers (BB).

Fig.8:Connect cover flap 3 (X3)

to the lower end of oblique beam

(J) and fix oblique beam (J),

cover flap 3 (X3), top connector

(E) by using bolts (JJ), nuts (DD),

flat washers (BB)

Fig.10: Connect cover flap 1

(X1) to middle beam 1 (K1), and

fix cover flap 1 (X1) to middle

beam 1 (K1), lower connector

(F) by using bolts (JJ), nuts

(DD), flat washers (BB).

Fig.14: Fix small slanted

beam (U) and corner frame

(I2) by using bolts (FF), flat

washers (BB).

K2

Hardware Pack 3

AA M6X15 Screw 14 PCS

BB M6 Flat washer 16 PCS

HH

M6X60 Bolt 2 PCS

Fig.16: Insert the PC piece

(M6/M7) into the rail on the small

slanted beam (U).

Fig.17: Insert the Small cover (O1 and O2)

into the lower of the PC piece 6/7 (M6 and

M7), then secure the corner plate (Q2) to

the small slanted beam (U) through three

holes with screws (AA) and flat washers

(BB).

Fig.18: Secure the cover (T) to the

small top connector (S) with bolts

(HH) and flat washers (BB)

Fig.19: Insert the PC piece 3/4

(M3/M4) into the middle beam

(K1/K2) and Oblique beam (J),

then insert the rails (P1/P2) into

it. Insert the PC piece 1/2

(M1/M2) into the middle beam

(K1/K2) and Oblique beam (J).

Repeat this step to install the

right roof pieces.

Fig.20: Insert the PC piece

5 (M5) into the middle

beam 2 (K2); then insert

the middle rail (P3) into it.

Insert the PC piece (M5)

into the middle beam 2

(K2).

Fig.21: Insert the cover (N1,

N2 and N3) into the lower of

PC pieces; then secure the

center plate (Q

1) to the

middle beam 2 (K2) through

three holes with screws

(AA) and flat washers (BB).

Fig.22: Secure the corner

plate (Q2) to the Oblique

beam (J) through three

holes with screws (AA) and

flat washers (BB).

IMPORTANT:

Hardware Pack 4

KK

Φ6X260 Stake

16 PCS

Fig.24: Secure the whole gazebo

to the ground with stakes (KK).

Fig.23: Assemble the panel Wall

(W) by using velcro straps.

1. Keep all children and pets away from assembly area. Children and pets should be

supervised while gazebo is being assembled.

2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction such as

a fence, garage, and house, overhanging branches, laundry lines or electrical wires.

3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe

assembly.

4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.

5. When assembling and using this product, basic safety precautions should always be

followed to reduce the risk of personal injury and damage to equipment. Please read all

instructions before assembly and use.

6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the gazebo in

the ground. If you wish to secure the pavilion to a wood deck or concrete surface, use 16

anchors suited for these surfaces (anchors not included).

7. Check all bolts for tightness before and during usage.

8. Please check your state and local regulations prior to purchasing. Some jurisdictions may

require permits for installation and use. Some special procedures may be valid in your area.

9. While this gazebo is manufactured to withstand strong force winds through only the supplied

ground stakes, securing the gazebo to a deck, concrete patio or a stronger base, in areas

subject to frequent severe weather should be considered.

NOTE: The gazebo’s roof and structure are not guaranteed against extreme weather

conditions (storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow must

be cleaned off regularly. Any damage caused by snow accumulation is not covered by the

warranty.

Limited Warranty:

This limited warranty is extended to the original purchaser and applies to defects in materials

and workmanship of your item provided the item is maintained with care and used only for

personal, residential purposes.

The item is warranted to be free from defects in material or workmanship for a period of one (1)

year. We don't reimburse for transportation or delivery costs, or compensate the individual or

any outside party for assembling or disassembling the product.

Items used for commercial, contract, or other non-residential purposes, or items damaged due

to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or

rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for

warranty claims. Warranty is to the original purchaser and is non-transferable. Any

replacement of warranted items will be in the original style and color, or a similar style and

color if the original is unavailable or has been discontinued. As some states do not allow

exclusions or limitations on an implied warranty, the above exclusions and limitations may not

apply. This warranty gives you specific rights, and you may also have other rights, which vary

from state to state.

Exclusions:

Maintenance:

Our iron/steel components for garden accessories and patio items are coated with rust

inhibiting paint that protects it from rusting.

However, due to the nature of iron, surface

oxidation (rusting) will occur once these protective coatings are scratched.

This is a natural

process and is not a defect! To minimize this condition, we recommend care when assembling

& handling the product to prevent scratching the paint. Should any scratching or damage occur,

we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily

removed with a very light application of common cooking oil. If surface oxidation (rusting)

occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck or

patio and cause damaging stains, which may be difficult to remove. This can be prevented if

measure is taken to keep the product from oxidizing.

mportant: Please do not return this product to the store. For technical assistance on

assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am

EST to 8:00 pm PST or fax the replacement part form which is in the box to 1-740-283-3549 or

Email customer.care@sunjoygroup.com for assistance.

Made in China

GAZEBO NETTING AND CURTAIN ASSEMBLY INSTRUCTIONS

Netting or Curatin is available separatley

Ring 104PCS

Fig.1: Hang the mosquito net and curtain onto the netting tubes (W1, W2, W3 and W4) by using rings, please

put the mosquito net inside.

Sunjoy D-GZ841PST-C User manual

This manual is also suitable for

Sunjoy D-GZ841PST-C User manual

Related papers

Other documents