Astria Fireplaces Rhapsody Instruction Sheet

Brand: Astria Fireplaces

Model: Rhapsody

Category: Fireplaces

Type: Instruction Sheet

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

HEARTH PRODUCTS

KITS AND ACCESSORIES

P/N 900077-05

Rev. A 09/2016

LINEAR DIRECT-VENT FIREPLACES

ACCESSORY KITS

INSTALLATION INSTRUCTIONS FOR REQUIRED AND OPTIONAL ACCESSORIES

FOR USE ON 42- AND 54-INCH LINEAR DIRECT-VENT GAS FIREPLACES

[FIREPLACE MODELS: Rhapsody42 and Rhapsody54 Series]

DANGER

HOT GLASS WILL CAUSE BURNS. DO NOT

TOUCH GLASS UNTIL COOLED.

NEVER

ALLOW CHILDREN TO TOUCH GLASS.

• Fireplaces surfaces get EXTREMELY HOT!

• Install only when ﬁ replace is OFF and COLD.

• The glass on the front of the ﬁ replace reaches

EXTREMELY HIGH temperatures and can cause severe

burns if touched. Even after the gas is turned off,

ﬁ replace surfaces remain extremely hot.

• Keep children away from an operating ﬁ replace. Closely

supervise children in any room where a ﬁ replace is

operating to prevent contact with glass.

CAUTION

RISK OF PERSONAL INJURY OR PROPERTY DAMAGE.

• Never operate fireplace without liner panels installed. These

appliances are NOT approved for operation without liner panels.

• Do NOT abuse glass doors by striking or slamming shut

• Never operate ﬁ replace with glass door assembly removed.

• Handle glass door assembly with extreme care.

Replace damaged glass door assembly with approved

replacement assembly only.

• Use only media approved for use with these ﬁ replaces

(as applicable). Failure to use approved media may result

in sooting, delayed ignition, or other improper ﬁ replace

operation, and may void the warranty.

NOTICE

• Read all steps before starting installation.

• LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE.

• All warnings, precautions, and instructions in the Installation

and Operation Instructions provided with the appliance also

apply to these instructions.

• If you encounter any problems, need clariﬁ cation of these

instructions, or are not qualiﬁ ed to properly install this

kit, contact your local distributor or dealer.

Figure 1 - 54 in. Rhapsody linear gas ﬁ replaces with

designer ﬂ oor kit and Illusion Cityscape ﬁ rebox

panel kit (both in black porcelain).

GENERAL INFORMATION

This document contains installation instructions for the following

required and optional accessories for Rhapsody® linear direct-

vent gas ﬁ replaces manufactured by INNOVATIVE HEARTH

PRODUCTS (IHP).

Kit descriptions, catalog/model numbers, and contents are listed

on the next page.

Required Accessory Kits

The following accessory kits are REQUIRED for complete ﬁ re-

place installation.

NOTE: Ensure these kits are available before installing the ﬁ re-

place.

• Firebox Panel Kit (Rhapsody models only)

• Floor Kit (Rhapsody models only)

• Media Kit *

* Media kit required with “Designer" style ﬂ oor kits only (Rhapsody models only)

Media must not be used with Refection ﬂ oor.

Optional Accessory Kits

The following accessories are OPTIONAL. However, to minimize

required labor, all options should be installed at time of ﬁ replace

installation, if possible.

• Surround Kit

• Bezel Kit

• Firebox Backlight Kit ** (Rhapsody models only)

• Power Vent Kit

(see manual 506022-01 for installation instructions)

** Firebox backlight kit for use with "Cityscape" and "Illusion" style ﬁ rebox

panel kits (Rhapsody models only)

REQUIRED TOOLS

NOTE: Power tools are NOT recommended when installing ﬁ re-

place accessories, especially porcelain ﬁ rebox panels.

• 5/16" Hex-head Nut Driver

• #3 Phillips Head Screwdriver

(for ﬁ replace door removal/installation)

• Glass Cleaner (non-ammoniated)

• Non-abrasive rag

• High-temperature sealant

(e.g., Mill-Pac®; if installing ﬁ rebox backlight kit)

• Safety Glasses

• Protective Work Gloves

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

REQUIRED ACCESSORIES

Firebox Panel Kits

• (13) #10-16 x 3/8 Hex-head Sheet Metal Screws

• (2) Side Panels

• (1) Back Panel

Illusion Cityscape Back Panel Illusion Metroscape Back Panel

42 in.

Illusion Cityscape—Black Porcelain * H8832 IPK-CBLKP-RAP42

Illusion Metroscape—Black Porcelain * H8833 IPK-MBLKP-RAP42

Nake—Black Porcelain H8834 NPK-BLP-RAP42

Nake—Black Satin Paint H8835 NPK-BLS-RAP42

54 in.

Illusion Cityscape—Black Porcelain * H8420 IPK-CBLKP-RAP54

Illusion Metroscape—Black Porcelain * H8421 IPK-MBLKP-RAP54

Nake—Black Porcelain H8422 NPK-BLP-RAP54

Nake—Black Satin Paint H8423 NPK-BLS-RAP54

Table 1 - Required Firebox Panel Kits

* “Illusion” and "Cityscape" style Firebox Panel Kits are designed for use with

the Illusion and Cityscape Firebox Panel Backlight Kits.

Floor Kits

• (4) #10-16 x 3/8 Hex-head Sheet Metal Screws

• (1) Rear Floor Section

• (1) Front Floor Section

Designer Floor Kit

Description Cat. No. Model No.

42 in.

Reﬂ ection—Black Porcelain H8838 RFK-BLP-RAP42

Designer—Black Porcelain ** H8836 DFK-BLP-RAP42

Designer—Black Satin ** H8837 DFK-BLS-RAP42

54 in.

Reﬂ ection—Black Porcelain H8425 RFK-BLP-RAP54

Designer—Black Porcelain ** H8427 DFK-BLP-RAP54

Designer—Black Satin ** H8426 DFK-BLS-RAP54

Table 2 - Required Floor Kits

** Designer ﬂ oor kits require one media kit.

Media Kits

WARNING

DO NOT use Media with Reﬂ ection ﬂ oor. Improper operation

may occur.

• (1) Media, 5 lb bag

NOTE: See media kit instructions (P/N 900077-07).

Description Cat. No. Model No.

Reﬂ ective Black H8412 CRSHGL-RBLK

Reﬂ ective Blue H8424 CRSHGL-RBLU

Platinum H8413 CRSHGL-P

Goldﬁ nger H8538 CRSHGL-GF

Copper H8539 CRSHGL-C

Table 3 - Required Media Kits

OPTIONAL ACCESSORIES

Firebox Panel Backlight Kits

• (1) Left Lamp Bracket

• (2) Right Lamp Brackets

• (3) Lamps

• (1) Multi-Wire Harness

• (1) Proﬂ ame I Power Harness

• (1) SimFlame™ I Assembly

• (1) Reﬂ ector Panel

• (1) ProFlame™ II Light Wire Harness

Description Cat. No. Model No.

42 in. Illusion Firebox Panel Backlight Kit *** H8866 IPBLK-RAP42

54 in. Illusion Firebox Panel Backlight Kit *** H8429 IPBLK-RAP54

Table 4 - Optional Firebox Backlight Kits

*** "Cityscape" and "Illusion" ﬁ rebox backlight kit is designed for use with Citystape

and Illusion style Firebox Panel Kits.

Surround Kits

• (9) #10-16 x 3/8 Hex-head Sheet Metal Screws

NOTE: Surround and bezel should be installed together.

Description Cat. No. Model No.

42 in. Black Satin F2259 CS-BLS-RAP42

54 in. Black Satin F2256 CS-BLS-RAP54

Table 5 - Optional Surround Kits

Bezel Kits

• (1) Bezel Assembly

NOTE: Surround and bezel should be installed together.

Description Cat. No. Model No.

42 in.

Black Satin F2269 BZL-BLS-RAP42

Black Nickel F2267 BZL-BLNI-RAP42

Brushed Nickel F2268 BZL-BRNI-RAP42

54 in.

Black Satin F2266 BZL-BLS-RAP54

Black Nickel F2264 BZL-BLNI-RAP54

Brushed Nickel F2265 BZL-BRNI-RAP54

Table 6 - Optional Bezel Kits

Other Optional Accessories

Description Cat. No. Model No.

Power Vent Kit (manual P/N 506022-01) H7387 LPVK-110****

Adaptor Kit RAP54 (manual P/N 900077-04) H8574 PVK-RAP54 ****

Gas Conversion Kit, NG to LP (manual P/N 506019-90) H8540 GCK-RAPNP

Table 7 - Other Optional Accessories

**** For use with 42 in. and 54 in. models.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

To remove optional Bezel:

Grasp lower portion of bezel frame and pull forward to release

from bottom of door.

Swing bezel out slightly and lift up to clear top bracket from

door frame.

If Bezel is installed, barrier frame shown in Figure 2 will not be

present.

Remove glass door assembly

1. Remove the three (3) screws securing the lower edge of the

glass door assembly to the ﬁ replace (Figure 3).

2. Grasp the glass door assembly by the sides, swing the lower

edge out, and then lift up to unhook it from the ﬁ replace.

NOTE: Take care not to damage the glass.

3. Set aside the screws and glass door assembly in a secure

location for later reinstallation.

Glass Door Assembly

[CROSS-SECTION]

Barrier

Flanges

Door Trim

Barrier

Figure 2 - Removing the bezel

INSTALLATION INSTRUCTIONS

Complete all steps in the order shown, including the installation

of optional accessories (if applicable).

Remove barrier assembly

1. Remove the barrier assembly by lifting it up to disengage its

notches from tabs and pull directly away from the ﬁ replace.

2. To replace the barrier if damaged, remove the three (3)

screws from the top and bottom and one (1) screw from

each side. Reverse these instructions to install the new

manufacturer's barrier (Figure 2).

Figure 3 - Removing the glass door assembly

Remove bafﬂ e from ﬁ replace ﬂ oor, if installed

1. If unpacking the ﬁ replace for the ﬁ rst time, remove the

bafﬂ e from ﬁ replace ﬂ oor, where it is packed for shipping

(Figure 4).

2. Set aside the bafﬂ e in a secure location for later installation.

Bafﬂ e (as shipped)

Figure 4 - Removing the bafﬂ e

Access the control compartment

1. Remove the two (2) screws securing the burner assembly

to the burner brackets. Carefully slide the burner to the left,

to clear the venturi from the oriﬁ ce. Rotate the burner to

release the air shutter adjustment rod from the air shutter

lever (Figure 5). Lift and remove the burner assembly,

and set aside the screws and burner assembly in a secure

location for later reinstallation.

Air Shutter Rod

Figure 5 - Releasing the air shutter adjustment rod

Figure 6 - Accessing the control compartment

2. Remove the control compartment access door and gasket by

removing the twelve (12) screws securing it. Set aside the

screws, door, and gasket for later reinstallation (Figure 6).

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

4*For PF2 System, see Page 5 and Figure 12.

Control Compartment

Access Panel and

Gasket

Right Burner Bracket

Oriﬁ ce

Slot

Figure 7 - Accessing the control compartment

3. Loosen the front left screw of the right burner bracket. Remove

the other three screws, and rotate the bracket clockwise to

uncover the slot in the ﬁ rebox ﬂ oor (Figure 7).

Connect wiring harnesses for blower and optional

ﬁ rebox panel backlight kit - PF1 System*

NOTE: Use only original, factory-supplied wiring inside ﬁ replace.

1. In the control compartment, use a screwdriver or other

blunt object to carefully break the sealant around the wires.

NOTE: Be careful not to damage the wires.

2. Plug the multiwire harness (provided with the ﬁ rebox panel

backlight kit) into the SimFlame™ (ﬂ icker) module port with

the red wires (Figure 8).

NOTE: If not installing the SimFlame module, plug the

multiwire harness directly into the power harness (omit the

components outlined in Figure 8) and skip step 3.

Multiwire Harness from

Panel Backlighting Kit

SimFlame

Module (Plug into

AUX OUT

on Control

Module)

Power

Harness

If not using SimFlame

(flicker) module, omit

outlined components.

Figure 8 - Connecting multiwire harness and ﬂ icker module

3. Plug the power harness (provided with the ﬁ rebox panel

backlight kit) into the SimFlame Module port with the black

and white wires (Figure 9).

FAN AUX

OUT

SimFlame

Slot

SimFlame

Module

Fan Control

Module

Plug blower

into FAN port Plug lights into

AUX OUT port

Figure 9 - Connecting the lights and blower

4. Route the lighting wiring up through the access opening, and

slide it into the slot (Figure 9).

5. Plug the power plug end of the power harness into the AUX

OUT port on the ﬁ replace fan control module (Figure 9).

Install reﬂ ector (from optional ﬁ rebox panel backlight kit)

1. Insert the bottom edge of the reﬂ ector (provided with the

ﬁ rebox backlight kit) into the ﬁ replace ﬁ rst. Then, push the

top edge into rear of ﬁ replace (Figure 10).

NOTE: Lift the reﬂ ector over the tabs on the rear ledge of the

ﬁ replace

2. Align the large hole in the lower face of the reﬂ ector over the

screw in the ﬁ rebox rear wall.

3. Align the screw holes in the top and bottom edges of reﬂ ector

with the rear most holes in the ﬁ replace ceiling and rear ledge.

Secure the reﬂ ector using six (6) #10-16 x 3/8 hex-head sheet

metal screws provided with the ﬁ rebox panel backlight kit.

Reﬂ ector

Fireplace

Front

Tab

Rear Ledge

Figure 10 - Installing the reﬂ ector

Install side panels (from required ﬁ rebox panel kit)

1. Align the screw hole in the top ﬂ ange of the side panel with

the upper hole in the inside wall of the ﬁ replace (Figure 11).

2. Align the screw holes in the bottom ﬂ anges of the side

panel with the holes in the front and rear ledges.

3. Secure each panel with three (3) #10-16 x 3/8 hex-head

sheet metal screws provided with the ﬁ rebox panel kit.

Left Side

Panel

Right

Side

Panel

Left Side

Panel

Front

Ledge

Rear

Ledge

Figure 11 - Installing the side panels

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

CONNECTION AND ROUTE WIRING FOR OPTIONAL PANEL

BACKLIGHT KIT - SIT PROFLAME II SYSTEM

1. After accessing the control compartment (see Page 3, Figure

6), use a screwdriver or similar object to carefully break the

sealant around the wires, taking care not to nick the wires.

2. Plug in the Multi-wire Harness (provided with the Panel

Backlight Kit) into the SimFlame module port with the red

wires (Figures 8 and 12) and the light wire harness into the

light module harness.

3. Plug in the light wire harness (provided with the Panel

Backlight Kit) into the SimFlame Module port with the black

and white wires.

NOTE: If NOT installing the SimFlame (ﬂ icker) Module,

plug the Multi-Wire Harness directly into the light wire

harness (omitting the components outlined in Figure 8)

4. Route the wiring up through the access opening and slide it

into the slot (Figure 14).

5. Attach the wiring to each lamp assembly as described

below and shown in Figure 17:

a. Route one set of three leads (white/green/black)

through the hole in the front of the bracket.

b. Connect the green wire as shown in Figure 17.

c. Insert the lamp (with green wire attached) into the

bracket until the spring clip is engaged.

d. Attach the white (neutral) and black (hot) wires as

shown in Figure 17.

6. Carefully lay the Panel Backlight lamp assemblies and

wiring on the ﬁ replace ﬂ oor. The lamp assemblies will not

be installed until the back panel is installed (In Step 9,

Figure 18 on Page 6).

Figure 12 - Connecting the SIT PF II Module

Light Wire Harness

Light Module Harness

PF2 Module

SimFlame Module

Multi-Wire Harness

Red Wires

Install back panel

1. Insert the bottom edge of the back panel into the ﬁ replace

ﬁ rst, then position it in front of the previously installed

reﬂ ector (Figure 13).

NOTE: Lift the back panel over the tabs on the rear ledge of

the ﬁ replace.

2. Align the screw holes in the top and bottom edges of the

back panel with the holes in the ﬁ replace ceiling and rear

ledge. Secure using seven (7) #10-16 x 3/8 hex-head sheet

metal screws provided with the ﬁ rebox panel kit.

Fireplace

Front

Left Side

Panel

Back Panel

Reﬂ ector

Tab

Rear Ledge

Figure 13 - Installing the back panel

Route wiring for optional blower kit

NOTE: Use only original, factory-supplied wiring inside the

ﬁ replace. See the wiring diagrams on Page 11.

1. Route the wiring per the instructions (P/N 750028M).

Route wiring for optional power vent kit

NOTE: Use only original, factory-supplied wiring inside the

ﬁ replace. See the wiring diagrams on Page 11.

1. Route the wiring per instructions (P/N 506022-01).

Determine optional ﬁ rebox panel backlight kit wire

routing method

There are two approved methods for routing the wiring for the

optional ﬁ rebox panel backlight kit.

The preferred method is outlined in the following sections. The

alternate method is included for installations where the ﬁ rebox

rear ledge does not have backlight wire routing holes, and is

described in the Appendix section Route and connect optional

ﬁ rebox panel backlight kit wiring and install lamp assemblies

as shown on Page 6.

1. Determine whether the ﬁ rebox rear ledge has backlight wire

routing holes (Figure 14).

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

Backlight Wire

Routing Holes

Figure 14 - Routing wiring

2. If the ﬁ rebox rear ledge has backlight wire routing

holes, proceed with the instructions in Route and

connect optional ﬁ rebox panel backlight kit wiring

and install lamp assemblies below.

If the rear ledge does not have backlight wire

mounting holes, follow the instructions detailed in

Route and connect optional ﬁ rebox panel backlight

kit wiring and install lamp assemblies as shown on

this page.

Route and connect optional ﬁ rebox panel backlight kit

wiring and install lamp assemblies

1. Remove the three (3) cover plates in the lower front face

of the back panel. Discard the cover plates, but retain the

screws.

Figure 15 - Removing the cover plates, and routing the wiring

2. Route one set of three leads (white/green/black) through each

backlight wire routing hole in the rear ledge (Figure 14).

3. Route one set of three leads (white/green/black) through each

hole in the lower front face of the back panel (Figure 15).

4. With one set of three leads, connect the green wire to a

lamp (Figure 16).

5. Insert the lamp (with green wire attached) into a bracket

until the spring clip is engaged (Figure 16).

6. Connect the white (neutral) wire and black (hot) wire

(Figure 17).

Figure 16 - Attaching green wire to ﬁ rebox panel backlight

kit lamp, and inserting lamp into bracket

Figure 17 - Attaching black and white wires to ﬁ rebox

panel backlight kit lamp

7. Repeat the process in step 4 through step 6 for the

two remaining lamp assemblies.

8. Insert the three (3) lamp assemblies in the exact

orientation shown (Figure 18).

Figure 18 - Installing the lamp assemblies

9. Secure the lamp assemblies using the six (6) previously

removed screws from the cover plates (Figure 18).

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

Door gasket instructions

1. Reinstall the door. If the door does not fully close easily,

the door gasket will need to be dressed. See Figure 21 and

Warning below.

Correctly dressed Gasket.

Screwdriver works well

to dress gasket.

WARNING

The door should easily close without needing to

be pressed down. If it has to be pressed down to

close, the gasket in the top of the door should be

dressed so it lays on the glass.

Correctly Dressed Gasket Improperly Dressed Gasket

Improperly dressed gasket.

No gap between gasket

door channel.

Clean porcelain panels (if applicable)

1. If applicable, use non-ammoniated glass cleaner and a soft

rag to remove ﬁ ngerprints and smudges from porcelain

panels and ﬂ oors.

Install glass door assembly

1. Hold the glass door assembly by the sides, and hook the

top edge to the ﬁ replace. Then swing the bottom edge in

toward the ﬁ replace (Figure 20).

NOTE: Be careful not to damage the glass.

2. Align the screw holes below the door assembly with the

holes in the ﬁ replace, and secure using the (3) provided

screws.

Install bafﬂ e (provided with ﬁ replace)

1. With the bafﬂ e oriented as shown (Figure 19), slide the rear

tabs into the slots in the back panel.

2. While sliding the tabs into the slots, engage the front lip of

the bafﬂ e under the spring clips in the ﬁ rebox ceiling.

Bafﬂ e

Slots in

Back Panel

Spring Clip Firebox Ceiling

Tabs

Figure 19 - Installing the bafﬂ e

Figure 20 - Installing the glass door assembly

Figure 21 - Door gasket

Rating plate and lighting instructions

are attached to door bracket.

Glass Door Assembly

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

Gather and reseal all wiring

1. Gather all wiring and pilot connections together at the end

of the slot, and reseal with high-temperature sealant, such

as Mill-Pac® (not provided) (Figure 7).

2. Reposition the right burner bracket and secure with the

three (3) previously removed screws; tighten the fourth

screw (Figure 7).

3. Replace the control compartment access door and gasket,

and secure with the twelve (12) previously removed screws

(Figure 7).

4. Carefully slide the burner assembly venturi onto the oriﬁ ce.

While placing the burner assembly onto the brackets,

reinstall the air shutter adjustment lever (Figure 5). Secure

the burner assembly with the two (2) previously removed

screws.

Install rear ﬂ oor section (from required ﬂ oor kit)

1. Place lower back edge of rear ﬂ oor section on rear ledge of

ﬁ replace, behind the tabs (Figure 22).

2. Align outermost front hole on either side of rear ﬂ oor

section with hole in center lower tab in each side panel. Pull

rear ﬂ oor section forward until it butts against the burner,

and secure using ﬁ ve (5) #10-16 x 3/8 hex-head sheet

metal screws provided with the ﬂ oor kit.

Rear

Floor

Section

Rear

Ledge

Tab

Side Panel

(Center Lower Tab)

Figure 22 - Installing the rear ﬂ oor section

Install front ﬂ oor section (from required ﬂ oor kit)

1. Engage the lower front lip of the front ﬂ oor section under

the locking clips attached to the ﬁ replace front ledge, and

then slide it back (Figure 23).

2. Align the notches in the back edge of the front ﬂ oor section over

the holes in the rear ﬂ oor section. Push the front ﬂ oor section

backward until it butts against the burner, and screw the front

ﬂ oor section as shown in Figure 23.

Locking Clip

Front

Ledge

Notch

Rear

Floor

Section

Front

Floor

Section

Lip

Figure 23 - Installing the front ﬂ oor section

Install media (from optional media kit)

WARNING

• Handle media only when cool. Turn OFF all electricity

to the appliance before installing media. Media gets

very HOT during ﬁ replace use and will remain hot up

to ONE HOUR after the gas supply is turned off.

• Any attempt to use media not speciﬁ ed for your ﬁ replace

conﬁ guration will result in incomplete combustion,

sooting, and poor ﬂ ame quality, and will void the

warranty.

• Do NOT mound up media, especially on the burner.

• If using multiple colors of media, NEVER use more

than ﬁ ve (5) pounds total (approximately) at one time.

• Do NOT allow media to get into the pilot hole.

1. If installing a ﬂ oor kit that requires media, place an even

layer of media in the recessed area around the burner (see

bold outlined area in Figure 24; also refer to Figure 1).

Figure 24 - Placement of media

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

Install optional surround

1. Remove clean face trim and install brackets - Remove

the clean face frame shown in Figure 27. Attach surround

mounting brackets to unit (10 screws). See Figure 25.

Surround will be mounted to these brackets (see Figure 26).

2. Attach the surround and secure it using the nine (9) screws

provided with the surround kit (Figure 26).

Finishing with optional Surround and Bezel

1. With unit in framing, secure nailing ﬂ anges to the wall framing.

2. Retrieve and secure heat shield to top front of unit with two

screws.

3. Remove the clean face frame (see Figure 27).

4. Place insulation ﬂ at across the top of the ﬁ replace lengthwise

behind heat shield.

5. Install top, bottom and two (2) side surround support pieces

with screws from step 1 (see Figure 27).

6. Cut top noncombustible ﬁ reboard to size and install ﬂ ush with

top frame pieces (side noncombustible boards not used).

7. Install glass media.

8. Remove top, bottom and two side trim pieces of barrier as-

sembly. Insert remaining barrier assembly into bezel assem-

bly and attach with screws.

9. Reinstall the door.

10. Attach surround to surround support with six (6) screws.

11. Hang barrier assembly on door and snap underneath door.

Surround mounting

brackets (provided

with surround kit)

Clean

Face Frame

(removed first)

Bezel and Barrier

(added after Surround

- not shown)

One (1) Top non

-combustible

board

Clean

Face Frame

(removed first)

Figure 25 - Surround Mounting Brackets

Figure 26 - Installing optional surround

Figure 27 - Remove clean face trim and install brackets

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

6 Secure Barrier screen to Bezel assembly with screws

removed in step 2.

7 Install barrier/bezel assembly onto glass door.

4. Hook the bezel upper ﬂ ange to the top edge of the glass

door assembly, and then swing the lower edge of the bezel

toward the door (Figure 29).

5. Gently push the lower edge of the bezel to attach the bezel

lower ﬂ ange to the lower edge of the glass door frame.

[CROSS-SECTION]

Barrier

Flanges

Door Trim

Barrier

Figure 28 - Place barrier screen on Bezel assembly

Figure 29 - Barrier assembly

Figure 30 - Secure Barrier screen to Bezel assembly

Installing Barrier into Bezel

NOTE: See Barrier Removal Instructions on Page 3, if

applicable.

1. Remove barrier assembly that is shipped with unit.

2 Remove barrier screen from assembly by removing 3

screws top and bottom and one on each side.

3 Place barrier screen on Bezel assembly. See Figure 28.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

CAUTION

Ground supply lead must be connected to the wire attached to the green ground screw located on the outlet box. Failure to

do so will result in a potential safety hazard. The appliance must be electrically grounded in accordance with local codes, or

in the absence of local codes, the National Electrical Code, ANSI/NFPA 70, latest edition (in Canada, the current CSA C22.1

Canadian Electrical Code).

Red

Green

Ground

Screw

Black

Hot Side of

Receptacle

Tab Cut

Tab Intact

Green White

Neutral Side of

Receptacle

120 VAC—Black

Neutral—White

Ground—Green

J-BOX / RECEPTACLE

WIRING

120V, 60HZ, 1PH

Junction Box

Field Wired

Factory Wired

(Power Supply

Unswitched)

Figure 31 - Junction Box Wiring

Pilot Tube

COLOR CODE:

B = BLACK

BB = BROWN W/BLACK STRIPE

BG = BROWN W/GREEN STRIPE

BL = BLUE

BR = BROWN

G = GREEN

GY = GRAY

O = ORANGE

R = RED

W = WHITE

Y = YELLOW

Spark Electrode

Flame Sensor

IPI Pilot

885 Valve Optional

Split Flow

Battery Holder w/Switch

ON/ Remote

/OFF

Battery Holder

Wire Harness

Reset Switch

“see instructions”

Optional Variable Light

Power Vent Blower

Power Vent

Models Only

Optional Circulation

Blower

Air Pressure Switch

Power Vent Only

Models w/o pressure switch have

these connectors plugged together

Main Wire

Harness

Main Power Cord

Control Module

Fuse

ELECTRONIC WIRING DIAGRAM

Ground Y

Schematic Representation Only

Battery Holder w/Switch

ON/Remote/Off

Figure 32 - Gas Valve Electronic Wiring Diagram - SIT ProFlame II

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

P/N 900077-05 Rev. A 09/2016 1508 Elm Hill Pike, Suite 108, Nashville, TN 37210

IHP reserves the right to make changes at any time, without notice, in design, materials,

speciﬁ cations, prices and also to discontinue colors, styles, and products. Consult your local

distributor for ﬁ replace code information.

APPENDIX: ALTERNATE INSTALLATION INSTRUCTIONS

Route and connect optional ﬁ rebox panel backlight kit

wiring and install lamp assemblies

NOTE: These instructions should be used in place of Route and

connect optional ﬁ rebox panel backlight kit wiring and install

lamp assemblies on Page 6, for ﬁ replaces without backlight

wiring kit routing holes as shown in Figure 14 on Page 6.

1. Route one set of three leads (white/green/black) through

the hole in the front of the bracket (Figure 33).

Front of Mounting Bracket

Figure 33 - Routing wires through lamp bracket

2. Connect the green wire to the lamp (Figure 34).

3. Insert the lamp (with green wire attached) into bracket until

the spring clip is engaged (Figure 34).

4. Connect the white (neutral) wire, and black (hot) wire

(Figure 35).

Figure 34 - Attaching green wire to ﬁ rebox panel backlight

kit lamp, and inserting lamp into lamp bracket

Figure 35 - Attaching black and white wires to ﬁ rebox

panel backlight kit lamp

5. Repeat the process in step 1 through step 4 for the two

remaining lamp assemblies.

6. Carefully lay the ﬁ rebox backlight lamp assemblies and

wiring on the ﬁ replace ﬂ oor. The lamp assemblies will not

be installed until the back panel is installed (in a later step).

7. Remove the three (3) cover plates in the lower front face

of the back panel. Discard the cover plates, but retain the

screws.

8. Insert the three (3) previously assembled lamp assemblies

in the orientation shown (Figure 36).

NOTE: The wires will be routed under the rear ﬂ oor section

in the next step.

9. Secure the lamp assemblies using the six (6) previously

removed screws from the cover plates.

Cover Plate

Note orientation of each

lamp assembly.

Figure 36 - Installing the lamp assemblies

NOTE: When installing the rear ﬂ oor, route the ﬁ rebox

backlight wiring through the notches under the rear ﬂ oor

section. Be careful not to pinch or damage the wires.

Astria Fireplaces Rhapsody Instruction Sheet

Brand: Astria Fireplaces

Model: Rhapsody

Category: Fireplaces

Type: Instruction Sheet

Download PDF

report

Astria Fireplaces Rhapsody Instruction Sheet

Astria Fireplaces Rhapsody Instruction Sheet

Related papers

Other documents