Pitney Bowes SendPro P-Series |Connect ® Series Owner's manual

Brand: Pitney Bowes

Model: SendPro P-Series |Connect ® Series

Type: Owner's manual

This manual is also suitable for

SendPro P-Series |Connect+® Series

Pitney Bowes SendPro P-Series |Connect ® Series

This device is a multi-branch AC line cord kit for use with SendPro™ P Series components. The following are the only devices allowed to be connected to the multi-branch AC line cord kit:

• SendPro™ P Series • Display AC adapter (for 15” display only) • Power Stacker AC adapter

Use only supplied Connect+™ | SendPro™ P Series system power cord. Do not connect to other devices.

For use only with Connect+™ Series components

Capabilities:

• The Pitney Bowes SendPro P-Series |Connect ® Series can be used to connect multiple SendPro™ P Series components to a single power source.

Pitney Bowes SendPro P-Series |Connect ® Series

This device is a multi-branch AC line cord kit for use with SendPro™ P Series components. The following are the only devices allowed to be connected to the multi-branch AC line cord kit:

• SendPro™ P Series • Display AC adapter (for 15” display only) • Power Stacker AC adapter

Use only supplied Connect+™ | SendPro™ P Series system power cord. Do not connect to other devices.

For use only with Connect+™ Series components

Capabilities:

• The Pitney Bowes SendPro P-Series |Connect ® Series can be used to connect multiple SendPro™ P Series components to a single power source.

The multi-branch AC line cord kit is for use with SendPro™ P Series components.

The following are the only devices allowed to be connected to the multi-branch AC line cord kit:

• SendPro™ P Series

• Display AC adapter (for 15” display only)

• Power Stacker AC adapter

Important Safety and Compliance Information for Your Mailing System

Follow the normal safety precautions for all office equipment.

• Use the power cord supplied with the system and plug it into a properly grounded wall outlet located near the

system and easily accessible. Failure to properly ground the system can result in severe personal injury and/or

fire.

• The power cord wall plug is the primary means of disconnecting the system from the AC supply.

• Do not use an adapter plug on the line cord or wall outlet.

• Do not remove the ground pin from the line cord.

• Avoid using wall outlets that are controlled by a wall switch, or shared with other equipment.

• Do not route the power cord over sharp edges or trap between furniture.

• Ensure there is no strain on the power cord where it becomes jammed between the equipment, walls or

furniture.

• Be certain the area in front of the wall receptacle into which the system is plugged is free of obstruction.

• Your MSD2 15” monitor and MSPS stacker have specific AC adapters to power them.

Do not use third-party AC adapters which may damage the monitor and the stacker.

NOTE: Always follow the specific occupational safety and health standards for your workplace.

Do not connect to other devices

For use only with

Connect+™ Series components

system

display

stacker

Use only supplied Connect+™ | SendPro™ P Series system power cord

Connect+

™

| SendPro

™

P Series Power Distribution Kit

AW22653 Rev D 02/2016

Do not connect to other devices such as laser printers.

No conectar a otros dispositivos tales como impresoras láser.

Para utilizar sólo con componentes de la serie Connect+

™

| SendPro

™

sistema

systeem

system

systeem

système

apilador

raccoglitore

mottager

opvang

ablage

avläggare

stacker

réception

visor

display

beeldscherm

afficheur

Connect+

™

| SendPro

™

P Series Power Distribution Kit

Non collegare altri dispositivi come stampanti laser ecc.

Da utilizzarsi solo con componenti della Serie Connect+

™

| SendPro

™

Må ikke koples sammen med annet utstyr som f.eks. laser printere.

Kun for bruk sammen med Connect+

™

| SendPro

™

P Serie komponenter.

Niet aansluiten op andere apparaten zoals laser printers.

Alleen voor gebruik met Connect+

™

| SendPro

™

P Serie componenten.

Keine anderen Geräte, wie z.B. Laserdrucker anschliessen.

Nur mit Komponenten der Connect+

™

| SendPro

™

P Serie verwenden.

Anslut inte till andra enheter som t.ex. laserskrivare.

Används enbart ihop med delar till Connect+

™

| SendPro

™

Opret ikke forbindelse til andre enheder såsom laserprintere.

Må kun anvendes med Connect+

™

| SendPro

™

P seriens komponenter.

Ne pas connecter avec d’autres produits tels que des imprimantes laser.

Pour utilisation uniquement avec des éléments Connect+

™

| SendPro

™

P Series.

Pitney Bowes SendPro P-Series |Connect ® Series Owner's manual

Brand: Pitney Bowes

Model: SendPro P-Series |Connect ® Series

Type: Owner's manual

This manual is also suitable for

SendPro P-Series |Connect+® Series

Pitney Bowes SendPro P-Series |Connect ® Series

This device is a multi-branch AC line cord kit for use with SendPro™ P Series components. The following are the only devices allowed to be connected to the multi-branch AC line cord kit:

• SendPro™ P Series • Display AC adapter (for 15” display only) • Power Stacker AC adapter

Use only supplied Connect+™ | SendPro™ P Series system power cord. Do not connect to other devices.

For use only with Connect+™ Series components

Capabilities:

• The Pitney Bowes SendPro P-Series |Connect ® Series can be used to connect multiple SendPro™ P Series components to a single power source.

Download PDF

report