Atdec VF-M Installation guide

VF-M
Atdec
Brand
Atdec
Model
VF-M
Category
Flat panel desk mounts
Type
Installation guide

This manual is also suitable for

Atdec VF-M is a versatile and user-friendly single or multi-user monitor arm that provides a wide range of motion and adjustability. With its sturdy construction and durable materials, it ensures stability and longevity. The VF-M is designed to enhance your productivity and comfort by allowing you to position your monitor(s) at optimal viewing angles and heights. It features a flexible arm that enables smooth and effortless movement, making it easy to find the perfect position for your screen.

Atdec VF-M is a versatile and user-friendly single or multi-user monitor arm that provides a wide range of motion and adjustability. With its sturdy construction and durable materials, it ensures stability and longevity. The VF-M is designed to enhance your productivity and comfort by allowing you to position your monitor(s) at optimal viewing angles and heights. It features a flexible arm that enables smooth and effortless movement, making it easy to find the perfect position for your screen.

A Component Checklist - Check you have received all parts against the component checklist prior to installing
Installation Instructions
Pole Assembly
5mm Allen
Key
User
Operating
Card
(See note at top
of page)
IMPORTANT:
The “User Operating
Card” must be left
with Visidec Focus
Micro once installed
Bottom
Top
Bits Box
Bolt Through
Base
Steel Washer
M8x30mm
Screw
Cable Clip
2mm Allen
Key
Display Mounting
Screws
M4x16mm
(x4)
M4x12mm
(x4)
M4x10mm
(x4)
Desk Clamp Box
5mm Allen
Key
Desk Clamp Bracket
Pressure Plate
M8 Desk
Clamp Screw
Bolt Through
Steel Washer
Bolt Through Base
M8 Desk Clamp Screw
(found in the Desk
Clamp Box)
5mm Allen Key
9mm (³/
8
”) Hole
Drill a 9mm (³/
8
”) hole in the work
surface at the desired position and
assemble as shown below.
Work Surface
Pole
Assembly
Step 3: Adjust the height of the Pressure Plate to suit the
work surface and tighten firmly in the desired location.
5mm Allen Key
Tighten Firmly
Desk Clamp
Pole Assembly
OR
B1
B2
Step 1: Attach the Desk Clamp Bracket
to the bottom of the Pole Assembly using
the M8x30mm Screw. Tighten firmly
using the 5mm Allen Key. Ensure the
Visidec logo is facing the front as shown.
M8x30mm
Screw
Bottom
Bottom
Step 2: Install the M8 Desk Clamp
Screw and Pressure Plate as shown.
Desk
Clamp
Bracket
5mm
Allen Key
Bolt Thru
Base
Pole
Assembly
Pressure
Plate
M8 Desk
Clamp Screw
5mm
Allen Key
NOTE: It is recommended that the Pole
Assembly be clamped to the rear or side
edge of the work surface
Suits 12mm (½”)
to 38mm
(1½”)
thick work
surfaces
ADJUSTMENT RANGE
Cable Balls
(x2)
Slot
NOTE:
Ensure the slot in the Pole Assembly faces away from
the user.
It is recommended that the Pole Assembly be mounted
towards the rear edge of the work surface
Tighten
Firmly
D Mount the Display
As LCD Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the mounting hole pattern does not comply with the international VESA
standards. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 21.12.06 ©
For Displays with 75mm x 75mm
(3” x 3”) mounting hole patterns
M4 Display Mounting Screws
Step 1:
Connect
cables
NOTE: Leave enough slack in the
cables to allow for movement
E Cable Management
NOTE: If Focus Micro
is to be used in a multi-
user environment, use
the supplied Cable Clip
to secure the display’s
cables to the pole.
C Unlock/Lock Arm Rotation (Note: Focus Micro comes assembled in the “Locked” position.)
If you wish your Focus Micro Arm to have 360° rotation
about the Pole you will need to un-lock the arm’s rotation.
2mm
Allen Key
For Displays with 100mm x 100mm
(4” x 4”) mounting hole patterns
M4 Display Mounting Screws
F Leave the “User Operating Card” with Visidec Focus Micro
Leave the “User Operating Card” secured to the Visidec Focus Micro for the user’s reference.
Step 2: Insert cables into slot, using cable
balls to hold them in place
(single user only)
Cable
Balls (x2)
Step 1:
Ensure the hole for the
Grub Screw in the Micro
Arm is lined up with
the centre of the Slot
in the pole.
Step 2:
Re-insert the Grub
Screw previously
removed. Turn the
Grub Screw clockwise
until it is tight. Do
not over-tighten
UN-LOCK: LOCK:
2mm Allen Key
Slot In Pole
Pole
Micro Arm
Cable
Clip
Grub Screw
OR
Step 1:
Unlock the arm by turning
the Grub Screw anti-
clockwise removing the grub
screw completely.
(
NOTE:
Store the Grub
Screw in a safe place if you
are to return the arm to the
Locked position.)
If you have un-locked the Focus Micro Arm, but wish to fix
rotation around the pole, you will need to lock the arm.
Grub Screw
Hole
Grub Screw
  • Page 1 1
  • Page 2 2

Atdec VF-M Installation guide

VF-M
Atdec
Brand
Atdec
Model
VF-M
Category
Flat panel desk mounts
Type
Installation guide
This manual is also suitable for

Atdec VF-M is a versatile and user-friendly single or multi-user monitor arm that provides a wide range of motion and adjustability. With its sturdy construction and durable materials, it ensures stability and longevity. The VF-M is designed to enhance your productivity and comfort by allowing you to position your monitor(s) at optimal viewing angles and heights. It features a flexible arm that enables smooth and effortless movement, making it easy to find the perfect position for your screen.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents