Rugged Ridge 11540.48 Installation guide

Brand
Rugged Ridge
Model
11540.48
Type
Installation guide

Rugged Ridge 11540.48 is a modular HD front bumper RRC Hoop designed to provide additional protection and functionality to your Jeep. It can be used for vehicle recovery, mounting aftermarket lights, and adding a winch or bumper ends. The RRC Hoop is made of high-quality materials and is easy to install. It comes with all the necessary hardware and instructions. Whether you're an experienced off-roader or just starting out, the Rugged Ridge 11540.48 is a great addition to your Jeep.

Rugged Ridge 11540.48 is a modular HD front bumper RRC Hoop designed to provide additional protection and functionality to your Jeep. It can be used for vehicle recovery, mounting aftermarket lights, and adding a winch or bumper ends. The RRC Hoop is made of high-quality materials and is easy to install. It comes with all the necessary hardware and instructions. Whether you're an experienced off-roader or just starting out, the Rugged Ridge 11540.48 is a great addition to your Jeep.

11540.48
Jeep® CJ, YJ, TJ Modular HD Front Bumper RRC Hoop
Contents:
1. RRC Hoop (1)
1. If installing as part of a new installation, place center section of bumper onto frame rails, but do not
yet attach. If RRC Hoop is being added to an existing installation, remove existing Hoop and D-Rings
from Center Section. Center Section should be sitting on the frame rails, but not attached (Figure 1a).
Place RRC Hoop over Center Section (Figure 1b) and align 8 holes on top and 8 holes on front (Figure 1c).
Figure 1a Figure 1b Figure 1c
2. Install 8 top bolts ( provided with the Center Section) through the RRC Hoop and into the Center
Section (Figure 2a). Do not tighten bolts yet. Install 8 front bolts (provided with Center Section)
through the RRC Hoop and into the Center Section (Figure 2b).
Page 1 of 2
1
Figure 2a Figure 2b
3. Once all 16 bolts have been started, tighten the front 8 bolts, followed by the 8 top bolts.
Installation is now complete! Note: When used for vehicle recovery, only the D-Ring mounts at the
base of the RRC Hoop are to be used. RRC Hoop is not to be used for towing or vehicle recovery.
NOTE: If aftermarket lights are to be mounted to supplied tabs DO NOT block the function of factory
turn signals or headlights. Lights can be mounted under bars if desired. Spacers will be needed.
Page 2 of 2
Congratulations on the purchase and installation of a quality Rugged Ridge product! Ask your retailer
about the following additional accessories to the JK Modular HD Bumper:
11540.40 - Winch Center Section 11540.42 - Optional Bumper Ends
11540.14 - Optional Hoop - Black
11540.16 - Optional Hoop - Stainless
11540.17 - Optional Stainless D-Rings
11540.13 - Optional Stinger
Please find warranty card supplied with product for more information. Warranty card should be filled out and returned to address listed below.
LIMITED WARRANTY
Applies to Rugged Ridge Products by Omix-Ada Inc.
Omix-Ada Inc.
460 Horizon Dr. Suite 400
Suwanee, Georgia 30024
  • Page 1 1
  • Page 2 2

Rugged Ridge 11540.48 Installation guide

Brand
Rugged Ridge
Model
11540.48
Type
Installation guide

Rugged Ridge 11540.48 is a modular HD front bumper RRC Hoop designed to provide additional protection and functionality to your Jeep. It can be used for vehicle recovery, mounting aftermarket lights, and adding a winch or bumper ends. The RRC Hoop is made of high-quality materials and is easy to install. It comes with all the necessary hardware and instructions. Whether you're an experienced off-roader or just starting out, the Rugged Ridge 11540.48 is a great addition to your Jeep.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents