Bauknecht DKE 1360 IN Program Chart

Category
Cooker hoods
Type
Program Chart

This manual is also suitable for

5019 418 33045
DKE 1390 - DKE 1360 - DKEL 1760
INSTALLATIONSBLAD
Minsta tillåtna avstånd från olika typer av spisar: 60 cm (elektrisk spis), 75
cm (gasspis, gasolspis och koleldad spis). Följ numreringen nedan för
monteringen: (1
Ö
2
Ö
3
Ö
.....). Slå inte på strömmen till fläktkåpan förrän
installationen är helt avslutad.
INSTALLASJONSVEILEDNING
Minimumsavstand til komfyrtopp: 60 cm (elektriske kokeplater), 75 cm
(gass-, parafin- eller kullkomfyr). Følg nummereringen ved montering
(1
Ö
2
Ö
3
Ö
.....). Apparatet må ikke tilkobles strømnettet før installasjonen
er helt avsluttet.
INSTALLATIONSVEJLEDNING
Minimumafstand fra kogezoner: 60 cm (elkogezoner), 75 cm (gas-, olie-
eller kulfyrede kogezoner). Ved montering skal man følge vejledningens
nummerrækkefølge (1
Ö
2
Ö
3
Ö
.....). Apparatet må ikke tilsluttes
elforsyningen, før installationen er fuldført.
ASENNUSOHJEET
Vähimmäisetäisyys liedestä: 60 cm (sähkölevyt), 75 cm (kaasu-, öljy- tai
hiililiedet). Suorita kokoonpano numerojärjestyksessä (1
Ö
2
Ö
3
Ö
.....). Älä
kytke laitetta sähköverkkoon ennen kuin kokoonpano on kokonaan
suoritettu.
INSTALLATION SHEET
Minimum height above cooker: 60 cm (electric cookers), 75 cm (gas, gas oil
or coal cookers). To install follow points (1
Ö
2
Ö
3
Ö
.....). Do not connect the
appliance to the electrical power supply until installation is completed.
S
N
DK
FIN
GB
41833045.fm Page 1 Thursday, December 11, 2003 10:37 AM
5019 418 33045
DKE 1390 - DKE 1360 - DKEL 1760
R
T
Y
Y
Y
Y
R
T
!
S
U
1
2
V
Z
W
41833045.fm Page 2 Thursday, December 11, 2003 10:37 AM
5019 418 33045
DKE 1390 - DKE 1360 - DKEL 1760
V
X
Z
F
J
D
G
P
M
L
3
4
41833045.fm Page 3 Thursday, December 11, 2003 10:37 AM
5019 418 33045
DKE 1390 - DKE 1360 - DKEL 1760
FIN
S N DK GB
Assembly - fig. 1-2-3-4
In order to facilitate installation of the hood and flue support, trace a centre line on the wall
between the hob and ceiling (
Z
).
Position the template against the wall, then mark and drill the holes where indicated (
Y
).
Insert two wall plugs with hooks (
V
).
Hang the hood and adjust the position by turning the adjustment screws (
S
).
Remove the grease filters and mark the holes for secure fixing (
T-R
).
Remove the hood and drill the holes (4 x Ø 8 mm).
Insert 4 wall plugs and two screws in the top holes: they will ensure secure fixing (
X
).
Fix the flue support (
Z
) as close as possible to the ceiling with two screws and wall plugs.
Important! Check that the support is perfectly aligned with the hood.
Rehang the hood on the wall.
Fix the hood with two screws at the bottom (
D
).
Installing the exhaust pipe (Extractor version)
Warning! The exhaust pipe and clamps are not supplied and must be bought separately.
Connect one end of the exhaust pipe (
J
) to the hood (
G
) with the other end directed to the
outside.
Installing the deflector (Filter version)
Fix the deflector (
F
) to the flue support with 4 screws.
Connect the deflector to the hood with an exhaust pipe.
Warning! The exhaust pipe and clamps are not supplied and must be bought separately.
Installing the telescopic flue
Connect the hood to the power supply.
Fix the telescopic flue (
M
) to the support (
Z
) with two screws and let it slide down to its
specific seat on the top of the hood.
41833045.fm Page 13 Thursday, December 11, 2003 10:37 AM
5019 418 33045
DKE 1390 - DKE 1360 - DKEL 1760
FIN
S N DK GB
1.
Control panel
2.
Grease filters
3.
Lighting unit
4.
Telescopic flue
5.
Grease filter release-replace handle
Removing and renewing or
washing the grease filter
1.
Disconnect the electrical power supply.
2.
Remove the grease filters (
Fig. 5
):
a
- push the handles backwards
b
- then downwards.
3.
After the grease filter has been replaced or
cleaned (depending on model), refit the parts in
reverse order, making sure the entire extraction
surface is covered.
Replacing bulbs
1.
Disconnect the electrical power supply.
2.
Remove the grease filters.
3.
Remove the burnt-out bulb.
Replace using 40W max (E14) bulbs only.
4.
Refit the lighting unit.
Fitting or renewing the carbon
filter - Fig. 6:
1.
Disconnect the electrical power supply.
2.
Remove the grease filters.
3.
If the filters are not already fitted, locate one on
each side to cover both motor protection grilles,
check that pins
R
on the duct align with slots
S
,
then turn it clockwise until it locks.
4.
To remove the carbon filter, proceed in reverse
order.
5.
Replace the grease filters.
CONTROL PANEL
A.
Light switch.
B.
Speed selector switch.
Fig. 5
4
2
3
3
1
OI O123i
A
B
Fig. 8
Very large amount of
steam and fumes (only
model DKEL 1760)
R
R
S
S
Fig. 7
Small amount of
steam and fumes
Medium amount of
steam and fumes
Large amount of steam
and fumes
Fig. 6
PRODUCT DESCRIPTION SHEET
41833045.fm Page 14 Thursday, December 11, 2003 10:37 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Bauknecht DKE 1360 IN Program Chart

Category
Cooker hoods
Type
Program Chart
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages