Visidec VF-AT-NK Installation guide

Category
Notebook arms & stands
Type
Installation guide
visidec
visidec
Focus Notebook Mount Accessory
Installation Instructions
Component Checklist
IMPORTANT INFORMATION
! IMPORTANT - Install Visidec Focus Notebook Mount as per Installation Instructions.
! This product is deisgned to be used in conjuction with an external keyboard and mouse.
! To be used with existing Visidec Focus Mount.
! Visidec Focus Notebook Mount supports Notebooks up to 18”, weighing up to 8kg (17 1/2lbs).
! The Manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
VF-AT-NK
Step 2. Remove existing Arm and Monitor from Visidec Pole (ensure monitor cables are unplugged)
Notebook Tray and
Arm Assembly
Step 7. Cable Management - Ensure Arm is fully extended.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 22.04.09 ©
Installation Complete
Your Visidec Focus Notebook Mount installation is complete and ready for use.
IMPORTANT:
The “User Operating
Card” must be left with
Visidec Focus Articulated
Arm once installed.
Hardware
Primary Arm
Cable Cover
Secondary Arm
Cable Cover
Self Adhesive
Hook-and-Loop
Fasteners (x4 sets)
A. Insert tabs...
B. Push in...
C. Then push up
Insert Secondary
Arm Cable Cover*
Insert Primary
Arm Cable Cover*
*To insert Cable Covers:
TIP: Leave enough slack in the cables
at the joints to allow full movement.
Route the Cables underneath the Arms,
inserting the Primary and Secondary
Arm Cable Covers to hold the Cables in place.
Hand Grip
Whilst supporting the weight of the
Monitor, unlock the Hand Grip.
Lift the Monitor and Focus Arm,
removing them both from the
Visidec Pole.
Hand
Grip
Monitor
Visidec Pole
Remove the Pole Top Cap and
5mm Allen Key from the Visidec
Pole.
Visidec
Pole
Pole Top
Cap
5mm Allen
Key
Step 8. Display Alignment
Set the height and position of the Notebook Tray and Monitor as desired.
The height can be adjusted by unlocking the Handgrips (see Steps 3, D and E).
For the optimal position of your display, refer to the Ergonomic Guidelines in your ‘User Operating Card’.
FRONT:
BACK:
Handgrips
UNLOCK
UP
UP
Step 3. Attach the new Arm Assembly onto the Visidec Pole
Step 4. Re-install the existing Arm and Monitor
A. Slide the Handgrip onto the
top of the Visidec Pole so the
Handgrip Tab protrudes.
B. Slip the Arm Assembly over
the Handgrip Tab and then
onto the Visidec Pole.
Arm Assembly
C. Slide the Arm Assembly
towards the base of the Visidec
Pole.
D. Lock the
Handgrip
Step 5. Install the Notebook Computer
A. Adjust the Support Tabs
to suit the width of your
Notebook Computer.
NOTE: Ensure that the
Support Tabs do not
obstruct any cable ports.
Notebook
Tray
Notebook
Computer
B. To increase stability, use the Self Adhesive
Hook-and-Loop Fasteners supplied:
UÊÊ*iiÊvvÊÌiÊL>V}Ê«>«iÀÊvÀÊÌiÊ>ÃÌiiÀð
UÊÊÌÌ>VÊ>ÃÌiiÀÃÊÌÊÞÕÀÊ ÌiLÊ
Computer and the Notebook Tray.
UÊÊÃÕÀiÊÌ>ÌÊi>VÊÃiÌÊvÊ>ÃÌiiÀÃÊ>Ài
correctly aligned, i.e. Hook to Loop.
Support
Tabs (x2)
Notebook
Tray
>ÃÌiiÀÃÊÊÝ{®
Handgrip
Tab
Handgrip
C. Position your Notebook Computer
onto the Notebook Tray.
>ÃÌiiÀÃÊ«ÊÝ{®
C. Replace the Pole Tap Cap and 5mm
Allen Key, inserting them into the top of
the Visidec Pole.
A. Slide the existing Arm and
Monitor onto the Visidec Pole.
B. Lock the Monitor Arm Handgrip.
Handgrip
Pole Top
Cap
5mm Allen
Key
Step 6. Connect Cables
Lift the Cable Management Clip on the back of the
Notebook Tray, and route the Cables underneath.
Release the Clip to hold the Cables in place.
Cable
Management Clip Cables
LIFT
Connect cables to your Notebook Computer.
Cables Notebook
Computer
LOCK
  • Page 1 1
  • Page 2 2

Visidec VF-AT-NK Installation guide

Category
Notebook arms & stands
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI